Ford Super Duty (1999-2016) :: 2003 F250 - Truck Pulls To Right When Driving And Pulls To Left On Braking
Apr 22, 2014
My 2003 F250 6.0 pulls to the right when driving at any speed. In order to keep it going straight the steering wheel must be slightly tilted to the left, not much but a little. When the brakes are applied hard it will go to the left slightly if you are not holding the wheel good. Neither of these are terrible, just a nuisance. I'm worried about uneven tire wear too. One front wheel bearing was replaced a few weeks ago. It had this problem before that and still does after. Does this sound like an alignment or maybe something more?
View 13 Replies
Advertisement
1999 F250 SD 4x4 7.3 PSD ... My truck has 198K miles on it. It pulls to the left as I drive it. So I took it to a shop to have the alignment checked. They told me that the front outer tie rod was bad and needed to be replaced. And of course they said they needed to put in a set of caster camber bushings to do the alignment. They quoted $400 to change the tie rod out. I said I would do that. They gave me the print out from the alignment but reading it the only thing that was out was the toe. Left tire was toe out and the right tire was toe in, which to me would cause it to pull to the left.
I got under the truck and the steering link, piece that goes from steering box to right side/tie rod, is not tight...I can move it up and down and it clunks when I roll it up. I have a clunking noise when I drive it and go over bumps also. Could this be the clunking noise? Also, if I replaced the ends of the steering link, that would tighten up but possibly push the steering back to the right some to straighten out the tires? I have read alot of threads talking about the clunking being tied to the sway bar bushings being bad but the clunking I get by rolling the steering link up and down sounds alot like the noise I am hearing.
Also, when looking at the axles where they go into the knuckle, there is a loose plastic ring on both sides. Is this part of the dust shield or an oil seal?
View 5 Replies
Well, I tried this Death Wobble Kit on my Ford F350 Super Duty from a company called WC Motorsports. Had it installed at a Ford Dealership. DO NOT BUY this kit. Missing parts right out of the box. Also makes a horrible clanking noise after install. Piece of junk. Possible fix to one problem only to have multiple other problems:
1. Clanking Noise
2. Truck pulls to the left
3. Have to cut the factory subframe. (Never a good idea)
4. Changes the degree (not recommended by Ford)
View 10 Replies
My 2012 f350 6 lift when I push the brakes it pulls to the left kinda bad and the steering wheel is off to the right..
View 4 Replies
Well just called it quits from working on the truck tonight. Had some issues with my brakes going to the floor and pulling to the right some, so I went to auto zone and bought all new pads. Didn't think it was time yet because I just replaced the rotors, pads, calipers, maybe 20,000 miles ago. When I got home and everything pulled apart I looked at the pads on the truck and they still had 60% life. I looked closely and noticed that the guider pins on the caliper bracket (front drivers side) were seized. I figured this is what was causing my truck to pull. Looked on the passenger side and it looked similar. Went back to auto zone and returned the pads and bought new brackets for both sides. I got the drivers side replaced and working and all seemed well. I got to the passenger and had a hell of a time getting the pistons on the caliper to compress so I could get it off. Once I finally got it, I noticed the pins on that side were not seized. I bought 2 sets of guider pins so I took the old ones out and greased up the new ones and installed them. Put everything back together and took the truck for a drive. Everything seemed normal at first, but once I got on the highway and hit the brakes, my truck pulled to the left. HARD.. Im assuming this is because of the pistons on the passenger side caliper I was having a problem with, not having the piston compress all the way causing my truck to pull. While I was looking at the caliper, I also noticed what '"looked" like a grease fitting, and also a bleeder valve a few inches away from it. Am I crazy, or is that fitting for bleeding the brake lines also...?
View 5 Replies
When you turn the headlight switch to the headlight on position, you can pull it out exhibiting a positive click as if it is an additional switch for maybe optional fog lights. If the headlight switch is in the off or running lights only position, this will not pull out. I reviewed the elect. diagram but it does not show and addition circuit for the pull switch functionality?
View 4 Replies
I have a pedal pulsation, steering wheel shimmy, and pull to the right when the brakes are applied in my truck. It is a 2009 F250 4x4 gas V8. I just replaced the pads, rotors, and calipers on the front and that's when the problem started. It definitely gets worse with speed too. I replaced the calipers because the right one had seized up and the left one looked to be on the way. There are no odd noises and the wheel bearing doesn't feel like there is any play in it. What this could be?
View 1 Replies
I know this has been discussed but I still don't understand. Hence my "dumb blonde" user name.
I just purchased a 2013 super duty f350 extended crew cab DRW.
I also purchased a 42 foot (box is 36) Goose neck Bison LQ horse trailer. Trailer weight is 12048 and tongue weight is 4468. Fully loaded I am about 18,500.
Truck pulls and stops great but it is obvious the rear suspension is sagging.
Now what? Do I need air bags? Timbren? Spring Coils? I have called several installers and they all say something different.
View 14 Replies
So I've been noticing the truck pulls left when under braking. So, I replaced the front calipers. Now, it still pulls left. When I got home I felt the discs on all corners and found three about the same, barely touchable, and the front left a little warmer. So, it seems its braking more, but its brand new. So, what should I do? They are also pulsing a little.
View 14 Replies
Just replaced break pads and rotors. Inner pad on left side was gone leading me to believe slides were not working properly. Pulled apart, cleaned and greased everything, and replaced pads and rotors. Calipers seem to be working fine. Now when I break hard, the truck pulls badly to the left. When I break softly, it seeks normal. My front end is a bit out of whack and veers just a bit to the left. Do you think this is my issue with the breaking ? I'm getting new tires and an alignment soon but was just curious.
View 3 Replies
Truck pulls to the left while braking, pretty bad. So, pulled the front right wheel off thinking the pins are stuck again as last year. Bottom pin was fine, top pin pretty gummed up but not froze so I cleaned it up good, used thin layer of the good stuff, put back together and test drove........same thing. Pulls left upon braking just as bad as before. Caliper pistons seemed fine, didn't take much to compress them either. Would a right rear cause this?
View 14 Replies
2001 Ex 7.3 4x4 with 4" lift (6" with 37" Pro Comp tires)
All new front end steering components.
All new Shocks (bilstein)
All tires properly inflated to same PSI
All new brake rotors, calipers, caliper mounts, and pads.
When under hard acceleration the vehicle pulls to the left and I have to compensate by steering to the right. Under deceleration the vehicle pulls to the right and I have to compensate by steering to the left.
I am about to change all four brake lines to Braided Stainless Steel lines, replace all leaf spring bushings with polyurethane, and install a rear anti-sway bar. I'm going through this methodically enough or am I just building a brand new truck one part at a time?
View 14 Replies
When in 4x4 and I go to do a 90 deg turn. The steering wheel pushes back to straight and seems like I have to fight it to turn the wheels. What could be causing this? I was in 4x4 Low on a dirt road at first then stopped, put it in Neutral, and turned it back to 4x4 High and then when turning in a parking lot it started doing this.
View 8 Replies
I put on a new set of tires (X Radial) at Sams Club with installation plan which includes balancing. I also brought the car to the dealer to have alignment (front I guess) done. The car goes a straight line no matter what except it always pulls left if I release the steering wheel when I brake from a high speed.
View 7 Replies
I have a 2002 F350 4x4 diesel. When I brake it pulls to the right momentarily then straightens out almost immediately. I've heard that this can be caused by bad ball joints, but I just had all four replaced less than a 15,000 miles ago, and I keep them greased regularly(every oil change). The rotors are a bit warped, but would that cause only a momentary pull? Other than that the brakes are good. I'm sure that the shocks are due for replacement. Tire wear/pressure is good. I had an alignment when the ball joints were replaced.
View 5 Replies
02-F150-4.2L-102k. Truck was rolling down the road at approx. 35 to 40 mph. A speed bump/table appeared out of nowhere and was hit before beeing seen. Immediately since this event, the truck pulls to the left while applying the brakes. It pulls very hard and is fine while rolling down the road. Is there some damaged steering component or did one of the calipers go out from the jolt?
View 4 Replies
I have 2 F-350 4x4's and they both wander back and forth when driving. They feel like they don't have enough caster. One is a 2000 V-10 extended cab with 8 foot bed. The other is a 2015 6.7 diesel crew cab with 8 foot bed.
I have driven the 2000 for so many years that I have grown use to the very slight sawing of the wheel to keep the rig straight. When my wife got her 2015 it does the same thing. The 2000 is leaf spring and the 2015 is coil spring. This bothered me when I first got the 2000 (used) but I just figured it was part of
the charm of a big truck.
I know I could put a caster shim in the 2000 but there must be a better way to solve the problem. Both are stock, no lift and no heavy winch or stuff.
View 6 Replies
Could my strut replacement have anything to do with my 2009 pulling left when I brake.
View 6 Replies
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
View 10 Replies
I have an 03 F350 4x4 dually. Was pulling hard left at low speed when braking (front). Replaced pads, calipers, rotors, hoses and tires. Still the same problem. You can feel the abs activate right before it almost locks up the left front brake (basically will pull the steering wheel out of my hand). BTW the abs light does not come on.
View 2 Replies
I have a 1997 Ram 1500 when I apply the brakes the truck pulls to the left for a spit second then goes straight.
Example: doing about 40 MPH take hands off the wheel and slam on the brakes, truck pulls immediately to left, like I did a quick lane change then goes straight.
About a month ago I replaced a section of brake line going to left rear wheel.
View 3 Replies
