Recently bought a 1999.5 vr6 jetta and noticed that it will randomly grind going from 1st to 2nd gear (its a manual). It seems really erratic, it will do it at any rpms and at completely random times.
It only does it when shifting up, not downshifting. I can also go 50 times or more shifting into 2nd without it happening or it can happen 5 times in a row. Not sure what do here...
I noticed through careful investigation that my 03 GTI 1.8T (180,000 KM's or 111,850 miles) will grind 3rd when in these conditions:
1. When the car has been driving for more then half an hour and everything is hot
2. When the car is over 2800 RPM's while hot (ie. getting on a highway)
Now I know lot's of people blame syncro's and yes I could see that my car has had 8 previous owners so I can't say they all shifted perfect. But what I do know is that when I downshift from either 4th or Neutral it will never grind even when I don't Rev Match or "Blip" the throttle. So it can't be syncro's in my opinion.
So what I've done to the car to rule out some problems were:
- Change the gear oil from what ever it was before to Royal Purple 75W-90 (NO luck.)
- Then I added a short shifter and adjusted my cables properly (still No luck)
- Finally I noticed my shifter was sloppy and one of my bushings were torn so I bought 42 DD's metal bushings and the shifter did stiffen up a lot, however!!! (No luck)
I know it's not my driving technique because I watch my foot depress the clutch fully and then I gently push it into third. I also know I'm shifting correctly because I can double clutch and normally shift through every other gear properly without any grinds or clunks. Just the devilish 3rd gear.
I would like to hear the solution. I'm going to change the oil one more time to Redline MT-90 and see how that goes, but if that doesn't work I might just tear apart or get a new tranny.
I just bought a 2012 R last friday. 14k on the odometer.
Car is perfect, cept when i shift into 6th its really grabby with a grind. does it every time.
should I take the car in to have it checked out, is this normal?
I have a 2003 Jetta Gli , 24v vr6 with a 6 speed transmission.
Well this all started last night, started to drive, when accelerating , around 3k RPM I start to hear a rattle or grind. This only happens around 3k while accelerating. Once letting off the gas or pushing the clutch in, it goes away. Sometimes after 3k it'll go away.
I've been having 2000 Jetta GLS VR6. It has an automatic transmission and lately I've noticed that when I put it into Drive, it starts out in 3rd gear. In other words I've lost 1st and 2nd gear when put in Drive. When I manually put it in 1st gear with the shifter, I have 1st gear and all the way up to Drive. The issue just seems to be while in Drive (D)
I've tried the Automatic Transmission Reset :
[URL]...................
Perhaps I'm not doing it right as I can't seem to see any switch under the Gas pedal, just a round piece of plastic that protrudes an inch. I've even removed that and still see no switch.
I come today for a apparently transmission problem. I have an automatic VW Jetta 2000 2.0 that i bought a few months ago, the car is great, has 250K miles.
The problem is in the morning when car is still cold, the transmission isn't shifting gear until 3K RPM (For 1-2 is about 2.5K RPM, and 2-3 is about 3K RPM). After 5 minutes of driving all back to normality and transmission shift gear about 2.2K to 2.3K RPM.
The question is: this is normal?, what could be wrong?.
So, I recently picked up mt 2000 vr6 has 200k on it runs great well taken care of. I was just driving not getting crazy or any sort of thing. it has ground in 2nd a little from when I got it. I put it in neutral then went to put it in 2nd and it went but nothing there. it will go into 2nd but won't stay and when I hold it in 2nd gear it just revs no noise or anything just sits and rolls. tried doing the reading but all I fold was 1st and 2nd I just have no 2nd.
View 1 RepliesI have a 2000 Jetta with the 2.0 automatic and just like the title states, I have recently developed a engine vibration that is felt at all times. It is much worse when the car is in gear. I only seem to feel it in the gas and brake pedals. It does not seem to depend on speed nor does it only occur at certain rpms. It feels like someone zip tied a vibrating back messager to my pedals. I want to find out what it is because on long commutes my foot begins to feel like its falling asleep. I can visually see the engine vibrating with the car in gear. I am leaning towards motor mounts.
View 1 RepliesI have 1 month left on my AAMCO rebuilt transmission. I took it in a few weeks ago when it went into "limp mode" (Stuck in 1st gear). Eventually, they got an error code of P0730, which I believe is electrical-related. All was pretty good but then today, driving @ high speed on the interstate, I could not get into 4th gear...
View 1 RepliesJust within the last 1000 miles my MINI has been randomly grinding into second gear (6 Speed Getrag Manual for the Cooper S) when turning right. It is a little notchy when traveling straight and beautifully smooth when turning left. When pulling out of my garage the other morning I went into second but purposely pulled the gear stick towards the right side of the gate and it did the same grinding thing that it does when going around right hand turns. It seems as though something is out of alignment? It feels like the shift linkage is not properly placing the internals of the transmission. It happens mostly when cold and once warm the random harsh grinding stops and it goes to simply really notchy.
View 12 RepliesOk, I'm finally ready to dump out this stock tranny fluid and put in something else to alleviate the 3rd gear grind. Question is, which one should I put in?
View 18 RepliesI have a 1986 Ford Bronco straight six 300 4 speed manual NP 435
She grinded a bit when shifting from a stand still but nothing terrible for an old rig but leaked oil bad from the rear main seal so I took out the tranny/t case to put in new clutch, throw out bearing, pilot bearing, and rear main seal. When I put it all back together shifting into 1st would grind like CRAZY. So would reverse but not near as bad. So I took it all back apart inspected everything even torqued the clutch to specification. Put it back together and same result. So I replaced the slave/master cylinder thinking the clutch wasn't pushing enough bench bled it and still no luck.
Background facts:
Tranny swapped from my 4 speed auto to a 1.8t o2j 5spd
13lb. Light flywheel
Powerflex dogbone mounts
Peloquin LSD
The problem: Very hard to get a smooth shift from gear to gear. Trust me, I know how to drive, but I can always feel the car shifting into a different gear if you know what I'm saying. On my friend's bone stock Jetta, I just let the clutch out without gas in between shifts and you don't feel a thing.
On my car, you feel EVERYTHING. People have told me the light flywheel will make the ride more uncomfortable in many ways, especially since the RPMs drop much quicker in between shifts than stock.
I just got my 03 F-150 with 112k on the clock. It has the manual 5 speed tranny behind the 4.6L.
However, since I've gotten the truck, it's kind of difficult to put in first gear. If you are sitting at a light and in neutral and the light changes and you push the clutch to the floor and put it in 1st (fairly quickly - a normal reaction time), it will actually do a little grind and/or thump. However, if push the clutch to the floor and wait a couple of seconds and then shift into first, it's a bit of a "push" but it will go in without grinding.
Once in a while shifting to 3rd it feels the same way, but won't really grind.
I'm just wondering if that means the clutch is toast or is it the trans that is toast? Reason I ask is my 96 Cobra with the T-45 5 speed would grind going into 5th gear if I just normally put it in. I used to have to put it in neutral and then push the clutch in again and slowly shift to 5th for it not to grind. And it wouldn't go into 3rd if I tried to shift fast or under power. I replaced the clutch and found out the trans was actually going bad, but it had 173k on the clock.
So, I'm really paranoid that it's my darn trans in the truck instead of just the clutch. Whenever my old Camaro clutches used to be dying, they would slip more than they would ever grind going into a gear.
Last night, on my way home, I suffered a catastrophic transmission failure in my 1991 2.3L 5 speed. Stepped on the clutch on an exit ramp from the freeway and was rewarded by a LOUD screech/grind, a stopped vehicle, and a transmission "locked" in 5th gear. The local HERO service pushed me out of traffic and I got towed home. Looks like a transmission transplant is in my immediate future. So - the question is, what year manual transmissions match up to a 1991 2.3L 4 cylinder, standard cab, 2WD? I need to start searching salvage yards.
View 3 RepliesWell here it is I just put a new slave cylinder in my 02' F-150 and once we figured out all the little issues we were having we finally got the truck to fire up!!! Now my problem is that when the truck is running I can't get the truck into gear with the clutch pushed and it doesn't even grind. But when the truck is off it goes through the gears no problem what so ever. When we did the slave cylinder while we were in there we just replaced everything clutch, pressure plate, flywheel, rear seal, and pilot bearing. We figured that since all the shops were quoting me 800 and up for just doing the slave that since were in there we might as well do everything since nothing has ever been replaced yet. My question is why will the truck not let me shift into gears when running but no problem when off. Oh and yes the system was bled after doing the slave actually twice so far.
View 5 Replies148,000 miles, and yesterday my R decided it would no longer allow me to use first gear. It sort of starts to go in gear, but feels kind of mushy, not positive, and if I let out the clutch, the gears grind, but will not engage. All other gears feel and perform normally.
View 7 RepliesI'm most likely picking up a 03 jetta glx vr6. Thing is the 6th gear is out. Is the entire transmission about to break or is it a common thing?
View 16 RepliesLLast night I was driving. I got off the highway and pulling on to the main road in 2nd, I ripped on it and went into 3rd quickly. It basically kicked it out of gear, and didn't seem like I had any other gear besides 1st or 2nd. Got to a local gas station in 2nd, and I originally thought my linkage had come off. While trying to back into a spot to make life easier, there was no reverse. seems like the trans is binding up. Aligned the linkage anyway, when the car is off, it goes into every gear, but when it is on, it feels like 1st-2nd-nothing. If I roll the car backwards and then forward, I have 1st. Other than that, it will not engage. If I put the trans in reverse and then try to back up, it feels like the trans is binding. Same with 1st, unless the car is running. Traction control light will not turn off either, will have it scanned this week to determine that issue...
Ive seen most people have issues with the 1st-2nd shift fork and have this causing the reverse issues.
2005 GLI 1.8t
The car was starting to have issues going into gear after a night of cruising. Then I was experiencing what I am thinking was clutch creep. The clutch would be down and in gear and the car wanted to slowly roll.
What I have done to try and fix it:
I have bled the system many times to get all the air out(i believe), and also readjusted the the linkage. NOW, the car will not go into gear when it is on but will when it is off. I have the car on stands at the moment and it will shift through all the gears when the car is on just the wheels spin since it is in the air.
The clutch/flywheel/pp/throw out bearing all have less then 2k miles on them. Tranny fluid has been replaced with Penzoil syncomesh. I have yet to ever do a hard launch.
Clutchmasters Fx400, OEM DMFW.
Car is an 02m trans w/o the black cap in the side so I cannot do the washer/gasket mod for clutch creep. Believe I have to order NLS shim kit and put behind the throw out bearing.
So I drove 400 miles today and when I was just about home I heard a grind when I applied the brakes on the freeway. Well I did a walk around the car to check all the pads and noticed my rear pads are almost gone. I'm not used to having the rear brakes implemented in so much of my daily driving, with the TCS and all.
To make it easy I'd like to keep all four corners on the same brake setup, I'm just not sure what is ideal on this car. I know OEM is gonna be said, but I upgraded my front pads to Hawk HPS'.