Ford Super Duty (1999-2016) :: 2008 F350 4WD - Clicking Noise Only When Turning Hard Left
Dec 9, 2016
'08 F350 6.4l 4wd, I had the truck come in with a exploded transfer case. (See pics). Ive read all about this happening to many others. The truck still drove, hubs not locked, plenty of fluid in the TC, pretty sure it was the double Cardan that did it. Anyways I replaced thwith TC, replaced the front driveshaft, filled the TC with recommended fluid. Test drove and drives great, shifts fine. Only until I turned left.
At slow speeds turning hard or 15-20 taking a turn, it sounds like a ratchet clicking from somewhere on the left side, right around the drivers door, from what I can hear from the cab. Does it in 2wd, 4wd hi/low, hubs locked or not. I changed the vacuum pump, no leaks, changed the IWE solenoid, pulled out both locking mechanisms, tightened crossmember, checked everything from the hours of research I did on the internet. I cannot find the problem. I don't know what else to check. Front axles free spin and lock when they are supposed to. I'm at the end...
View 6 Replies
Advertisement
First off my trucks a 2000 v10 f250 with four-wheel drive and 2 wheel abs with about 230000 miles on it.
I Recently replaced my unit bearing on my drivers side because I thought it was the cause of a grinding that only happens on hard left turns but I wasnt the cause it was going bad causing play in the half shaft. I didnt seem to notice and wear on the shaft from bad needle bearings but I have to take it all apart again to be sure. Was just wondering what else could be the cause of this noise. I plan to pull the axel shaft and change all the seals.
View 3 Replies
I have an 03 F350 4x4 dually. Was pulling hard left at low speed when braking (front). Replaced pads, calipers, rotors, hoses and tires. Still the same problem. You can feel the abs activate right before it almost locks up the left front brake (basically will pull the steering wheel out of my hand). BTW the abs light does not come on.
View 2 Replies
Last couple drives I have noticed some front end noise on the left side. Back in May I also noticed grease all over behind the rotor. I believe this is the grease inserted via ABS hole into the unit bearing. I do not hear the needle bearing crunching while driving and did not here it in May either. I also attempted to move the unit-bearing up and down thinking the axle seal was toast but it seemed solid at the time.
Today I hear some noise while turning left which lead to the pictures below. Wet side is Driver side, dry side is passenger. Tomorrow morning I should have some time to take a look at this more in depth. Passenger needle bearing was changed last year and no issues since then......
View 14 Replies
An odd noise just started recently where as I'm turning left, a popping noise happens seemingly right under my feet. I don't have a video, but I can probably try to take one later. It sounds like something is loose and when the weight shifts off of the left side of the truck, something is shifting and groaning.
I lifted the truck up yesterday and there is no play in the ball joints, wheel bearings, sway bar/end links, or tie rod ends. There is no play in the shock or in the spring, nor is there any movement in the radius arm or where the axle mounts to the body.
I should probably add some info on the truck. '00 V10 CCSB 2wd. I can't see anything out of the ordinary, and can't reproduce the sound unless the truck is in motion.
View 9 Replies
My dually has started to make a rubbing or grinding noise just about every time I make a turn, left or right. What this could be, truck has 8500 miles on it.
SD Dually
View 9 Replies
I replaced both front bearings, calipers, brake pads, now I have a grinding noise on the left side front stops sometimes when you step on the brakes? 1999 F350 ...
View 6 Replies
Well, I tried this Death Wobble Kit on my Ford F350 Super Duty from a company called WC Motorsports. Had it installed at a Ford Dealership. DO NOT BUY this kit. Missing parts right out of the box. Also makes a horrible clanking noise after install. Piece of junk. Possible fix to one problem only to have multiple other problems:
1. Clanking Noise
2. Truck pulls to the left
3. Have to cut the factory subframe. (Never a good idea)
4. Changes the degree (not recommended by Ford)
View 10 Replies
I got a 2001 f350 got a noise in my left front wheel i know its not the wheel bearings, it only makes the noice when the locking hub is unlocked i did jack the the truck up and spun the wheel got a faint grinding noises form what seems like the locking hub so my question is bad locking hub or needle bearing holding the axle shaft??
View 3 Replies
2004 PSD 4x4 72k. I thought I would be proactive so I bought the front ball joints and have plans to install them but recently I starting hearing (and feeling) a clicking sound in the front LEFT when I make sharp turns to the left and hit small bumps now and again. I jacked up the front end and am able to get 1/4" of movement front to back (top to bottom so not steering) in the wheel.
I narrowed it down to the hub. I took it apart and it is most likely a sealed unit so no adjustment is possible....that I can see.I pulled out the locking hub and got as far as I can to know there is not an adjustment. Need to confirm that it indeed is a sealed bearing and if so what are the part number(s) I may need to repair it.
View 14 Replies
I have an '08 F250 w/ a 6.4. A couple days ago I started getting a loud squeaking when I turn to the right. It only does it under speed, almost like it needs the weight transfer to make the sound. In addition it's only when I turn at a like 45 deg angle, I can turn less or more to make it stop. But it has gotten louder and louder.
View 1 Replies
I recently switched back over to the 5.4 from a diesel. It's a 08 F350. I have about 38,000 on it now. I have no complaints so far, a little less power than the diesel, but I don't tow much anyways. The only thing I can't figure out is a strange noise at around 2500-3000 rpms shortly before a shift sometimes. The best way I can think to describe it is that it sounds like a turbo fart in a diesel. Almost like someone is putting their finger over an air hose on and off a couple times. It doesn't do it all the time, and doesn't shake the truck, or effect the shift at all from what I can tell.
I've put it through a lot of different shifts just to see if it might be transmission related. It downshifts and upshifts perfectly without any noise or slipping, and the fluid looks just as clean as brand new. No smell or anything either. It doesn't feel like torque converter shudder to me either as i can't actually feel anything in the truck, just the small noise. To me it almost sounds like it's coming from under the hood. I'm not overly worried about it right now, because it isn't effecting the way the truck drives or shifts at all, I'm just curious what it could be.
View 1 Replies
In forward drive or reverse, I hear a rotational noise that almost sounds like the bed creaking when you're getting it on. As I go faster the noise goes faster until drowned out by road and engine noise. The noise is unaffected by applying the brakes. I jacked the truck up and spun tires as fast as I could by hand and got no noise but when I lowered it back to ground and had the truck roll the noise was back. Noise is not affected by turning wheel.
View 13 Replies
Every time I apply brakes I hear a weird humming noise, as well as no stopping power. Checked fluids and pads and everything is where it should be. I heard abs can cause this but not sure on that. I know my master cylinder has a very small leak but it hasn't lost any fluids of that sort. I'm lost. I don't know where else to look.
View 2 Replies
I have a 2000 F-350,7.3, 6 speed. Just the other day I made a turn and my passenger got her feet wet. It had been raining and I also had the ac on. A couple of days later the same thing happened, but it had not rained, just the ac on. What is causing this. I do see condensate discharging under the truck.
View 7 Replies
I have a 1999 f250 sd with the 7.3. I'm not sure what is going on with my pickup. When I turn to the right i can turn with one finger, but when I turn left i have to put some muscle into it. Power steering fluid is full. I raised the front end and it turns both ways easy. My ball joints feel fine, there is no tire shake when i have it off the ground. My tie rods feel fine also, nice and tight. I was thinking about replacing the steering sector to see if thats the issue but wanted to get a second opinion first.
View 2 Replies
I'm having trouble finding the source of a vibration in the front end if my 1999 f350 super duty 4x4. The vibration is felt all the time but worse when under 40mph, while braking, and especially when turning.
I have replaced the rotors and brakes, tie rods and Drag links since the issue started but no change. In the vibration. What should I check next?
View 4 Replies
When in 4x4 and I go to do a 90 deg turn. The steering wheel pushes back to straight and seems like I have to fight it to turn the wheels. What could be causing this? I was in 4x4 Low on a dirt road at first then stopped, put it in Neutral, and turned it back to 4x4 High and then when turning in a parking lot it started doing this.
View 8 Replies
How to turn off the passenger airbag on my 2005 f350? Also any info about using Alex pepers OBD scanner on this vehicle? I have a three way interface but cannot get it to work.
View 6 Replies
Every time I connect the battery I get a clicking under the dash its non stop until I remove the battery cables. just when I remove the left passenger side battery. When I put in the key while its clicking and try to start its almost like I have no power the needle just drops down to nothing. The batteries have a full charge I pulled them off and charged over night also brought them in and had them tested. Seems like a serious short in the electrical but that clicking under the dash coming from fuse box scares me. I did pull all the relays and it still clicks.... doesn't sound good! 1999 F350...
View 5 Replies
Bottom-line question: is there a way to tell if a GEM is fried?
'99 F350 with a known water leak (not where it leaks, but for sure that it does--glove box, floor mats, etc.).
Recently started running the battery down, and then noticed that under low-voltage conditions it would click the door-lock relay back and forth, etc.
Now, after several inches more rain, it's making clicking and other electrical havoc noises any time it's not running, key in or out, even when the battery is up enough to start the truck (V10). I charged the truck and started it, drove it around to let it charge some more, and when I got home and shut it off, it was clicking as bad as ever.
After reading on the forums a while, I went ahead and pulled the fuse panel and GEM. The two big fuse panel connectors were definitely wet inside, and there's a little corrosion on one or two of the bayonet connectors. The GEM itself doesn't seem wet, and it doesn't look/smell like I've let the smoke out of it.
What do I do at this point? Last time, after I charged it up, it seemed to hold a charge and didn't do any clicking. I thought at the time it was related to the door switches that had been on the fritz (and which I lubricated after reading about where they are). Now, I suspect it was just because it had been long enough since it was rained on that things had dried out.
View 2 Replies
