Ford Transmission :: Extreme Grinding Noise In Neutral And Park
May 15, 2013
My Dad has a 01 f150 xtended cab 5.4 auto. Some of this info is second hand. He had driven it on a trip about 50 miles,when he started it to return he said it did not want to engage, put it in gear and nothing happened. Messed with it a bit and got it to go. was fine for about 30 miles or so. Then it started to make noise. I trailered it home and drove it a couple hundred yards to the shop. It sounds like a very large, very dry bearing, also seemed to catch/lock up then clunk.
With the wheels off the ground you can kick it into neutral and while the wheels are still rolling it quiets down. Also it does it sometimes while in neutral. When it is in park it sounds like stuff is still turning. At fist I thought wheel bearing or rear end until it made noise in neutral and park. The noise in park is not loud, just sounds like things are turning. It is full of fluid. The tranny has always worked flawlessly and still does even with the noise. Where to start looking? Transfer case?
View 1 Replies
Advertisement
I have a 1994 F-150 extended cab electronically activated 4x4, with the 302 V8 and an e4od transmission.
When the truck is running and it is in park or neutral it makes a grinding/whining noise and when it is in gear it doesn't engage, or occasionally will barely engage, but only enough to move it a little ways.
I've read a couple of post that suggested bad connections to the transmission could cause the transfer case to be in neutral which could cause a similar problem to this. I checked all the connection the best I could and the only thing I found that gave me any concern was one of the wires connected to the transfer case shift motor had some of the insulation melted or rubbed of and the wire was a bit corroded.
Is there any chance that this could be causing my overall problem with the truck not driving? Or what might be going on with it? Or any way I might be able to fix it without having to hand over a significant chunk of change for the full rebuild.
View 4 Replies
I have a 2008 Hyundai Santa Fe and there is a loud grinding sound when the car is in park and neutral. This noise doesn't happen all the time but i would say 50% of the time. When there is the noise it does go away when i put the car into drive or reverse.
View 16 Replies
I've got a 2001 E350 van with the 5.4 triton and 4R100 transmission in it. Has about 130,000 miles on it. I was doing some work under it a couple of days ago and noticed a rattling noise coming from the front of the bell housing. I can't hear it sitting in the vehicle or standing next to it but it's pretty scary sounding with my face under the inspection cover.
Shifting is smooth no noticeable problems there. Tranny fluid looks good, not burnt. After further investigation the noise is only present in park or neutral. In drive it goes away. In park it takes a few minutes of warm up for it to begin starting as a light tap tap, eventually working its way up to a clatter once warm. I know the 99 4r100 had some TC issues that sounded like this. It sounds like it's in front of the TC so I'm thinking the flex plate maybe?
View 3 Replies
I have a 2007 Elantra with 138,000 miles. I never had any slipping or jerking or reverse issues in the past. I got into the car put it in reverse just fine then put it in drive and nothing happened, I put it in park and the car kept rolling like in neutral and started making a loud grinding noise. When I put the transmission in any other gear the noise stops but will not move and acts as if in neutral.
View 2 Replies
My 2009 Sonata, 2. 4 L engine, base model with automatic transmission started up and ran OK, but 20 minutes later when I parked the car and shifted towards Park the gears grinded in neutral, stopped grinding in Reverse, and then grinded again when I made it to Park, and I quickly turned off the engine.
When I restarted, it grinded in Park, OK past Reverse, Grinded in Neutral, and then OK in Drive. How serious this is, or if there is anything I can check out on my own?
View 19 Replies
Looking for your collective expertise
2007 E350 with 5.4L and 4R70W trans. 107K miles and the fluid has probably never been changed ( my mistake - thought it was 100K interval - finding out from my reading that is def not true ). Anyway, following is recent development (last couple days):
Symptom #1: In Park/Neutral there is a whine. As soon as you put it in P or N, the whine 'spins up', stabilizes, and does increase with engine RPM.
Symptom #2: Hesitation (albeit minor) when starting from stop in D and R, with _very_ minor shudder. Sometimes feels like it's struggling a bit to move its own weight just until it's rolling.
Symptom #3: Shudder when accelerating in OD. No shudder when I turn off OD. It does not stop when applying brakes (a test suggested elsewhere). Also, the shudder does not happen when applying gas while braked in D at standstill. Only at highway speeds (enough to be in OD).
This all started at the end of a trip (90 miles or so in 85-90 degrees) when I was pulling a utility trailer (maybe 2000 lbs loaded). Not sure if related, but traction control warning went off a couple times. I think I have a axle seal leak that may be triggering that.
Otherwise shifts fine (no change in shift behavior or smoothness). Things seem to be worse when it has heated up. Should I start with a fluid change? Wasn't sure because there are comments out there saying don't do it or the tranny will just fail faster (I am skeptical).
View 3 Replies
I've got a 2006 F250 6.0 5R110W 4wd 220,000 miles It started getting a slight delay going into reverse and tow light flashing last week. all else functioning perfect Got a pending code P0700 and P0741 I stopped at NAPA when I was leaving no reverse checked every thing all was normal no leaks and fluid good color drove perfect in drive I got back to the shop [10 miles] put truck in park it was like its still in drive same with neutral, in reverse it wants to creep forward.
View 1 Replies
My 2011 Hatchback automatic has developed a whine in park, neutral and drive. ATF fluid level ok and changed by dealer every 25,000 miles. Seems to be coming from under the car. Could it be the transmission oil pump? If so, does it mean removing transmission to replace? I don't think it's the fuel pump. 62,000 miles.
View 5 Replies
I have a '94 E4OD trans in my '53 F100. It uses an analog MLPS for the gear selection indicator, Neutral Safety Switch, and Backup light.
My MLPS Neutral Safety Switch shows continuity in Neutral, but not in Park, I need to be able to energize the starter solenoid in both Park & Neutral.
Shouldn't the MLPS show continuity in both Park & Neutral?
View 5 Replies
Getting a loud rattling noise from the front of car in Park or Neutral? As soon as I put the car in D/M. I have heard that the transmission is noisy in neutral, but just want to double check.
View 8 Replies
My wipers lately park in the extreme "up" (all the way left) position. The only way to get them to park in the normal "down" position is to use an intermittent wiper setting, wait for the pause between strokes, and then turn it off. It's a 2002 model.
View 1 Replies
I was driving down the street and i noticed i couldnt get it in first gear, almost like a wall blocking it. and then i put it into 2nd gear and i started rolling... i turned my car off and when i started it back up, it had a slight grinding noise (in neutral). i put it in first gear, took out the clutch and i wasnt going anywhere... same with 2nd gear...
so i towed my car to the shop, they said my clutch went out and i "lost first and REVERSE gear".... is that possible?!
View 9 Replies
I swapped a t5 transmission from a s-10 into my 52 ford f3. I am trying to rundown a grinding noise coming from the transmission. I replaced the throw out bearing and the input shaft bearing on the transmission. With the transmission partially apart I couldn't find any obvious problems. The noise is only present when the clutch is depressed either in gear out out of gear.
Left in neutral there isn't any noise. I initially thought the throw out bearing was the culprit and replaced both that and the input shaft bearing. What could be wearing out? The transmission shifts perfectly but there is a binding noise when the clutch is released in first and sometimes second gear. another binding noise is present when making a hard left turn while starting out. I am at a loss here....
View 2 Replies
The problem I am having is that there is a grinding noise when in park. If i shift into gear then it is fine but shifting back to park very big grinding noise. At the same time I have the Speedometer and fan for the heat not working as well as the heater for the seats.
This problem is so bad I am afraid to drive and get stuck somewhere. I have checked the starter and it is tight ad secure. all fluids are fine. Not sure what this would be? This is the single vehicle i have for work and family.
View 1 Replies
When I start my vehicle, it makes a grinding noise, sounds like it's coming from the front of the vehicle, when I put into gear it stops. It started gradual and is getting worse. It's a 6 cylinder automatic, with 108 k miles.
View 3 Replies
I just recently picked up a 87 F250 with a 6.9 and a ZF5 trans. The PO replaced the clutch, and mentioned that he replaced the clutch fork too
Since I bought the truck, I've had some nasty rattling noises. It rattles when in neutral, and stops when I put the clutch in. The noise also comes back on occasion when decelerating at highway speeds, in 2nd as soon as I stop accelerating, and at low speeds in 3rd.
What is causing this?
View 4 Replies
I have a 4x4 5.2L 99 Durango. Everything was running great and the all of a sudden I started it to go to work one morning and it would not move. Now its making a grinding/whining noise when its not in park, it tries to move when I put it in gear but has the grinding/whining noise and is real sluggish. Then after its running for about 5 min it wont move or go in gear at all. I have had reg. transmission fluid changes and was running great. now this. Ive checked the fluid and its full to.
View 7 Replies
This noise started this week. Grinding when I take my foot off the brake when in park and parking brake set. What is causing it?
A guy at work said brakes. The front brake pads were replaced last year. Original rear.
Just over 90,000 miles.
View 3 Replies
I have a f1ta 5 speed trans on my 4.9 and when i press the clutch in and shift into 1st gear it makes a grinding noise then goes into gear after a little patience. but if i press the clutch and wait a few seconds, then shift into 1st its fine and goes right in.... maybe syncronizers not meshing or they're worn? or could it possibly be a low fluid prob? idk, it just started happening.
View 3 Replies
2001 Hyundai Elantra, with an automatic transmission.
1. I am experiencing a "grinding" sound upon my initial acceleration from park? This only occurs when the car has been sitting for a decent amount of time and the engine is relatively cold. To give you more detail: I start the car, throw it in gear and begin to accelerate. The grinding sounds is almost instant and sounds horrible. It is fairly consistent how long it lasts and generally once the car shifts to 2nd or 3rd it goes away. I do not hear it again until I park, leave the car for a while, then start it up and begin driving again.
2. I am hearing a "tension" like noise, also a little like scraping, when I brake at slow speeds coming from my driver side front wheel. I recently had my brakes replaced so I know its probably not the pads and at the time the rotors looked fine too. It is not a constant noise during the breaking either meaning, I apply the breaks, i hear it for a second, then it goes again, then it comes back, then goes away. Again it sounds like a mix between scrapping metal and tension.
What it could be, what I could look at on my own or how to get it resolved?
View 3 Replies
