Ford Super Duty (1999-2016) :: Passenger Seats Will Not Move Forward Or Backwards
Jan 12, 2016
Just bought my f250 and trying to diagnose the power seats. Both the drivers and passengers seats will not move forward or backwards. All other functions are working perfectly. The motor is not engaging in either direction. The tracks are not jammed. I'm thinking its a switch issue but what are the chances both have the same issue. Is there a way to test the switches? Looking for a wiring diagram showing pin outs of each wire and their function?
View 4 Replies
Advertisement
I have a 2005 F250 King Ranch 4X4 Diesel and now experiencing an issue with the front seat belts
The problem is while being worn sometimes they will not let you lean forward- they act like you have a foot on the brake pedal and are locked-you have to lean back and forth several times to get them to let out if reaching for something on the dash etc..
I have searched the forum and found many issues where the seat belts stopped retracting- but my issue seems to be unique in that the seat belt will at times 'Not Let Out" when you lean forward.
View 4 Replies
2003 F250 extended cab .. I've only had the truck a couple of weeks... While I was check out some lighting issues I noticed that the power door locks are operating backwards (unlock is locked and locked is unlocked) is the a simple explanation or has someone wired them reversed???? If you wired the driver's door backward would that effect the passenger door??
View 5 Replies
I am looking at a left over 2015 F250XL, 6.2L, 4X4, Short Bed. It is a new vehicle, 320 miles, it came in a dealer swap so that was the transfer miles. Truck was built in December 2014.
Question: It has bucket seats with no console. Well, there is some small plastic thing that is a cup holder between the seats, but NO arm rest center console. Is this normal? Or did someone take out the center console/arm rest and swap it into something else, and just found something to bolt to the floor? The one that is there appears it could be a factory piece, but man alive is it cheap.
Also, why no fold up arm rest attached to the seat??? Ford did this in the past. Is there a bolt hole to attach an arm rest from another Ford bucket? One that you could fold up and down maybe?? You would have to make a hole in the fabric to use it, but someone should be able to go feel around for a threaded hole or something.
View 5 Replies
I have a 2014 f 350 super cab xlt. Ford design engineers should be ashamed. But really who has installed the older (2009 ish) ford seat in there trucks for a little more comfort? How much fabrication was needed? Hate to say it but if I cant put the older truck seats in I'm going to buy GMC. These seats really suck.
View 3 Replies
There are 2 metal straps going left to right between the rear seat mounts. They don't appear to do anything. The seat doesn't touch them. The mounts are bolted to the floor so they don't give support. What they are for?
View 13 Replies
I'd like to replace the back bench seats with something that has a headrest. Can I swap out the benchseat from a 2004 model and place it in my 2003 model?
View 4 Replies
Just bought a 2011 F450 king Ranch. really like the truck but the heated seats a REALLY slow to warm up and then just warm. I see that these work different than all the other heated seats I have used and use the blower motor to blow warm or cool air through the seats instead of an element under the seat covers. Is there anything I can do to get more heat? The blower filters look ok and will replace the when I can find a set. Tries without the filter and didn't see much of an improvement. Where is the heat element and is it east to get to?
View 2 Replies
2012 f250 diesel Lariat 4dr 4x4. He called me today cause he knows I do all the work on my own F250 diesel. He has heated seats in the back and he said that they turn on by them selves and they won't turn off. He had to actually disconnect the wire harness to get the heating elements to turn off so his wife's friends wouldn't burn their bottoms in the middle of august is Texas.. Any ways, he said both sides are staying on and wouldn't turn off using the switch.
I'm not very familiar with the heated seat wiring, especially for the back seats. I told him their may have been a relay that went bad, but now I"m thinking that they much have a controller or something that is acting up. He said that the front seats are acting normal. Also, he has the touch screen and navigation upgrade as well as auto climate control, not sure if this stuff matters for the back seats though...
View 2 Replies
I have an 2002 F250 super duty that has leather seats. The seats are power but not heated. I bought seats out of a Harley Davidson edition that are electric and heated. They have an extra plug that my truck don't have. How can I make the seat heaters work?
View 4 Replies
I have a 99 v8 with a 8" lift. I just added a front leveling (mini spring pack) to replace the lifting block (death trap). Anyways after I installed the 2" spring pack and removed the 1.5" block the truck will not go into 4wd. Did I do something wrong? I did not unhook anything. I just unbolted the spring and shocks, lowered the axle down, then installed the new springs. By the way it has the warren aftermarket manual hubs (lock or free). I can hear the t-case engaging and the light says its in 4wd.
View 14 Replies
I have a 1999 F-250 4X4 7.3 lit Diesel engine. My problem is my transmission will go into reverse great no problem but it won't go forward. I have no problem rebuilding the transmission if that's what it needs, I just want to make sure there isn't a electrical issue from the PCM first?
View 14 Replies
Have 2001 F-250 7.3 PSD, automatic, ESOF (had to replace the original hubs with Warns)have kept up the maintenance,oil, grease, ATF fluid & filter, truck has been virtually trouble free. About 2 weeks ago I decided to go across an area of the lawn, as I was going (in 2 wheel drive)I felt the tires spin a little so I stopped got out and locked the hubs, got back in truck turned t-case to 4 high. had to rock the truck out of a damp area but nothing really.
So I got back to where I came in at (in reverse about 100') stopped put it back in 2 wheel drive, tried to go forward, very difficult, sluggish, got back in driveway had to back the truck in, will not go forward at all now. Checked all fuses, rapped the the t-case motor, no codes. So I thought I'd move the ruck, have a winch that will pull it out by the barn, I could not even move the truck forward by pulling it with a winch. As I said have never had any problems with truck. Transmission fluid is good, clean no burnt smell.
View 14 Replies
2003 F250 SC Lariat. 4x4, 6spd manual transmission, Manual hubs and manual 4wd shift. The truck shifts into 4wd perfectly. When I shift back into 2wd the transfer case stays in 4wd. If I back up it will go into 2wd.
View 7 Replies
It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problem, then when put it in Drive it revved like it was in neutral. There was no banging, no clunking, nothing to make it seem like something catastrophic happened.
I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more. Next I did the obvious and cheked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new.
I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? Ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check ***** were in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
Why this thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings? Can this be a "worn out" valve? or gasket issue?
View 1 Replies
2011 F250 6.7L Powerstroke, automatic tranny, Electric Locking Diff
When I engage the On the Fly 4WD switch the indicator panel says "shift to 4x4H in Progress" and everything seems fine but if I am not moving forward when I shift the 4WD doesn't engage. The engine revs up but nothing happens. When I release the accelerator the transfer case bangs like it is going to rip out of the truck. In reverse it is even worse. I am lucky that I didn't gun it or I could have done allot of potential damage. All my other Ford 4WD vehicles engage immediately from a full stopped position. This is quite of troublesome because if you have to shift when your stuck in the mud, your still stuck. If I shift while moving forward it works just fine.
My question is: Does this particular model (2011 F250 6.7L Powerstroke with an automatic tranny) have to be moving forward in order for the 4WD to engage?
View 3 Replies
I have a 1999 F-250 V10, I went to get into my truck to go to Lowes and only to learn I forgot my wallet. Here is where my problem lye. I came back home and decided to wait until the next morning to go back to Lowes, so I go to get in my truck cranked it up and went to put in reverse and it didn't move. It is like it is in neutral; so I went and put it in drive and still, it would not move. It is like it is in neutral. I can not figure out what is going on with my truck.
View 12 Replies
I have a problem. 2002 F-350 4R100 tranny. Put a reman transmission in about 30000kms ago. pulled excellent with no problems. shut it off for night. In the morning it had absolutly no forward and a little bit of slipping reverse for a few minutes now it is totally dead. No movement either way. The OD on off flashed a few times but not anymore. Put a Genisys scanner on and no codes at all. What could be the issue?
View 14 Replies
I have a 1999 ford f250 5.4 2 wheel drive i believe its a 4r100 transmission. auto. I have reverse but no forward gears. Ive heard this is a common problem , and on my reverse it has to hit 3000 rpm before it even tries to move and D 1 2 i have nothing only thing i hear is the engine sound changes gets deeper. Do i need a whole new transmission or is this fixable.
View 4 Replies
I can move the mirror adjuster switch and I can see the mirror trying to move and can hear clicking, but it won't move. It's like when the mirror has gone all the way in one direction and can't move anymore. But it does it in any position. I have hand-moved them to different positions and no matter where they are, the switch can't make 'em move into a different position. This happens with both mirrors. In case it matters, they are the power towing mirror that have the turn signal integrated on them and also they are heated.
View 5 Replies
02 F250 with 7.3. When I activate the 4WD, my light comes on, the A/C quits blowing out of the forward vents and goes into defrost and no 4WD. If I sit and wait a bit, the air again blows out the front vents and the 4WD engages. I figure I have a vacuum leak somewhere in the 4WD system. Is there a common place for this to happen or do I need to trace the whole system down? Also my manual hubs has never been turned and of course they won't. I know better than use a wrench so is there a easy way to free them up or just go ahead and disassemble and clean?
View 3 Replies
