Golf IV / Jetta IV :: How To Replace Vehicle Speed Sensor (VSS)
Sep 10, 2011
2002 Jetta 2.0L...
The Haynes Manual tells you to lift the car up and un-mount the engine mount on the drivers side of the transaxil to get access to the VSS underneath the vehicle, but you can do it from the top of the engine!
1. Take out your Air filter box for easier access
2. My VSS was covered by a metallic heat pouch with snaps. (not mentioned in Haynes Manual)
3. I got Needle nose pliers to wedge in the small area to unscrew the bottom half of the VSS. It is a small area to get your hand in, but with the needle pliers was actually pretty easy.
4. Then get something small enough to release the clip for the top plug. I used my screwdriver.
5. Screw in your new VSS and plug the top cable back, then put your air filter back in place.
If you look at the pictures I took, you can see the VSS and the silver pouch I mentioned. I had a lot of trouble finding the location of the VSS with no real good pictures or explanations online. Note these pictures were taken from the drivers side, which the empty space is where the air filter was and on the right you can see the battery.
View 18 Replies
Advertisement
I just recently purchased my first mk4 golf 2.0 after having a mk3 jetta vr6 for two years. I've been having problems with the car shifting (automatic) i put a code reader on it and came up with p0722 output speed sensor which explains why it sometimes shifts at 4500. My two questions are where is the output speed sensor located? and what is a normal shifting range for properly running automatics?
View 2 Replies
Recently, my I4 XLE camry with abs came up with a cel P0500 - Vehicle Speed Sensor A Malfunction. Where the vehicle speed sensor is located? i doubt this thing's hard to service, but so far i have no luck finding it.
View 13 Replies
So I am getting a CEL and p0501 (Vehicle Speed Sensor) code and don't quite know how to approach it.
Other forums/posts suggest that I check or replace the input and ouput sensors on the transmission, but from what I understand those are each a unique code, and the p0501 is for a sensor located on the transaxle. Is this the case?
I was under the impression that because my car did not have ABS that I did not have the latter sensor on the transaxle, only the input/output on the transmission. If that is the case, will replacing both eliminate the CEL/p0501?
View 1 Replies
Where the vehicle speed sensor is located on the 2007 es350. Reomoved battery and air filter box but just can't find it.
View 1 Replies
My car is now 24/7 with this error which is Vehicle Speed Sensor malfunction an there seems to be no way of solving it, symptoms are:
*Speedometer not working, needle always in 0
*Power steering not working
*Car wont past 3rd gear
*Check engine light and power steering light on
I checked all 4 speed sensors and the wiring looks good and they look good. Also if i hit a bump, issue goes away for a couple of minutes, until i hit another, etc, so looks like a wire or short circuit, cant tell. Is there a speed sensor on the transmission as well? where is located?
View 1 Replies
I took the car out for a little spin about 8 miles. We where about .5 of a mile from the house and there is a section where you have to stop on a little bit of a hill. I stalled the car due to the new Dm clutch then headed to the house and the car started to run like crap. I hooked up VAGCOM and had this code:
17748.P1340 camshaft position sensor-G40/ Engine speed sensor-G28: incorrect allocation(#1)
I swapped out the 2 cam position sensors and cleared the code and started the car and it still ran like crap. I just happen to have a new Cam position sensor(hall sensor) so I swapped it out in both cam positions one at a time and cleared the code and the car still runs like crap.
Is there a way to check(test) with vagcom to see if its one of the engine speed sensors?
View 24 Replies
1 Fault Found:
00323 - Vehicle Inclination Sensor (G384)
008 - Implausible Signal - Intermittent
Freeze Frame:
Fault Status: 00101000
Fault Priority: 4
Fault Frequency: 3
Reset counter: 143
Mileage: 133853 km
Time Indication: 0
Date: 2000.00.00
Time: 17:27:31
View 5 Replies
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 Replies
is locking in 4m but is too high, suppose to be ~2200rpm.When I checked with vagcom the speed shown on computer show a speed with 20km/h higher than the real speed (shown at speedometer)
View 14 Replies
Ive got a 2001 MKIV Golf GTI. Recently I've had some clutch problems, I kept returning to the car and finding the clutch on the floor. After a tow My mechanic managed to get it back after a lot of pumping and messing around, and told me It needed a Slave Cylinder. So that night after driving home (clutch wasn't feeling good) I came out and found the clutch on the floor again.
So I went out - got a new genuine slave cylinder and replaced it myself. But now I cant for the life of me bleed the clutch - I've bled brakes plenty of times but never a clutch. I am doing it manually, I've read online some guides.
1) Crack the bleeder & push pedal down... because its got that spring, it stays on the floor.
2) Close the bleeder, pull clutch up with hand...
Ive been doing this over and over and over, but nothing happens... fluid isn't even coming out of the bleeder. Im guessing this could be because the slave has no fluid in it and there is an Airlock?? I want to try to avoid getting another tow truck.
View 2 Replies
I need to replace the fuel line that connects to the fuel rail, it is old and corroding and drips out gas when I dry so I need to replace it. I have the new fuel line for it but how would I go about taking it off and the clamps? Just wanna make sure I am doing it right.
View 1 Replies
After getting some misfire and hesitation (code reading says misfire on cylinder 3), it looks like I'll be doing my first spark plug change on my 24V VR6. I've ordered all of the plugs, and have made sure that I'v got all my tools on hand. Hopefully, the DIY's I've found on Vortex will be as useful as they look .
My car has 163K on the clock, and spark plug change has been on my short list of to-do items, as I'm not sure of the maintenance history of the car. Hopefully, the spark plugs will do the trick, but coil packs will be done soon too.
Would it be OK to change just the coilpack on cylinder 3 and leave the others alone if they are all working OK? Or just shell out the cash to change all six at once?
View 2 Replies
Headlight bulbs. So I am looking to replace my bulbs because mine don't seem to have that great of light output. I am not sure if it is the actual headlight or if it is just the bulbs? Is it possible to just replace the bulbs and get better light output? I am not sure of the brand of headlights I have but I am pretty sure they are some cheap aftermarket ebay headlights. I want to replace the headlights in the future but for now I was wondering if I can get away with just replacing the bulbs. When selecting the bulbs, are they all pretty much universal or do I have to buy specifically for the type of headlights I have?
View 10 Replies
I have a 2002 Jetta TDI with the grey leather parking brake handle cover and would like to replace it. How to do this and if I will have to remove the armrest & the plastic trim around the handle?
View 2 Replies
I've lost all power steering about a week ago. I checked all the lines the return is bring fluid up from the pump and the res is flowing into the pump.
A) should I replace pump?
B) look into other things that could be causing the issue?
View 9 Replies
Basically I want to replace all my boost/vac lines with silicone. I have a 01 jetta 1.8t with aww engine code. I need to know the diameter and length of each.
View 1 Replies
I just purchased a Jetta and it needs both side mirrors replace. Now I have used the search with a lot of success but for some reason I haven't been able to find out how to get to the bolts for the side mirrors. How do you get to the bolts to replace the side mirrors ?. I am also sure I could figure it out in time but I would rather not break anything trying to force parts off.
View 2 Replies
The following occurs: When car is in PARK there is no strange vibration even with AC on.
When DRIVE is engaged, vibration begins, even worse with AC on. Once the car accelerates vibration is gone.
I went to the authorized dealer service shop and they told me that this symptom is typical of these cars, they even sat me in some other cars to prove that these vibrations are normal.....
View 8 Replies
I am replacing my front passenger side door on my 2000 Jetta GLX. I have been searching online for detailed instructions on how to do this, but have turned up empty handed.
View 1 Replies
While braking, the car is revving up to about 1500 rpm and causing the vehicle to shudder and buck as if it wants to take off with no throttle input. The car is an automatic and this is the information relayed to me via my sister.
The car is a 2002 Jetta 2.0 automatic wagon.
View 4 Replies
