Ford Super Duty (1999-2016) :: 2 To 3 Seconds Delay Of Engagement When Putting Truck In Reverse
Dec 2, 2015
Ok I am getting a (6R140) transmission behaviour every morning drive or later in the day after the transmission cools down. I am experiencing a 2-3 second delay of engagement when putting truck in Reverse. This happens EVERY time whether transmission is cold or warmed up. I am also having very hard/harsh shift fares going into 3rd gear and 5th gear with the 3rd gear being the worse of the two. Also experiencing these hard/harsh shift when downshifting as well.
I took the truck to my local dealer and I let it sit over night in their lot so they could experience it at its worst after sitting all night. They definitely recognized the issue. But since it wasn't throwing and codes. I find this an unacceptable answer.
I brought to their attention that this issue is well documented online and a lot are having success with performing TSB 11-7-10 (replacing solenoids) They looked it up and said my truck doesn't apply to TSB because of the build date. My window sticker and VIN # implies the truck was built 10-11-2010. Which from my understanding, does fall under the required TSB. None the less, I insisted that I know I'm out of warranty and I will just pay to have this TSB performed. They refused.
What should I do? I know everyday I run my truck with this issue it is decreasing the reliability of this transmission and it will most likely end with a full transmission replacement.
View 5 Replies
Advertisement
Well it's been an ongoing problem with my 4r100, but last week it all come to a point. Reverse delay is getting to near 10seconds then abruptly engages. My 1-2 shift is so soft I have to look down and see my tach to make sure it shifted up. I now have trans squeal during ever shift including OD. Also have a loud screech that gets louder the faster you go, BUT the old girl is still moving the truck and oddly the fluid isn't burnt looking or smells burnt? That's one has me puzzled...
So Tuesday after work I'm pulling the transmission (in the driveway) and bringing it to the shop Thursday. Getting a billet steel converter, having all the planetary gears upgraded to six and four pinion, one way sprag will now be solid steel instead of the plastic one Ford put there, all the bearings will be upgraded to Torrington, I'll have the 45 roller sprag bearing upgrade as well as the 17 roller for reverse, I'm going with Borg Warner and Kolen steels, new solenoid pack.
I'm having the pump pump machined and sonnex upgrades done to it, spiral snap ring on OD piston, case will be machines not hand resurfaced, reverse gear plastic washers will be removed and the gear is getting machined for a Torrington bearing and steel spacer, clutch drum will be machined for a 360 spiral clip, locking snap ring on the OD piston, center support will have some machine work done to it, and I'm having the forward drum plug removed and the hole will be tapped for a steel plug.
View 14 Replies
I have a 2006 F450 6.0 Super Heavy Duty. The Problem that I am having is when I turn the key it wont crank over. In order for it to start I have to hold the key in the crank position (like i am trying to start it) for about 20+ seconds, and then it will start cranking over. After it cranks over it starts just fine no problems. This only occurs when I start the truck up for the first time each day. After the initial start of the day its fine. (FYI I turn the ignition to the on position and just let it set it still takes me turning the key to the crank position and holding it 20+ seconds).
View 5 Replies
I have a 08 6.4l F250SD. At 127k miles, it has been a great truck. All service has been performed by dealer. When I shift from Park into drive there is a 3-5 second delay, and when it drops into drive the truck rocks. Once driving there are no shift issues. Into reverse there are no issues.
View 14 Replies
Today I noticed that our 5R110 was delaying slightly when shifting from drive to reverse. It was probably about a 1-2 second delay but it replicated itself twice in a row. There was no delay going from reverse to drive. It is just an engagement delay. We are running a Superchips Heavy Tow tune on the truck, it is a 2006 6.0 Powerstroke.
View 4 Replies
I have a delay when I put my truck into gear. It only happens when I have turned the truck back on. It happens in forward as well as reverse. What is causing this? Syncros?
View 8 Replies
I recently bought a 2003 F350 super duty dually automatic transmission 6.0 deisel 4x4. The 4x4 is not working. with the hubs in auto when i flip the switch to 4x4 high nothing happens.The same with 4x4 low putting the truck in neutral. I can only find 2 fuses using the owners manual that says anything about 4x4 and both of them check out good. Also the owners manual says when i turn on the key I should see a 4x4 light and a low range light momentarily. Neither of these lights are showing up. I don't hear any clicking or any noise of any kind when trying the 4x4.It acts like an electrical issue but not sure where to start.
View 7 Replies
Simple enough the truck starts then after about 30 seconds it bogs down and dies. I am getting these codes.
705 Transmission Range Sensor Out of Position
708 Transmission Range Sensor Circuit High Input
720 Output Speed Sensor Insufficient Input
743 Torque Converter Clutch Circuit
745 Pressure Control Solenoid Malfunction
1747 Electronic Pressure Control Solenoid A- Short Circuit
Sounds to me like the converter it locked up. What do you think? Its a 5.4L
View 3 Replies
When I put the truck into reverse, sometimes the rear park assist sensors go off for no reason, sometimes they work correctly. Is there a way to narrow down which sensor it might be, or just replace the lot?
View 5 Replies
For the past month or so, probably about a half dozen times now, I will start the truck in the garage but I can't seem to get it into reverse right away. It may very well be a timing thing with me depressing the brake pedal, but I'm not so sure. I've been backing the truck out of the garage for five years and I've never had a timing issue, and I'm definitely noticing it now.
Is/was there an issue with the brake pedal as it related to putting the vehicle in gear? Could it be something going on with the brake pedal for that function? It is very sporadic, maybe once or twice a week it happens (I don't take it out that much). Trying to gather info before hitting up my dealer.
View 4 Replies
Have 2001 F-250 7.3 PSD, automatic, ESOF (had to replace the original hubs with Warns)have kept up the maintenance,oil, grease, ATF fluid & filter, truck has been virtually trouble free. About 2 weeks ago I decided to go across an area of the lawn, as I was going (in 2 wheel drive)I felt the tires spin a little so I stopped got out and locked the hubs, got back in truck turned t-case to 4 high. had to rock the truck out of a damp area but nothing really.
So I got back to where I came in at (in reverse about 100') stopped put it back in 2 wheel drive, tried to go forward, very difficult, sluggish, got back in driveway had to back the truck in, will not go forward at all now. Checked all fuses, rapped the the t-case motor, no codes. So I thought I'd move the ruck, have a winch that will pull it out by the barn, I could not even move the truck forward by pulling it with a winch. As I said have never had any problems with truck. Transmission fluid is good, clean no burnt smell.
View 14 Replies
I was driving my sons 99 f250, 7.3, today, pulled into a friends driveway, put the truck into park, turned it off and got out. 5 minutes later out of nowhere the truck jumped out of park into reverse like someone was in it stomping on the gas then the breaks then the gas, then the breaks. This truck took off in reverse with such force if there was someone behind it they would have been seriously hurt. I was parked on completely flat ground. While this was happening it sounded like it was trying to start and clicking very loud. It is an automatic.
View 3 Replies
It is a 99 F350 diesel automatic. T- case motor is good. Relays are new. All fuses are good. I have no power coming into the dash engagement switch. Bought this pickup for a backup farm truck and need the 4x4 to work.
View 6 Replies
I have a question about when my truck is in 4 wheel drive. I've read a lot of posts but couldn't find specific answers to these questions: When I take a left turn theres quite a bit of resistance and a little hopping. Also when turning in reverse its almost like the truck is getting hung up and a with resistance, something doesn't seem right. Could any of this be if only one hub is engaging? Also, when i just manually lock the hubs, I only noticed that the passenger side axle spins when I manually turn the front drive shaft.
Also this is the first time I've used the 4 wheel drive. And I recently replaced front axle u joints, as well as a double cardan joint rebuild, only issue w/ that is that is i forgot to mark the orientation where the front driveshaft bolts onto the the transfer case...so it's either on the right way or a 180 from how it was before, because I could see the original pattern.
2000 4x4 7.3 long bed ext cab, 159k
View 4 Replies
I have a 2011 F250 with the 6.2 gas engine. I have been having a problem that the dealership says there is nothing they can do and have never heard about.
After the truck sits all night I get in and drive it for 10-15 min. It gets warm and I get out turning it off. When I come back about 15-45 min later I start it up and go to leave. As I pull out and start to accelerate in first gear the truck goes to an idle for about 2-3 seconds. I push the gas pedal and get no response. After a couple of seconds it picks up wherever you have the gas pedal. If you have the pedal to the floor it jumps you forward. This is not putting on any lights and the computer is not throwing any codes. According to the dealership the computer is telling them there is nothing wrong.
This has happened 12 times in the past 6 months. It has happened since I bought the truck. I have just started documenting it as of 6 months ago. It is not something I can make it do on command. After it happens once it doesn't seem to do it again for a week or two. I have 31000 miles on the truck. The dealership has had it for 4 days now and can't seem to get it to happen for them.
View 2 Replies
Well I just bought a 2011F250 6.7 on Friday. The truck has 42000 miles when I picked it up and now has almost 42800 4 days later. I love the truck so far. But anyways its an early build so is there anything I need to look out for? I noticed today I pulled into a parking spot and went to back up and as soon as I put it in reverse the truck shook pretty bad. It did it a few times as I sat there and went from drive to reverse. Is this something that is normal?
View 9 Replies
2000 6.8 v10 F250 supper duty crew cab. 4x4 high switch's on (manual lock hubs installed) but 4x4 low will not engage. Brake input/out put tested good. Trans switch Park/"N" both test good. PCM reads switch output in all modes, (dash 4x4 selector). The only other issue I am having is the Vacuum is bad ( defrost default no blend door operation). Would vacuum loss prevent 4x4 lo range engagement (with manual hubs ) or should I go to the solenoid, relays on the case/ right fender?
View 4 Replies
I'm looking to put a 4.5" lift and 37s on my 2011 F250 which has the 6.2L gas engine and wanted some feedback from others who have the same setup. The kind of info I'm looking for is how much power did you lose, does the trans drop out of overdrive a lot on the highway, what you mpg, etc. And overall driving and performance of the truck.
View 14 Replies
I have a 2000, F250, 7.3, automatic with 220,500 miles. When I purchased my truck used in 2008 (173,000 miles), i had the transmission rebulit by a ford dealership. Okay my problem is now that the weather is cooler here in Texas, when I back out of my parking spot in the morning, it takes several seconds for my truck to engage into drive. The rest of the day it works fine, only first thing in the morning. No problems driving (shifting) during the day.
View 3 Replies
So I'm interested in putting a new steering stabilizer on my truck and am pretty set on the Rancho RS7000 series, but I am torn between getting a single OEM replacement or the full dual stabilizer kit. Single replacement? Did it make a difference? I've heard really good things about the dual kit, but obviously the price difference is huge. I don't do a ton of off-roading, but I do drive constantly on crappy city roads which can be just as bad
View 14 Replies
I'm putting new brake pas on my front and I want to know what is the best type to put on there. I ave a 2006 F-350 Dually.
View 3 Replies
