Ford Super Duty (1999-2016) :: 2006 F450 - Delay In Cranking For About 20 Seconds
Dec 10, 2013
I have a 2006 F450 6.0 Super Heavy Duty. The Problem that I am having is when I turn the key it wont crank over. In order for it to start I have to hold the key in the crank position (like i am trying to start it) for about 20+ seconds, and then it will start cranking over. After it cranks over it starts just fine no problems. This only occurs when I start the truck up for the first time each day. After the initial start of the day its fine. (FYI I turn the ignition to the on position and just let it set it still takes me turning the key to the crank position and holding it 20+ seconds).
View 5 Replies
Advertisement
Well it's been an ongoing problem with my 4r100, but last week it all come to a point. Reverse delay is getting to near 10seconds then abruptly engages. My 1-2 shift is so soft I have to look down and see my tach to make sure it shifted up. I now have trans squeal during ever shift including OD. Also have a loud screech that gets louder the faster you go, BUT the old girl is still moving the truck and oddly the fluid isn't burnt looking or smells burnt? That's one has me puzzled...
So Tuesday after work I'm pulling the transmission (in the driveway) and bringing it to the shop Thursday. Getting a billet steel converter, having all the planetary gears upgraded to six and four pinion, one way sprag will now be solid steel instead of the plastic one Ford put there, all the bearings will be upgraded to Torrington, I'll have the 45 roller sprag bearing upgrade as well as the 17 roller for reverse, I'm going with Borg Warner and Kolen steels, new solenoid pack.
I'm having the pump pump machined and sonnex upgrades done to it, spiral snap ring on OD piston, case will be machines not hand resurfaced, reverse gear plastic washers will be removed and the gear is getting machined for a Torrington bearing and steel spacer, clutch drum will be machined for a 360 spiral clip, locking snap ring on the OD piston, center support will have some machine work done to it, and I'm having the forward drum plug removed and the hole will be tapped for a steel plug.
View 14 Replies
I have a 08 6.4l F250SD. At 127k miles, it has been a great truck. All service has been performed by dealer. When I shift from Park into drive there is a 3-5 second delay, and when it drops into drive the truck rocks. Once driving there are no shift issues. Into reverse there are no issues.
View 14 Replies
Ok I am getting a (6R140) transmission behaviour every morning drive or later in the day after the transmission cools down. I am experiencing a 2-3 second delay of engagement when putting truck in Reverse. This happens EVERY time whether transmission is cold or warmed up. I am also having very hard/harsh shift fares going into 3rd gear and 5th gear with the 3rd gear being the worse of the two. Also experiencing these hard/harsh shift when downshifting as well.
I took the truck to my local dealer and I let it sit over night in their lot so they could experience it at its worst after sitting all night. They definitely recognized the issue. But since it wasn't throwing and codes. I find this an unacceptable answer.
I brought to their attention that this issue is well documented online and a lot are having success with performing TSB 11-7-10 (replacing solenoids) They looked it up and said my truck doesn't apply to TSB because of the build date. My window sticker and VIN # implies the truck was built 10-11-2010. Which from my understanding, does fall under the required TSB. None the less, I insisted that I know I'm out of warranty and I will just pay to have this TSB performed. They refused.
What should I do? I know everyday I run my truck with this issue it is decreasing the reliability of this transmission and it will most likely end with a full transmission replacement.
View 5 Replies
I am working on a 2006 f450 6.0l. My problem is when I take key out of the ignition the power stays on in truck. Radio stays on and windows. I swapped out relays checked door jam switch I am stuck. Looking for wiring diagrams so I can trace the wire.
View 5 Replies
My 06 f350 power stroke has a viper 2way remote starter.
When I try to start it when the truck is cold it doesn't crank long enough for it to start the truck. It will try 3 times when I hit the start button and normally won't go. It almost starts most times but stops cranking right before it starts. This is driving me nuts.
I just tried 3 times to start the truck and it in ally went on the 8th time trying to crank.
View 12 Replies
Have a 2006 F350 5.4l that is mainly used as a plow truck. I drive it at least once a week when not plowing just to make sure it runs ok, etc. Only put on about 2,500 miles per year. Keep it in good repair - not by me, but by the dealer or mechanics.
Problem - last two times I started it, it started ok but runs real rough for about ten seconds. Sounds like the engine is going to die. After about ten seconds, it "catches" and runs normal. Have no problems when driving it. If I restart it, it doesn't do this, so it seems to only happen when the engine is cold.
Battery was brand new back in Sept. All plugs were replaced maybe 3 years ago, as was the cat converter and muffler. Run non-ethanol fuel. What might be causing it before I bring it in.
View 6 Replies
I have a 1999 F450 that was bought new as a cab and chassis. The truck belonged to my dad who passed away two years ago and now I have it. I am wondering if it has 4.30 or 4.88 gears. The rear end is huge! It has an aluminum cover with cooling fins on it, not sure if they both had that or not. I looked online and I think it said all cab and chassis had 4.88?
View 10 Replies
As I am driving everything goes dead radio, windows, dash, alarms, everything then turns on a usually 30 seconds later. is it a ground? is it a sensor that's getting to warm? is it a loose wire? where should I start??
View 6 Replies
Ok just bought this truck ran fine. Put a sct tuner on that the truck came with and some how got the egr turned on. It had a egr delete so it was smoking and finally found it out that it had turned on but fixed it. Now we have another problem, it will start up and run fine and about 45 seconds it will start running rough and go into a limp mode. It will run rough and starts to die slowly and when it starts to die there is no throttle at all.
View 4 Replies
My 99 f450 7.3 runs bad on first start of day. I checked the codes 3 codes p0475, p0470 and p1247. Now here is what I tried I plugged it in over night and it will start and run as should the next morning with out side temp 47. Drove the truck late yesterday evening didn't plug up tried it this morning with a outside temp of 47 truck starts but missing and like of power. My problem seems to be temp related. Will low boost pressure cause this problem what do I need to do?
View 4 Replies
Purchased new 2016 450 platinum. Has less than 800 miles on it and has a terrible vibration between 70-80 mph... Already have taken to dealer who stated there was a wheel out of balance and that they fixed the issue. But still present.
View 14 Replies
I have a 99 F450. I have an ABS light on. No codes (at least not that my code reader can pickup), but I am also not having any issues. Brakes work fine. What to swap out or where to look?
View 7 Replies
Can an f-450 with a blown 6.4 diesel received an transplant from an f-350 V-10.
How much would need to go over from the f-350 to f-450?
View 1 Replies
I have an 02 F450 with a dump bed an just under 45,000 miles (was barley used by the first owner). This maybe unrelated to my problem but is worth mentioning. This past week I noticed a small puddle where I had previously parked at a customers house so I checked the oil. I was about 2 quarts low. I followed the oil trail up and found a pool in the valley. One of the high pressure lines were loose and the seal was chewed up so I replaced it and tightened it. No more oil leak.
Now my new problem. Two days later, after about 45 minutes on the interstate driving about 75 mph the truck started to rapidly lose power as if it was running out of fuel. I heard a loud ticking sound coming from the engine and the more I tried to accelerate the worse it got. I pulled over and the truck stalled. I thought that maybe my fuel gauge had crapped the bed on me because it still read a little over 1/4 tank. I called a buddy and got more deisal in it and it started right up. We'll after about 5 minutes of 60 mph it started to happen again. So to fast forward... I opened up the tank and found the the strainer had crumbled in the bottom of the tank.
So I cleaned out the screens in the sending unit and replaced the strainer, replaced the fuel filter, and reverse blew out the lines. I read about checking the hpop reservoir for oil and it is present. So to sum up, as long as I stay under 60mph or so I can get about 5 minutes of run time before the truck starts to stutter and stumble. If I shut it off for about 5minutes I can go back up to 60 again but it the cycle continues. 5 on and 5 off. If I start the truck after say 30 seconds after shutting it off it sounds like it's going to die and has no power at all. I have worked on a lot of vehicles but none with anything like this and this is my first deisal. What do I do to get this beast back to normal?
View 3 Replies
I have a 1999 F450 Diesel dump truck. Automatic. The problem that I have is that the truck will drive VERY SLOWLY while the rps go up.
You can hear the engine revving up, and a strong air sound when doing so (do not know if intake or exhaust, but its like a strong wind sound. And not like a hiss, so I do not think its a vacuum leak).
The transmission goes through gears fine, but it does the rev up thing through every gear. So I am wondering if something like the torque converter might be broken or slipping.
For example, if you go with the loaded truck up a hill, you have to really push it to keep any type of speed. Or when you get off a red light.
When I bought it used, I thought that it might have a really short final gear. But that would not explain the high RPM and no push.....
No codes at all.
View 10 Replies
It's a 2004 F450 super duty, no power steering. The pump seems to function, no pump whine. I was told that it may be the steering gear box it's self.
View 2 Replies
I've got a 2004 f450 6.0 diesel. This thing will start and run great when it's cold. Then when it gets to operating temp, around 190, it will shut down. This is getting worse and worse.
A little history, it was doing this for awhile and a had a few other issues before this. Puking antifreeze, stiction issues, and bad exhaust manifold. Since it wasn't running great I figured why not pull that cab and take care of these issues.
As of last week she got new head gaskets, new exhaust manifold, new injectors, updated standpipes, updated dummy plugs, new o rings on hpop (yellow on the bottom), and a new pipe to the oil pump. I have the old style it's not the stc fitting.
All that work, it still stalls when warm. I monitor with a scan gauge 2. ( Big diesel tech Ron's fan) ...
First thing, give here two second crank start right up, runs better then ever. Gets to operating temp, rev it up, then stalls. Ipc is at 85% ipr gets up to 180 psi.
Unplug ipc, shows 765 psi on the ipr still no start. Put shop air to her and I can't hear any leaks ( probably 15 mins or so).
View 4 Replies
I have a F450 that I bought a few months ago and have been having trouble with Fuse location 35 blowing. When I purchased the truck the 4x4, tow/haul, and reverse sensing system worked because I had to use it loading and unloading my boat this fall. Since then the snow fell and when I tried to put it into 4x4 I noticed it would not. I checked the passenger compartment fuse (loc. 35) and it was blown.
So I figured it was an easy fix, changed fuse, and it immediately blew again, and again. So then I started checking components related to fuse 35. First i checked the tow/haul switch in the shift lever and thought it was that, so I replaced it, and it still blew fuses. Next, I unplugged the reverse sensing systems and still blew the fuse. Next, I turned my attention to the transfer case shift motor. I replaced it and still blew fuse. So at this point I am stumped.
It is probably worth mentioning that when I replace the fuse initially and turn the key over, all systems work. I can switch the dash switch to 4x4 and it will shift, also the illumination light on the dash comes on. I can also toggle the tow/haul switch and the illumination light on the dash comes on as well. The reverse sensing system also works as well and the light in the switch works as well.
Now and important thing to note is that it seems to hold the fuse for a minute or more with the engine off/ key on, when I start the engine, it works briefly but then the fuse blows. I am not a service tech. by any means but am very comfortable under the hood and have a fairly good understanding of electrical components and their operation. It seems to me that somewhere in the circuit that there is a short to ground or a faulty component(module) or something completely different.
The fact that it takes a minute or so to blow the fuse as compared to an immediate blow when the key is cycled to power on. I would like to fix this myself as with anything I do, I like to educate myself through diagnosis/repair. The last piece of information with mentioning is that before I purchased the truck(30,000 miles ago) it had a factory reman engine installed at a ford dealer. If worse comes to worse I will have to take it to a Ford dealership for service but would like to keep it in house if I could!
View 4 Replies
I tried to take my tailgate off my 08 F-450 today.
Did it the same as every tailgate Ive taken off in the last 20 years...........it wouldn't come.
Is there a trick to it?
View 6 Replies
Im working on a 03 f-450 that has a front end vibration, it starts when you hit 25 mph and its a humming / vibration that seems more to the passenger side than the drivers side. You can also hear it decrease when you come down in speed and it dissappears below 25 mph. Its a 2003 F-450 CC 4x4 DRW with the v-10.
View 7 Replies
