I have 03 F-250 with a 5.4 in it. Recently noticed the gas gauge is not moving much and seems like it will not go below half a tank. The gauge will go up however when i put gas in it. I just put techtron in it last night to see if this might work. Wasn't to sure if i did a battery reset on the truck if that may work as well.
View 2 RepliesI recently bought a 2005 Ford F250 Super Duty, diesel 6.0.
As I was driving to work this morning I noticed that the fuel gauge read almost full when it should have only had a half tank. A little while later I heard a beep and saw that the gauge was now on empty with a "Low Fuel" message displayed. Then I noticed the heater was suddenly blowing cold air.
I've only had the truck for a few weeks, but haven't had any other problems. I did replace the CD receiver and all of the instrument cluster lights a couple weeks ago, but everything seemed to be working fine after.
I have a 2003 F250, 4x4, 5.4L and today my fuel gauge stopped working. I don't know if it had anything to do with a stall, I was on an exit ramp and the truck cut off, I quickly restarted and no issues after that. Other than the fuel gauge not working at this point.
I looked at the fuse panel diagram and there is no fuse for just the fuel gauge. The only thing I see is #35, instrument cluster. The rest of my instruments are working, so what else would cause the fuel gauge to stop working? It had a little over a half of a tank before the stall, after the stall it went down to less than half. I filled up shortly later and it's just stuck at less than half.
As I was driving to work yesterday I noticed my fuel gauge going from half tank all the way to full going down the highway. I started looking at the rest and they seem to be in there normal spots. I looked up and watched the outside temp go from 40 degrees to 5. This morning the fuel gauge goes straight to full and the outside temp bounces between 2 degrees and 10. What may be going on to cause this?
The truck is a 2000 F350 crew cab with a 7.3 Power Stroke
I've got a 2003 F250, SD, 5.4L Triton that I've owned since new. It has 205,000 kms on it and has run flawlessly since owning it.
Yesterday I went to use the truck after it sitting for about 2 weeks, which isn't uncommon for this time of year as I'm in the landscaping business. It never sits long, though as I make a point of using all the trucks, periodically, just to "blow the stink off" as my Dad would say.
Anyway, when I fired it up the gauge was drop-dead below "E" so I go to fill it up and it takes in fuel and it won't take a drop more. I got under the truck and knocked on the tank in various spots and the tank seems almost plum full.
When I power the truck off and back on, all the gauges come to life and settle on their appropriate readings, except for the fuel gauge. It powers up to full and then drops to below "E" as though I had turned the truck off again.
My question is, am I reasonably safe to assume my sending unit has bitten the dust? I figured that since the gauge comes to life upon startup and then drops to "E" after the rest of the gauges initialize, the fuel gauge itself probably isn't the problem?
Is there a chance that as I drive it over the next few days, and the tank empties, maybe the "sloshing" of fuel might dislodge a stuck part?
1999 F250 V10 gas. I changed out the fuel pump, and now the gauge doesn't work. Checked all fuses - they're good. Is there any possibility that I could have accidentally pinned the float under the pickup sock, or got it hung somewhere? Is this a common occurrence? Don't really want to drop the tank again - but looks like I will have to in order to check/fix.....
View 3 RepliesRecently had extensive work done on my 2005 F250 PSD. 4 injectors replaced, fuel regulator, and STC fitting on HPOP.
Got the truck back, and the fuel gauge, and "distance to E" display are working intermittently.
When the truck went in for repair, it was about 1/8 tank. After repairs, shop put about 30 miles on the truck.
I picked it up, and the gauge read E, and display said 0 kms to E. I filled the truck up, and the gauge still read E, and said 0 kms to E.
I then drove for a while, then powered down, and back up again, and gauge read below E (like when truck not running), and display had 4 dashes...no numbers, for distance to E. I powered down, and then back up, then it read 696 kms to E, and gauge working normally.
This morning, on a cold start, the 4 dashes, and empty reading returned. I shut off truck, and restarted it, and it started working again.
Could the shop have damaged the sending unit, while driving 30 miles, with so little diesel in the tank?
My dads 05 f250 6.0 PSD. He says he'll take off in the morning and the fuel gauge will randomly drop to empty and trigger the low fuel light, but then also the Check Engine Light will come on. My brother did a code scan and no codes come up. Where we should be looking to remedy this one?
View 14 RepliesI just replaced my fuel pump to avoid another tow truck ride and now my fuel gauge is off. I filled up the truck today and the fuel gauge is only showing half a tank. I turned the truck on and off several times to try to reset it, but that didn't work.
Truck is a 2003 with the 5.4.
2003 F 350 gauge indicates water in fuel. Second hand truck, the hex socket in the plug has be rounded out. Removing plug
View 1 RepliesJust bought a watchdog monitor by Bullydog. What are the normal levels for Boost, MAF, Load for a SD Twin Turbo 6.0L?
View 7 Replies177,000 miles, fuel pump was replaced just before I purchased it a few weeks ago. Truck has been running like new until today when it started doing this completely out of the blue. If you watch the video, the sound is not off, the tach is moving independently of the sound of the actual revs. Occasionally when doing this, the fuel gauge drops to zero. Thinking this is an electrical issue somewhere.
YouTube.....
My '03 V10 F250 gas with 135k miles on it went from showing weird fuel levels last week, showing low when I just put $40 in it to now being absolutely below empty, pegged as far south as it can get. I have a CEL light on too but my OBD test shows, "N/A 01-01". So all I can think is that there may be an open/short circuit that the OBD cannot diag.
I replaced my fuel pump about 2 years ago with a replacement AutoZone unit and all had been fine since then. I just do not remember if the fuel level sensor was part of the pump itself or a separate item. If it's a integral part of the pump I should be able to go back to AutoZone and get a warranted replacement.
Is there anything I can test a forehand before either pulling the tank or doing a dump-truck again?
New to me 2003 F250 Super Cab 6.8 V10. Great condition inside and out. 68,000 miles. Began smelling fuel (gas) a few days after driving it 250 miles from purchase location. Traced leak down to the top of the gas tank. Staining was visible around the rear vent. Applied about 5 psi to the tank and sprayed soap around until I saw bubbles coming from a hairline crack at the rear vent connection. Its where the fitting for the hose comes out of the tank.
My first choice would be to hot weld the crack. I'm not very comfortable with the idea of a heat source near a gas tank. I'm not sure, but the heat from the plastic welder might be hot enough to ignite fumes? Second option is to try some industrial 2 part epoxy (PIG) and seal it with that. Is there pressure inside the tank, and if so how much? Can try this fix with epoxy or JB Weld?
This morning while driving cold a fuel leak started on my truck it's a very heavy leak wondering what are the most common leaks on an 2003 F250 6.0L are so I can start there.
View 3 RepliesI have a 2006 Ford F-250 5.4l the symptoms are when it's warm it has half power and it will stall at idle. What I have done with the truck is.
New cam phasers
new chain
new tensioners
new vct solenoids
new oil pump
new plugs
new ignition coils
new stock cam shafts
new rockers
new lash adjusters
new exhaust manifolds both sides
new muffler
oil change with the right oil
ran it with sea foam in the crankcase before oil change
new fuel pump module
new evap vent control
new abs speed sensor
I cleaned throttle body with brake cleaner ... Scanned it after a 15 min ride of having to use 2 feet to drive it. The engine codes that came up are p0022 iacv short to ground and p1000 readiness test not complete. I also got p1804 4 wheel drive high indicator circuit failure p1808 4 wheel drive low indicator circuit failure .... Not sure what else to try.
My 07 has developed a steering gear issue.....it suddenly developed about a quarter to a half turn of slop......mechanic checked the front end and found everything to be tight and right so......I ordered a Redhead rebuilt box and will replace it upon it's arrival. My question is How often do these boxes go bad and if and when they do is it at all safe to drive the vehicle with that much play? I have to drive it about 15 miles to get to my mechanic ( far too cold for me to do it at home) and I also plow a couple of yards commercially and will need to use it there in the event of a snow storm.
View 8 RepliesEverything was working fine, getting down to about 1/4 tank. I do the usual, fill up, startup, reset the trip, and look at my level and it hasn't changed, neither has the 'km until E'. What would cause this? Failed Sender? No check engine light (yet). I guess I'll be watching the trip meter for a while.
View 8 RepliesI was driving home the other day when all of a sudden all of my electronics in my truck turned off. Turned out when I got home my battery terminal was loose so it ended up shorting out. (fixed that) but when that happened my fuel was just under half way. The next day I filled up and was pulling a 3,000 pound trailer. My gas gauge didn't move at all, all weekend it was stuck at full until I actually went over a bump and it started moving down to a quarter. I knew here was no way I could go all weekend pulling a trailer and only lose a quarter of gas so I filled up again and was only be able to fill up 14 gallons.
View 4 Replies2000 v10 f350 single tank...fuel gauge is stuck on full. I'm on the road so I don't have my drawings so I tried some quick troubleshooting. If I remember right 160k or so is full and 20k ohms is empty...so I unplugged the sender from the harness which should be open and the gauge should read empty. With key on its reading full. I then followed the harness and unplugged it near the brake booster...key on it reads full. Just wanted to make sure I'm not doing anything wrong before I rip the dash apart.
View 6 RepliesI have a 2000 ford F 250 with V-10 engine with fuel gauge stuck. The problem started in the winter a couple years back on a cold night when I fueled the truck with it running. The fuel gauge never went down. I assume this would indicate a stuck float? I dropped the tank and noticed a loose yellow wire. I can't see that the wire was attached anywhere though? A V-10 is not the engine to be guessing with on fuel...
View 1 Replies