I have a 2008 Hyundai Santa Fe and there is a loud grinding sound when the car is in park and neutral. This noise doesn't happen all the time but i would say 50% of the time. When there is the noise it does go away when i put the car into drive or reverse.
View 16 RepliesWhen I start my vehicle, it makes a grinding noise, sounds like it's coming from the front of the vehicle, when I put into gear it stops. It started gradual and is getting worse. It's a 6 cylinder automatic, with 108 k miles.
View 3 RepliesMy Dad has a 01 f150 xtended cab 5.4 auto. Some of this info is second hand. He had driven it on a trip about 50 miles,when he started it to return he said it did not want to engage, put it in gear and nothing happened. Messed with it a bit and got it to go. was fine for about 30 miles or so. Then it started to make noise. I trailered it home and drove it a couple hundred yards to the shop. It sounds like a very large, very dry bearing, also seemed to catch/lock up then clunk.
With the wheels off the ground you can kick it into neutral and while the wheels are still rolling it quiets down. Also it does it sometimes while in neutral. When it is in park it sounds like stuff is still turning. At fist I thought wheel bearing or rear end until it made noise in neutral and park. The noise in park is not loud, just sounds like things are turning. It is full of fluid. The tranny has always worked flawlessly and still does even with the noise. Where to start looking? Transfer case?
I have a 2008 Sante Fe with 165K mileage. At times, not regular, when restarting the car we hear a grinding noise. Immediately we turn the car off and re start, noise goes away. Could this be the starter going bad? Dealership wants 400 to fix.
View 27 RepliesI have a 1994 F-150 extended cab electronically activated 4x4, with the 302 V8 and an e4od transmission.
When the truck is running and it is in park or neutral it makes a grinding/whining noise and when it is in gear it doesn't engage, or occasionally will barely engage, but only enough to move it a little ways.
I've read a couple of post that suggested bad connections to the transmission could cause the transfer case to be in neutral which could cause a similar problem to this. I checked all the connection the best I could and the only thing I found that gave me any concern was one of the wires connected to the transfer case shift motor had some of the insulation melted or rubbed of and the wire was a bit corroded.
Is there any chance that this could be causing my overall problem with the truck not driving? Or what might be going on with it? Or any way I might be able to fix it without having to hand over a significant chunk of change for the full rebuild.
UK 2.2 Diesel
Problem for about 3 years. Always starts in neutral, rarely starts in park.
Any possible cause. Maybe a micro switch or a cable adjustment.
I have a 2007 Elantra with 138,000 miles. I never had any slipping or jerking or reverse issues in the past. I got into the car put it in reverse just fine then put it in drive and nothing happened, I put it in park and the car kept rolling like in neutral and started making a loud grinding noise. When I put the transmission in any other gear the noise stops but will not move and acts as if in neutral.
View 2 RepliesThe car has about 53k miles. The problem has persisted since probably 20k miles. The whine is only after the trans warms up and is in drive or reverse, not in neutral. Whine is while the car is stationary or moving at low speed. The whine doesn't seem to change due to gear it is in. It does not change frequency with engine RPM. It does seem to diminish the more load the transmission is under.
Whine is probably not an accurate description, it sounds like a noisy pressure relief valve. Had Hyundai service look at it and all they said was all pressures in the transmission are normal. They could not find any cause.
It sounds like a bunch of small ball bearings running in a loop and can hear each one impact. Sharp raspy impact type sound.
You cannot hear it from the interior but it is quite pronounced while in the garage or if you hear the car coming down the driveway.
My 2009 Sonata, 2. 4 L engine, base model with automatic transmission started up and ran OK, but 20 minutes later when I parked the car and shifted towards Park the gears grinded in neutral, stopped grinding in Reverse, and then grinded again when I made it to Park, and I quickly turned off the engine.
When I restarted, it grinded in Park, OK past Reverse, Grinded in Neutral, and then OK in Drive. How serious this is, or if there is anything I can check out on my own?
My 2001 Hyundai Santa Fe has recently started idling very high when put in park or neutral. While in drive the engine idles above 1K and you need to keep your foot on the brake to keep from moving forward. If you shut down the vehicle while idling high, the car will not start right away. It needs to cool down for 10 -15 minutes before restarting. It will run fine for awhile but will go back to revving up again.
View 7 RepliesI'm having trouble diagnosing a high RPM in park and neutral on my 2004 Santa FE 4WD 2.7L. Idle's great in drive and reverse. Occasionally when I start the car up it will shoot up to 3000 RPM until I shift into drive or reverse with a heavy thunk. Then it drives fine. When I shift back into park when I'm done driving, it will shoot back up. To avoid this, I just shut the car off in drive and then shift to park.The weird thing is, sometimes it doesn't happen at all. Sometimes it starts right up and shuts down with perfect idle. However, once I give it some throttle in park in these instances, the idle will jump back and forth between 1500 and 2000 and won't die back down to 800 where it should be until I shift into drive or reverse. Not sure what's going on.
I've replaced the idle air control valve, purge valve solenoid, and camshaft position sensor, but to no avail. I also replaced the throttle position sensor a few weeks ago, but that didn't seem to do anything, so I took it back. I'm wondering if I maybe didn't do the correct installation procedure. I still have the old grey TPS for what it's worth. Should I change this? I've also played with the tension in the throttle cable, but I don't really know how to get it exactly within specifications. I definitely removed some slack. I just checked for vacuum leaks using the cigar method with a hose from the PCV valve with the throttle body sealed with saran wrap, but I couldn't find anything. My method was shoddy, and I don't really know what I'm doing, so I wouldn't rule out a vacuum leak by any means.
On my 2012 Santa Fe I'm getting a whining noise from the engine while it is park. I think it might be alternator.
View 3 RepliesI have a 2010 Santa fe ( since new) 28k miles - I'm getting a grinding noise that seems to come from the front right wheel - noticeable only when doing a right hand turn or going around a roundabout.
So, Is this likely (from my terrible description) to be a wheel bearing problem....
2010 SF Limited, about 46,000 KM.
Heard a grinding noise coming from the back of the truck today. First thing I thought to look at was the rotors. They looked warped/wavy and were really hot. I'm worried that the pads are used up and its metal on metal, really looks like rotor damage. I'm confused by this...
1) I get a safety inspection done every time i'm in for service (6km), no service rep has ever warned me about my pads.
2) Aren't squealers supposed to warn the driver of low pads?
3) Pads wear out faster in the front than they do in the back. How could the back pads be used up already? The front looks fine.
So if my back calipers are seized, or the e-brake line froze, then i'm driving with the back brakes engaged full time. This should not have happened to a truck so young. Do I have a warranty case here?
I have a 2007 SF Ltd. About 6 months ago I noticed a tiny grinding noise coming from the front end. I took it to the place that installed the brakes and rotors and had them look at it. The said that they didn't see anything but the cleaned up the rotors and oiled the slide pins. That didn't seem to sold the problem, so I took it to the shop that does all my inspections and such. They mentioned that they didn't see anything and that if if was only first thing in the morning, it might be some very minor rust that is building and being worn off. Lately, the grinding noise has gotten much more consistent and loud. Both places said the pads looked almost new and other than the turning of the rotors, they looked fine. If it isn't the pads or the rotors, what could be causing the grinding noise? A friend of mine had the same issue but his dealer told him that his vehicle "just had noisy brakes". That doesn't see to be an acceptable answer.
View 3 RepliesMy 2007 Santa Fe Limited 3.3L with 102,000 miles started making a grinding/ticking noise yesterday. It's hard to tell but it sounds like its coming from directly under the center console. The noise is directly proportional to the speed and if I put my hand on the shift selector, I can feel the tick vibrations. It drives and shifts fine. What it could be? I'm hoping it's not a transmission issue. I'm thinking something with the AWD connection to the rear wheels.
View 1 RepliesMy automatic 2007 Nissan Altima has developed an intermittent problem when I go to shift it into park it won't shift down past neutral. I can't physically move the gear shift past neutral and can't take my key out of the car. If I wait awhile or drive off somewhere else it will later allow me to shift normally again and won't happen for awhile. It has happened maybe 8-9 times but I worry it will get worse or break the transmission. I've taken it to a mechanic and they looked at the transmission and didn't see a problem but sense they couldn't recreate the issue they couldn't fix it.
View 1 RepliesLoud engine grinding noise accelerating from stop when you first start the car? It is right after cold start, lasts 10-15 seconds until I get to 30-40mph. Engine sounds normal otherwise.
2008 LS600hl with 28K miles
Looking for your collective expertise
2007 E350 with 5.4L and 4R70W trans. 107K miles and the fluid has probably never been changed ( my mistake - thought it was 100K interval - finding out from my reading that is def not true ). Anyway, following is recent development (last couple days):
Symptom #1: In Park/Neutral there is a whine. As soon as you put it in P or N, the whine 'spins up', stabilizes, and does increase with engine RPM.
Symptom #2: Hesitation (albeit minor) when starting from stop in D and R, with _very_ minor shudder. Sometimes feels like it's struggling a bit to move its own weight just until it's rolling.
Symptom #3: Shudder when accelerating in OD. No shudder when I turn off OD. It does not stop when applying brakes (a test suggested elsewhere). Also, the shudder does not happen when applying gas while braked in D at standstill. Only at highway speeds (enough to be in OD).
This all started at the end of a trip (90 miles or so in 85-90 degrees) when I was pulling a utility trailer (maybe 2000 lbs loaded). Not sure if related, but traction control warning went off a couple times. I think I have a axle seal leak that may be triggering that.
Otherwise shifts fine (no change in shift behavior or smoothness). Things seem to be worse when it has heated up. Should I start with a fluid change? Wasn't sure because there are comments out there saying don't do it or the tranny will just fail faster (I am skeptical).
Getting a loud rattling noise from the front of car in Park or Neutral? As soon as I put the car in D/M. I have heard that the transmission is noisy in neutral, but just want to double check.
View 8 RepliesI've got a 2001 E350 van with the 5.4 triton and 4R100 transmission in it. Has about 130,000 miles on it. I was doing some work under it a couple of days ago and noticed a rattling noise coming from the front of the bell housing. I can't hear it sitting in the vehicle or standing next to it but it's pretty scary sounding with my face under the inspection cover.
Shifting is smooth no noticeable problems there. Tranny fluid looks good, not burnt. After further investigation the noise is only present in park or neutral. In drive it goes away. In park it takes a few minutes of warm up for it to begin starting as a light tap tap, eventually working its way up to a clatter once warm. I know the 99 4r100 had some TC issues that sounded like this. It sounds like it's in front of the TC so I'm thinking the flex plate maybe?