Ford Super Duty (1999-2016) :: Pulls To The Left When Push The Brakes
Aug 13, 2014
My 2012 f350 6 lift when I push the brakes it pulls to the left kinda bad and the steering wheel is off to the right..
View 4 Replies
Aug 13, 2014
Advertisement
Ford Super Duty (1999-2016) :: 2003 F250 - Truck Pulls To Right When Driving And Pulls To Left On Braking
My 2003 F250 6.0 pulls to the right when driving at any speed. In order to keep it going straight the steering wheel must be slightly tilted to the left, not much but a little. When the brakes are applied hard it will go to the left slightly if you are not holding the wheel good. Neither of these are terrible, just a nuisance. I'm worried about uneven tire wear too. One front wheel bearing was replaced a few weeks ago. It had this problem before that and still does after. Does this sound like an alignment or maybe something more?
View 13 RepliesFord Super Duty (1999-2016) :: Pulls To Left While Brake Applied - Piston?
Well just called it quits from working on the truck tonight. Had some issues with my brakes going to the floor and pulling to the right some, so I went to auto zone and bought all new pads. Didn't think it was time yet because I just replaced the rotors, pads, calipers, maybe 20,000 miles ago. When I got home and everything pulled apart I looked at the pads on the truck and they still had 60% life. I looked closely and noticed that the guider pins on the caliper bracket (front drivers side) were seized. I figured this is what was causing my truck to pull. Looked on the passenger side and it looked similar. Went back to auto zone and returned the pads and bought new brackets for both sides. I got the drivers side replaced and working and all seemed well. I got to the passenger and had a hell of a time getting the pistons on the caliper to compress so I could get it off. Once I finally got it, I noticed the pins on that side were not seized. I bought 2 sets of guider pins so I took the old ones out and greased up the new ones and installed them. Put everything back together and took the truck for a drive. Everything seemed normal at first, but once I got on the highway and hit the brakes, my truck pulled to the left. HARD.. Im assuming this is because of the pistons on the passenger side caliper I was having a problem with, not having the piston compress all the way causing my truck to pull. While I was looking at the caliper, I also noticed what '"looked" like a grease fitting, and also a bleeder valve a few inches away from it. Am I crazy, or is that fitting for bleeding the brake lines also...?
View 5 RepliesFord Super Duty (1999-2016) :: F250 Pulls To The Left When Driving / Front Outer Tie Rod Bad
1999 F250 SD 4x4 7.3 PSD ... My truck has 198K miles on it. It pulls to the left as I drive it. So I took it to a shop to have the alignment checked. They told me that the front outer tie rod was bad and needed to be replaced. And of course they said they needed to put in a set of caster camber bushings to do the alignment. They quoted $400 to change the tie rod out. I said I would do that. They gave me the print out from the alignment but reading it the only thing that was out was the toe. Left tire was toe out and the right tire was toe in, which to me would cause it to pull to the left.
I got under the truck and the steering link, piece that goes from steering box to right side/tie rod, is not tight...I can move it up and down and it clunks when I roll it up. I have a clunking noise when I drive it and go over bumps also. Could this be the clunking noise? Also, if I replaced the ends of the steering link, that would tighten up but possibly push the steering back to the right some to straighten out the tires? I have read alot of threads talking about the clunking being tied to the sway bar bushings being bad but the clunking I get by rolling the steering link up and down sounds alot like the noise I am hearing.
Also, when looking at the axles where they go into the knuckle, there is a loose plastic ring on both sides. Is this part of the dust shield or an oil seal?
Ford Super Duty (1999-2016) :: 2009 F250 - Pulls Right When Brakes Applied?
I have a pedal pulsation, steering wheel shimmy, and pull to the right when the brakes are applied in my truck. It is a 2009 F250 4x4 gas V8. I just replaced the pads, rotors, and calipers on the front and that's when the problem started. It definitely gets worse with speed too. I replaced the calipers because the right one had seized up and the left one looked to be on the way. There are no odd noises and the wheel bearing doesn't feel like there is any play in it. What this could be?
View 1 RepliesFord Super Duty (1999-2016) :: 2011 F350 - Clanking Noise - Truck Pulls To The Left
Well, I tried this Death Wobble Kit on my Ford F350 Super Duty from a company called WC Motorsports. Had it installed at a Ford Dealership. DO NOT BUY this kit. Missing parts right out of the box. Also makes a horrible clanking noise after install. Piece of junk. Possible fix to one problem only to have multiple other problems:
1. Clanking Noise
2. Truck pulls to the left
3. Have to cut the factory subframe. (Never a good idea)
4. Changes the degree (not recommended by Ford)
Ford Super Duty (1999-2016) :: Brakes Pulling To Left?
My Superduty has been pulling to the left when I hit the brakes for a few months now. In the past it's done it, like within a year or two after buying it brand-new off the lot, but that was because one brake pad had rusted itself to the bracket and was not doing a darn thing. Once or twice more, it was a stuck caliper pin, which was quite obvious when working on it.
Last year, around August, I replaced the rotors and pads with Advanced Auto parts stuff. Rotors are still great, pads look brand-new, and it wasn't pulling up until the past month or two.
But this most recent pulling has been a problem that I can't find. It's not the pins, it's not the pads, and now I find out, it wasn't the calipers
This past weekend I went so far as to replace the calipers with Napa rebuilt "semi-loaded" calipers (all hardware and pins and bracket, except for the pads) and pressure-bleed the entire system. The old fluid was green, not black, but now that it's been bled, the pedal is a bit firmer than it was.
I wasn't going to replace the calipers without checking them first, but I broke both bleed nipples off and I wasn't about to wrestle with an easy-out and try to get the darn things out. Per side, rebuilt caliper with hardware and bracket, can't go wrong. (Checking the calipers would have involved using a C-clamp to compress the caliper slightly, then backing off the C-clamp - if the pistons come back out a slight degree, they are free and the seals are still "grabby" and resilient).
While bleeding it, I saw a piece of black crud (rubber?) about 2-3mm in size come out of the left side. Didn't think much of it, figured it was just built up crud from somewhere.
Today, the first commute after doing the calipers and bleeding, it's still pulling just like it was before the calipers. However, I did notice at one point when I hit them, they pulled like they normally do, but seemed to go straight a few seconds into it. It does seem that if I keep my foot on the brake, the pulling is much less after the initial second or two, but if I stab them again, it pulls like crazy.
And by "pull" I mean the steering wheel actually moves in my hand. So with that in mind, it's actually a front-brake problem. If it was the rears, the wheel wouldn't pull like it does, and if it was something loose in the suspension, I would have found it already after checking everything, and it again, wouldn't pull the steering wheel like that.
Now, given that black piece of whatever that came out of the left side, I'm beginning to wonder... if it was rubber from the inside of the hose.
Is the right brake hose causing the pulling because it's coming apart just like the left one might be?
I've gone over and over this in my head this morning, and thought about the ABS unit possibly dumping pressure from the right because of a leaky valve (see side note below), but I would think that once the pedal stab was over, it would even out and not pull at all.
However, this thing pulls left quite a bit, even after the pedal has been held down for quite some time. Usually. Sometimes, it subsides and doesn't pull. But mostly it does no matter what I do, keep pressure on the pedal, let up and reapply, whatever.
Does this really sound like a bad hose? It's intermittent, but usually pulls like 90% of the time.
Side note: The ABS unit in my truck, and most Fords of the time (not sure about later than 2004 or so) is a Kelsey-Hayes three-channel unit like this:
Kelsey-Hayes RWAL Antilock Brakes
It's the same system found in Chevy Suburbans and light-trucks, which I have worked on before and know a bit about.
In my case, it can't be a dump valve leaking, because it would effect pedal-height and not PULL to one side like it does. The only way that could happen is if the isolation valve was closed, AND the dump valve were leaking at the same time.
I haven't, however, gotten the ABS to activate just to see if it changes anything. On my way home tonight I will see if I can find some dirt or sand and get it going
Ford Super Duty (1999-2016) :: 2008 F250 - Left Rear Brakes Hanging Up
Took truck out for a ride and stopped for gas. I smelled Brakes and upon inspection found the left rear brake pads were not releasing. Any take on what could be holding it? 2008 F-250.
View 10 RepliesFord Super Duty (1999-2016) :: 2012 F250 Truck Would Pull Left When Brakes Applied
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
Ford Super Duty (1999-2016) :: 2006 F350 6.0L Wheel Pulls When Turning In 4x4
When in 4x4 and I go to do a 90 deg turn. The steering wheel pushes back to straight and seems like I have to fight it to turn the wheels. What could be causing this? I was in 4x4 Low on a dirt road at first then stopped, put it in Neutral, and turned it back to 4x4 High and then when turning in a parking lot it started doing this.
View 8 RepliesFord Super Duty (1999-2016) :: F250 7.3L Diesel - Headlight Switch Pulls Out
When you turn the headlight switch to the headlight on position, you can pull it out exhibiting a positive click as if it is an additional switch for maybe optional fog lights. If the headlight switch is in the off or running lights only position, this will not pull out. I reviewed the elect. diagram but it does not show and addition circuit for the pull switch functionality?
View 4 RepliesFord Super Duty (1999-2016) :: Truck Pulls And Stops Great But Rear Suspension Is Sagging
I know this has been discussed but I still don't understand. Hence my "dumb blonde" user name.
I just purchased a 2013 super duty f350 extended crew cab DRW.
I also purchased a 42 foot (box is 36) Goose neck Bison LQ horse trailer. Trailer weight is 12048 and tongue weight is 4468. Fully loaded I am about 18,500.
Truck pulls and stops great but it is obvious the rear suspension is sagging.
Now what? Do I need air bags? Timbren? Spring Coils? I have called several installers and they all say something different.
Ford Super Duty (1999-2016) :: Ticking Noise Coming From Right Side When Push The Accelerator
2002 Ford F-250 5.4l ... What is the difference in sound between a lifter tick and an exhaust leak? I have a ticking noise, almost sounds more like a puff of air noise, it only makes the noise when I push the accelerator and is coming from the right side. Noise is most noticeable if I put my head under the passenger side front fender. I am guessing I have an exhaust leak somewhere between the heads at cat but just wondering about the difference in sound. I'd think if it were the lifters they would tick at idle, right? The truck sounds great at idle (after doing a tune up) I just want to get rid of this annoying tick when I accelerate.
View 3 RepliesFord Super Duty (1999-2016) :: Suspension Is Too Stiff To Push Down / Shudder At Freeway Speeds
I have a 2006 F250 Lariat CC FX4. I bought the truck with 68,000 miles about 3 months ago. This is my first 4WD and I'm wondering if I need shocks.
I know how to check on a car but this suspension is too stiff to push down a corner so how do you test? Or do you just go by the age? At freeway speeds when I hit a bump I get a bit of a shudder that makes me wonder if the axle is hopping.
If I were to replace them are the Rancho shocks OK for a replacement? I will spend very little time off road and mostly use this truck for boat towing and hope to buy a travel trailer down the road.
Ford Super Duty (1999-2016) :: Dead Space Area When Push The Brake Pedal Forward
My question is this...when my foot makes contact with the brake pedal there is about a quarter or half inch of "space" where I can push the pedal forward before you can feel whatever the pedal pushes against make contact and begin applying braking.
This dead space area will always activate the brake lighting but until you reach that next part under the dash somewhere no braking occurs.
I am quite used to driving my 2010 and this doesn't occur....can not remember if the 99 has always done that and i just realized it or if this is a new issue.
Brakes and stops great with and without load. No issues otherwise. Pedal pops out quickly and normally when taking your foot off.
Ford Super Duty (1999-2016) :: 2009 F250 4x4 - Rattling When Push The Clutch Pedal To The Floor?
My stock 2009 ford f250xl 4x4 with a 5.4 and 6 speed has been giving me a weird sound lately started about a month ago and only happens on a cold start situation meaning if it sits over night it will do the sound. the sound goes away after 3-5 min of warm up in my driveway, the sound happens when i push the clutch pedal to the floor. it has no pronounced abnormal sounds through out the rest of the day when its hot which perplexes me, check out the vid on my u tube site for a sound of it.
MAH00111 - YouTube
MAH00115 - YouTube
Ford Super Duty (1999-2016) :: 2001 F350 - Parking Brake Pedal Is Extremely Hard To Push
I have a 2001 F-350 Diesel 4x4 crew cab 8ft bed dually 7.3 diesel 6 speed. The issue is that the parking brake pedal is extremely hard to push. One day it pushed down and ratcheted into a locked position as normal and the next day I couldn't push it more than an inch down. I have rear disc brakes with internal drums in the rotors for the parking brake assembly. I replaced the shoes and hardware (which were fine) and I still have the same issue. I removed the front single cable from where it splits into the two rear ones and the foot pedal depresses smoothly and with the touch of a finger with no load on it. What else is it? The only other thing is one of the rear cables unless I am missing something?
View 5 RepliesFord Super Duty (1999-2016) :: 2000 - Rear Brakes With More Power Than Front Brakes
I use a bottle hanging like an I.V. drip to flush the Brake Fluid in all my cars. I can pump all the old fluid out, as well as the air. My Superduty 7.3 has a good solid brake pedal after the flush. It seems to me the rear brakes handle 60% of the stopping load. Its been like this for so long I'm not sure if it's ever been different. i then go to a gravel or wet road and test the rear abs, and it seems o work, but definitely has a squirrely feel. I did some strong pavement stops with speed, and it stops, no skidding. Is that the way it should be?
View 14 RepliesFord Super Duty (1999-2016) :: Clicking Sound In Front Left When Make Sharp Turns To The Left And Hit Small Bumps
2004 PSD 4x4 72k. I thought I would be proactive so I bought the front ball joints and have plans to install them but recently I starting hearing (and feeling) a clicking sound in the front LEFT when I make sharp turns to the left and hit small bumps now and again. I jacked up the front end and am able to get 1/4" of movement front to back (top to bottom so not steering) in the wheel.
I narrowed it down to the hub. I took it apart and it is most likely a sealed unit so no adjustment is possible....that I can see.I pulled out the locking hub and got as far as I can to know there is not an adjustment. Need to confirm that it indeed is a sealed bearing and if so what are the part number(s) I may need to repair it.
Ford - F150 :: Truck Pulls To The Left While Applying The Brakes
02-F150-4.2L-102k. Truck was rolling down the road at approx. 35 to 40 mph. A speed bump/table appeared out of nowhere and was hit before beeing seen. Immediately since this event, the truck pulls to the left while applying the brakes. It pulls very hard and is fine while rolling down the road. Is there some damaged steering component or did one of the calipers go out from the jolt?
View 4 RepliesFord Brakes/Suspension :: Truck Badly Pulls Left When Braking Hard
Just replaced break pads and rotors. Inner pad on left side was gone leading me to believe slides were not working properly. Pulled apart, cleaned and greased everything, and replaced pads and rotors. Calipers seem to be working fine. Now when I break hard, the truck pulls badly to the left. When I break softly, it seeks normal. My front end is a bit out of whack and veers just a bit to the left. Do you think this is my issue with the breaking ? I'm getting new tires and an alignment soon but was just curious.
View 3 Replies