Ford Super Duty (1999-2016) :: Reverse Delay Is Getting To Near 10 Seconds Then Abruptly Engage
Jun 12, 2016
Well it's been an ongoing problem with my 4r100, but last week it all come to a point. Reverse delay is getting to near 10seconds then abruptly engages. My 1-2 shift is so soft I have to look down and see my tach to make sure it shifted up. I now have trans squeal during ever shift including OD. Also have a loud screech that gets louder the faster you go, BUT the old girl is still moving the truck and oddly the fluid isn't burnt looking or smells burnt? That's one has me puzzled...
So Tuesday after work I'm pulling the transmission (in the driveway) and bringing it to the shop Thursday. Getting a billet steel converter, having all the planetary gears upgraded to six and four pinion, one way sprag will now be solid steel instead of the plastic one Ford put there, all the bearings will be upgraded to Torrington, I'll have the 45 roller sprag bearing upgrade as well as the 17 roller for reverse, I'm going with Borg Warner and Kolen steels, new solenoid pack.
I'm having the pump pump machined and sonnex upgrades done to it, spiral snap ring on OD piston, case will be machines not hand resurfaced, reverse gear plastic washers will be removed and the gear is getting machined for a Torrington bearing and steel spacer, clutch drum will be machined for a 360 spiral clip, locking snap ring on the OD piston, center support will have some machine work done to it, and I'm having the forward drum plug removed and the hole will be tapped for a steel plug.
View 14 Replies
Advertisement
Ok I am getting a (6R140) transmission behaviour every morning drive or later in the day after the transmission cools down. I am experiencing a 2-3 second delay of engagement when putting truck in Reverse. This happens EVERY time whether transmission is cold or warmed up. I am also having very hard/harsh shift fares going into 3rd gear and 5th gear with the 3rd gear being the worse of the two. Also experiencing these hard/harsh shift when downshifting as well.
I took the truck to my local dealer and I let it sit over night in their lot so they could experience it at its worst after sitting all night. They definitely recognized the issue. But since it wasn't throwing and codes. I find this an unacceptable answer.
I brought to their attention that this issue is well documented online and a lot are having success with performing TSB 11-7-10 (replacing solenoids) They looked it up and said my truck doesn't apply to TSB because of the build date. My window sticker and VIN # implies the truck was built 10-11-2010. Which from my understanding, does fall under the required TSB. None the less, I insisted that I know I'm out of warranty and I will just pay to have this TSB performed. They refused.
What should I do? I know everyday I run my truck with this issue it is decreasing the reliability of this transmission and it will most likely end with a full transmission replacement.
View 5 Replies
2015 F-250 4X4 CC gas truck. 6R140 Transmission..
My truck has 6500 miles on it and since day one when I put my shifter in (D) there is a 3-4 sec delay in the transmission to engage every morning when I start out, rest of the time there is no delay even when the truck sits all day at work (about 9 hours). I have read in 2011 (?) that the transmission was loosening it's prime and would cause this problem, so how it's got me thinking.
View 9 Replies
I have a 2006 F450 6.0 Super Heavy Duty. The Problem that I am having is when I turn the key it wont crank over. In order for it to start I have to hold the key in the crank position (like i am trying to start it) for about 20+ seconds, and then it will start cranking over. After it cranks over it starts just fine no problems. This only occurs when I start the truck up for the first time each day. After the initial start of the day its fine. (FYI I turn the ignition to the on position and just let it set it still takes me turning the key to the crank position and holding it 20+ seconds).
View 5 Replies
I have a 08 6.4l F250SD. At 127k miles, it has been a great truck. All service has been performed by dealer. When I shift from Park into drive there is a 3-5 second delay, and when it drops into drive the truck rocks. Once driving there are no shift issues. Into reverse there are no issues.
View 14 Replies
Today I noticed that our 5R110 was delaying slightly when shifting from drive to reverse. It was probably about a 1-2 second delay but it replicated itself twice in a row. There was no delay going from reverse to drive. It is just an engagement delay. We are running a Superchips Heavy Tow tune on the truck, it is a 2006 6.0 Powerstroke.
View 4 Replies
I have an automatic 2004 f150 fx4 with a 5.4 engine. I just bought the truck and noticed the other day that when I shift into reverse, there is a 1-2 second delay. Sometimes it will shift quicker than other times. Drive seems to be a little more swift I think. Everything seems to run smooth and the shifting is very smoot other than the delay. Is this normal or what could be some of the causes. The previous owner has the ATF changed this pst summer and it looks and smells fine other than maybe having to much fluid.
View 2 Replies
Still having issues with the transmission on my 05 F350. I posted before that it would take a few seconds to go into drive or reverse. The fixes were to change filters and do hot flush. I had the dealer do a hot flush, and then I put about 1000 miles on it. That didn't seem to fix anything, so I went back in and asked for more info. They did not change the filters. I thought they did, but found out they did not after the fact, so I decided to change the filters myself.
The interior filter was easy to change. The fluid was clean, and the magnet had shavings on it but nothing that seemed extraordinary. The exterior filter is impossible to get off. I reviewed posts on here before trying, so first was the impact wrench, then the pipe wrench, then the pipe wrench with a block wedged in to keep the thing from bending, still no luck. The cast nut broke off well before the pipe wrench came out of the drawer. How to get that thing off. I read on here somewhere that no fluid goes through that until 180 degrees, is that correct?
Scanguage says it rarely goes over 160, except for last evening when I was stuck in traffic. It went to 187, with ECT at 208. During this period, traveling under 40 most of the time, the transmission was shifting erratically, to the point I wanted to pull over and allow it to cool down. But traffic broke free, speed went up, and temps went down. Shifting returned to normal, except when trying to engage drive or reverse. The 3-4 second delay persists at any temp, and there doesn't seem to be any slippage. Just delayed and sometimes hard engagements. I'm at a loss for whats wrong.
View 1 Replies
I have a 2006 F250 Lariat super Duty / 6.0 L engine / 143000+ miles / once started and transmission shifted into drive it takes 5 seconds or more for it to engage hard or if I build up the RMS then it jumps into gear hard, after it gets going it feels like I am driving on a washboard until it get warmed up good 10 mile or so. Is it the transmission filter and if so which one, I understand there is a small one on the outside of the transmission if so where? I can't find it.
View 14 Replies
I have a 1999 F250 super duty that blew a front seal on the transmission two weeks ago. I sent it to a shop and they replaced the seal, and torque converter. However when they put it back in it will not engage in drive or reverse. After working on it several days we replaced the transmission with another one from a service company. This replacement came with a 90 day warranty. However once it was installed it does the same thing and will not engage in drive, or reverse. I am not sure what is going on but with two doing the same thing it makes me thing maybe electrical or something else.
View 1 Replies
I have a delay when I put my truck into gear. It only happens when I have turned the truck back on. It happens in forward as well as reverse. What is causing this? Syncros?
View 8 Replies
I have a 2000, F250, 7.3, automatic with 220,500 miles. When I purchased my truck used in 2008 (173,000 miles), i had the transmission rebulit by a ford dealership. Okay my problem is now that the weather is cooler here in Texas, when I back out of my parking spot in the morning, it takes several seconds for my truck to engage into drive. The rest of the day it works fine, only first thing in the morning. No problems driving (shifting) during the day.
View 3 Replies
Ok so long story short, my Viper 2 way alarm, instead of the brain being wired to each of the 4 doors individually, the installer ran 1 wire to the dome light. seems to work fine as far as arming/disarming/locking/unlocking, but since the dome light stays on for 10 seconds or whatever after the door is shut.
When I arm it, the 2 way remote says "door open" because the light is still on so it thinks a door is open. this eventually times out and all the sensors arm, but theres a long delay. it arms fine and no alerts pop up if i lock the doors first from the outside keypad on the door, making the lights go off, then hit arm on the viper, and everything is good to go.
can i change it so no matter what, as SOON as i shut the door, the light goes off? i want there to be NO delay, if possible. if not, i may need to just have the installer run a wire to each door and take the single run to the dome light off, as it is sorta annoying to me.
View 1 Replies
On my 99 lariat the 4x4 does not engage. It's got a electric switch on the dash. The 4x4 light comes on when I turn the key on for 3 seconds. But when I turn the switch I got nothing and can't hear anything trying to engage. Where to start or how to test the switch?
View 3 Replies
What are some simple checks, my 4x4 low range does not engage, just stays in 4 hi. 2003 f350 screw v10.
View 5 Replies
So sometimes the 4x4 takes awhile to engage. Both hubs are free turning (manual to auto). Drivers side only holds a few psi of vacuum. Passengers side 20ish. All seals have been replaced. Was tested right at the nipple on drivers side front. Switching hubs from side to side didn't change anything. 2 mechanics are unsure what to do aside from take a chance at replacing the wheel bearing. It does eventually go into 4x4 but takes awhile for 4x4 to engage and light on dash to come on.
View 14 Replies
My truck: 2001 F250 V8 Triton Automatic 4x4
Problem: 4x4 won't engage
Symptoms: No dash lights....nothing happens when I turn the 4x4 switch. When I start the truck I hear what sounds like a motor (transfer case motor maybe?) trying to switch (even though my dash switch is on 2WD)... It tries three times and stops.
What I've done: Checked fuses ...they appear ok to me
I don't have a maintenance manual yet ...
The 4x4 used to work up until about 2 weeks ago. Started having a hard time getting it to go into (and out of) 4x4 and then it just stopped all together.
View 3 Replies
2008 F-250XL, 5.4L V8, 5 speed auto, 3.73 rear.
Two/haul fails to engage and does not light up dash indicator light from time to time. After 4 or 5 tries it usually will engage normally. No codes.
View 2 Replies
2005 F-250 King Ranch Diesel ... My truck when I got it the 4x4 wouldn't engage. I replace the front inner seals, and the lock outs. Still wouldn't work. Took the shift motor off and freed it up and it worked fin till today. Changed the shift motor and still nothing. This truck has been nothing but problems since I have had it and now this ... Truck is going on the market soon and would sell better if the 4x4 worked ...
View 13 Replies
How to diagnose a vacuum leak without a vacuum leak diagnostic tool.
My ESOF won't engage, AC/heat blowers default to defrost - classic symptoms. And while we can leave without AC/heat, we really need the ability to engage 4x4 low, especially as we get higher into the Andes and the roads unsmooth.
View 8 Replies
F-250 2005 XLT 5.4L 4X4. Had ford for a few years now (Escape as a personal vehicle and econoline as business vehicle). Now I'm having a little problem with 4x4. It wont engage. Worked fine last week and now nothing! I did check all the fuses and when i switch to either 4Lo or 4Hi I can hear a clicking sound behind the switch but feel like it's getting blocked or something. Tries a few time then stop...
View 14 Replies
