Ford Super Duty (1999-2016) :: 2006 - Got Trans Code P0752 And P2700 With Rough Shifting?
Aug 18, 2014
My truck started acting up the other day with a flashing Tow/Haul light and CEL. The codes for the transmission were P0752 and P2700. I swapped out the SSPC-A solenoid unhooked the batteries for an hour and there was no change.
I hooked up a 100lb oil pressure gauge to the 1/8"npt outlet on the side of the tranny. At startup it immediately pegged the gauge....forever, lol. The gauge is toast now. Upon starting is has oil pressure visible in the see through line of the oil pressure gauge. But....if you tap the throttle in park for a second, the line looses pressure (by seeing the oil go back toward the transmission). Without pressure, when you put it in drive, it takes about 5 seconds at idle to build pressure and engage. If you give it the slightest throttle before engagement, it won't engage.
Also, as probably expected, the transmission hunts a bit with rough shifting.
View 6 Replies
Advertisement
Just got the transmission rebuilt in my truck and other then shifting hard sometimes it has been doing great, Hooked it up to the goose neck this evening and everything was fine then went to back it up and pull it forward and after a short distance the od light was flashing and when i ran a check on it it was p0720? The transmission has less then 1000 miles on it?!?!? 1999 Ford F-250 7.3 Automatic....
View 5 Replies
The truck belongs to a very good customer of mine and is a 05 f350sd 6.0 td with 5r110 torqshift tranny. The vehicle presents with these symptoms and codes....
-there is a delay from p to r and its intermittent, sometimes it will be in a weak reverse where it wont creep unless you give it some gas, sometimes it will hit reverse hard after this. sometimes it bangs reverse
-there is a delay into drive intermittently with the same symptoms as reverse where sometimes it bangs and sometimes it will take a little throttle to get it moving
-once the trans is hot (operating temperature) it has trouble downshifting. my solus tells me sometimes it tries to start off in 3 or 5 then sometimes it will bang back down into first and almost chirp tire with little throttle input
-tow haul light will flash after several miles and then it only has 1-2-3-4 no 5-6. then the starting off symptoms get worse
-throws codes for
p0766 shift sol d performance/stuck
p2701 friction element b apply time range/performance
p2703 friction element d apply time range/performance
p0700 trans control system fault.
So far the ideas i have are as follows
replace solenoid D
direct clutch replacement and seals for corresponding drum
torque converter replacement and pump replacement
harness rub through between pcm and transmission
The truck has had similar issues a year ago. Upon testing line pressure i found it was out of spec and replaced the epc. (electronic pressure control solenoid) and this cleared most of it up . I have had the pan down many times and the fluid has not been burnt and there is little debris in the pan. nothing i would consider beyond normal wear. Tomorrow I will be dropping the pan again to inspect the magnet and fluid as well as the condition of the harness. i will post my findings at that time. I am hoping between now and then some of you will be able to point out a few possibilities to get me on the right track.
View 14 Replies
2006 E-350 Dually Ambulance Chassis with the 6.0... Approx 125000 miles.
Recently, the truck started an issue. its an every once in awhile thing but has been doing it more recently. The OD light will start flashing and the vehicle will start to have clunking in the tranny and start shifting rough. ABS kicks in making it hard to stop. Once you turn the truck off and back on, Its fine until it does it again. Im connecting to a scanner tomorrow to see if i get any codes.
View 14 Replies
Last week I hauled my camper (2000 Thor Citation @ about 10,000 lbs) to Moosehead Lake. On the trip to and from I experienced a few problems. Tow/haul was engaged all three times. Trucks got just over 90,000 mi.
1) When shifting, the truck would occasionally stutter, like a gas engine when it misfires. Seemed like it would usually happen when transitioning from a slight down hill to an up hill.
2) Once, after a long up hill pull, as it crested the top, the truck slammed into the next gear, hard.
3)Once, going down hill, the trans wouldn't shift into O.D. until I took the rpm's up to 3000 then let off the throttle. No, I did not touch the brake prior to this.
Figure the tranny's gonna need a rebuild soon. What kind of upgraded parts does the wise and all knowing FTE wizards think I should be looking at? I tow the camper a lot during the summer so I want a trans that will hold up to the abuse. I'm probably stuck with this thing for a few more years.
View 14 Replies
CEL came on last night, OBD code PO420, truck is an 06 f250,5.4? Btw, truck running rough, no power on acceleration, in gear at idle, runs rough....
View 4 Replies
I have a 2007f550 auto trans with a flashing tow/haul light and a code of po791 coming up. Flashing light will clear in k/o position and remain off until placing selector in drive,after two feet or so of travel,an audible clunk and the trans acts like it is in third gear. Reverse is no change and highway will not shift into o.d. The iss "A" is listed as the culprit but ford doesn't list a iss a.
View 2 Replies
The truck is in my Sig 01 F250 5.4
Just got back from a long trip with it. Parked it for 3 days, all was running fine. Went to dinner Sat night and all was great, left the restaurant and as soon as I started the engine I noticed a slight vibration. As soon as I hit 42 miles per hour, it started shaking pretty good. I pulled over and checked under the truck to make sure I did not have anything I was not supposed to hanging down.
Driveshaft looked good, nothing leaking from rear end or tranny. When it does vibrate, the Tach shows the unhappiness as well. This a.m. driving to work it was vibrating at all speeds and shifting was very rough, had a hard time deciding if it wanted to be in second or third gear. I don't think this is drive train issue... When it shutters and sputters at 40ish MPH, its almost like it loses power and I have to let off the gas. and then under power it shakes badly.
I had the super chip settings for performance tow when this started and then I changed it back to stock settings, thinking it might work, which it only got worse. Changing the settings with the Superchip you have to disable the fuel system and I do this by pulling the fuel pump fuse under the hood in the power distro box.
I think the ujoints are still good, the oil and tranny fluid are spot on. Hubs are locked but in 2WD. Had all the front end replaced 15K miles ago. Brand new tires and wheels in Sept, front end alignment done at same time, front brakes were 90% and rear brakes at 20%.
View 10 Replies
I have a 2006 F250 with the 6.0 PowerStroke and automatic transmission. I just purchased this truck at an auction about a month ago.
Today I notice the transmission is not shifting into overdrive. No warning lights. If I press the tow/haul button in no change but the tow/haul light does come on. If I press it again (to turn it off) the tow/haul light goes out but still the transmission will not shift into overdrive.
This leaves me at about 2000 RPM at 68 MPH. I just had a Ford dealer perform Transmission service last week. (20,000 miles after the last recorded service.)
I am already not happy with the service I received at the dealer so I am really hesitant to take it back to them if it is something not related to the transmission service they performed.
View 5 Replies
My dad has a 2006 F-250 5.4 3v that spun a rod bearing at 107,383 miles. He's never been thrilled with the performance of it (told him he should have gotten the 6.0 when he bought the truck new, but why listen to a 15 yr old ). We've been throwing around a couple different ideas for engine swaps since the 5.4 is dead. We scored a 5.4 2V Lightning engine, but after trying to figure out transmission controllers or if we'd be able to tune the stock PCM for the 2v, we've put the project on hold.
Recently, I've been trying to convince him to do a diesel swap over the L-motor. I have a friend selling a cheap 99 7.3 with trans, PCM, harness, intercooler, piping and other misc stuff. Would that harness generally be plug and play with the body of the 06? Would it be more worthwhile to try to find a 6.0 from 05-07 and swap everything over?
I've also been considering a Cummins swap, although I haven't gone much past looking at complete engines on eBay and Craigslist. Would this be the better route, and just get a standalone controller for the 5R110?
So I'm looking for other's opinions. Should we go 7.3, 6.0 or Cummins? Should we stick with gas over diesel? Try to make the Lightning motor work? Or just go back with a stock 5.4 3V? I should say, he won't sell the truck for whatever reason, so he's not worried about resale or anything. We're in Michigan, so we don't have to worry about emissions. And we're fairly mechanically inclined, so I'm not too worried about doing the swaps, however my knowledge on diesels is limited.
View 4 Replies
2001 V10- F250.. Runs rough- had the computer put on it and was coming up with P0174 codes (I think that is right)- In any case I replaced the Mass air flow sensor- checked for any vacuum leaks visually- I did not see anything obvious.... still runs like crap.... smells like gas when idling.... anything else I can check??? The check engine light went off finally (probably due to the MAF)- but it's driving me nuts- Any hoses I have not located I need to check?
View 10 Replies
I have a 99 f250 5.4l 2v with 165000. just two weeks ago i went to start up the truck on a job site to take lunch and it was running really rough. I talked with a mechanic at my shop and he said that it sounded like the aic or that i needed plugs. I went and bought aic and plugs and installed them all in one day. I unhooked the battery before i did any work and have changed the coil packs about 3-4 months ago when it was jerking at highway speeds. I am at a loss.
Read so much on the site about could be this or that and cant afford to through money at it like the govt does. I replaced the ait(air intake temp sensor) and the ect(engine coolant sensor) after i got a code from oreillys that said p0113 which is high input on it. I have read it can be so many things and it seems to be running rich because i am getting about half of mileage i was getting before problem started. i need a fix soon as i must drive the truck to work everyday which is a 52 mile trip total.
View 14 Replies
I have an '06 F350 dually with a 6.0 diesel. I bought this used about 5 years ago and for the most part have loved it. i would always smile on the inside when i heard people bash the 6.0...i thought i got lucky....until today.
140k miles. recent oil change. all is swell...until this morning. Stick in key and turn it. glow plug indicator comes on...all lights come on for a few second....wrench, abs, dtc etc....wrench shuts off...glow plug light comes on...4 or 5 seconds later wrench light comes back on....turn key and NO CRANK.
All fuses are fine...starter cranks if i jump the solenoid...but it won't start. Miles to empty and everything else is just dashes hit the OBD and it says "engine sensor data error"/ "trans temp error" ...
View 1 Replies
2005 5.4l... Its giving me a code p0506 rpm to low idle air control system called for new one they said my truck don't have one said only up to 04 so what now truck idles rough n when u step on it it misses so bad its not funny feels like its laying over...
View 3 Replies
My truck has been doing this for a while now but it has progressively gotten worse from about three months ago when I went through some deep water. I don't believe it had to much to do with the water, I just think that the water is what didn't deal the situation and lead to the problem becoming more prevalent. But continuing, yesterday it got down into the high 20's and my engine started acting up (rumbling coughing, surging while at/leaving complete stops) and then it finally through a code for once and I head over to the neighborhood AutoZone expecting to get a lean code (because when the engine is acting up really badly I can unplug the fourth cylinder fuel injector without the engine acting any differently) but instead I received the p1152 (bank two lack of switching (rich)) code....
At this point I believe it is a faulty fuel pressure regulator, but without a good diagnostic obd2 reader or a fuel pressure gauge I'm not sure what to do. I'm currently in college, money is low, and I'm trying to take an accurate shot at the part that needs to be replaced so that I don't have to buy more than one part. Of course AutoZone says o2 sensor but I changed both about five months ago.. I've been chasing this diagnosis around for way too long now. (It's on a 2002 ford f250 5.4l super duty)
View 2 Replies
2006 F250 with the dash controlled 4x4. I typically keep the front hubs locked on this truck. I have recently noticed that when shifting into 4x4 that the a/c or heat will switch from blowing out of the vents to blowing out of the defrosters. Any clues how to fix this?
View 1 Replies
2006 F53 (motorhome) with 6.8L V10. Rcently noticed rough idle and midrange (under load) mis fire. Had codes on 2 coils. Replaced coils and put new spark plugs in. Did not improve and now detecting mild back fire.
Just completed compression test. 1=207psi, 2=200, 3=210, 4=190, 5=197, 6=200, 7=200, 8=170, 9=202, 10=208.
put some oil in #8 and retested at 225!
Other observations on #8. Engine has ticking noise chased with stethoscope to #8. THE new plug with 200miles, insulator going to electrode tip and everything inside combustion chamber is black. All 9 other plugs still look new out of box.
With the ticking noise I was suspecting valve but the compression test with oil jumped way up.
View 14 Replies
Have a 2006 F350 5.4l that is mainly used as a plow truck. I drive it at least once a week when not plowing just to make sure it runs ok, etc. Only put on about 2,500 miles per year. Keep it in good repair - not by me, but by the dealer or mechanics.
Problem - last two times I started it, it started ok but runs real rough for about ten seconds. Sounds like the engine is going to die. After about ten seconds, it "catches" and runs normal. Have no problems when driving it. If I restart it, it doesn't do this, so it seems to only happen when the engine is cold.
Battery was brand new back in Sept. All plugs were replaced maybe 3 years ago, as was the cat converter and muffler. Run non-ethanol fuel. What might be causing it before I bring it in.
View 6 Replies
2006 F53 (motorhome) with 6.8L V10. Rcently noticed rough idle and midrange (under load) mis fire. Had codes on 2 coils. Replaced coils and put new spark plugs in. Did not improve and now detecting mild back fire.
Just completed compression test. 1=207psi, 2=200, 3=210, 4=190, 5=197, 6=200, 7=200, 8=170, 9=202, 10=208.
put some oil in #8 and retested at 225!
Other observations on #8. Engine has ticking noise chased with stethoscope to #8. THE new plug with 200miles, insulator going to electrode tip and everything inside combustion chamber is black. All 9 other plugs still look new out of box.
With the ticking noise I was suspecting valve but the compression test with oil jumped way up.
View 8 Replies
What this means, how can I fix it? No technical jargon or abbreviations that I will not understand. The error code is for a 2006 F-250 6.0L Diesel automatic. I have a tow controller installed it came with the truck when it was new.
View 7 Replies
Ok just bought this truck ran fine. Put a sct tuner on that the truck came with and some how got the egr turned on. It had a egr delete so it was smoking and finally found it out that it had turned on but fixed it. Now we have another problem, it will start up and run fine and about 45 seconds it will start running rough and go into a limp mode. It will run rough and starts to die slowly and when it starts to die there is no throttle at all.
View 4 Replies
