Grand AM :: 1994 / 2.3 Quad OHC Stalls In Reverse
Sep 2, 2007
I have a 94 grand am 2.3 quad ohc 8th number in vin is 5 the car run fine in any gear except reverse. Soon as its put in reverse the car stalls right out.
View 3 Replies
Sep 2, 2007
Advertisement
Grand AM :: 1994 2.3 L - No Power On Acceleration On Highway
I have a 1994 Pontiac Grand Am 2.3 L. I went 3 blocks yesterday to the highway and as i got ready to pull out onto the highway I lost power (like foot feed to the floor and going 20 mph). Drove it back home (3 blocks) and the engine is over heating within 3 blocks but temp gage isn't registering over heating (Incredibly hot under the car within 3 blocks). Engine was shaking badly and whatever it was blew a hole in my muffler? Put on all new spark plugs, oil change, oil filter... No more shaking in the motor but still no power when trying to go. Cut catalytic converter off and tried to drive out of the driveway, still no power on acceleration.
View 5 RepliesCherokee :: 1994 Grand Laredo / Error Message - Service 4WD Switch
What is the solution to the "Service 4WD Switch" error message. My 1994 Grand Cherokee Laredo(4WD ALL-Time) keeps displaying this message every 2 minutes and it's so distracting. My mechanic doesn't seem to have a clue.
View 14 RepliesGrand AM :: 1996 - Theft System Light Comes On And Then Car Stalls After Startup
When you start the car the theft system light comes on and then the car stalls. This has been a continuous problem for about two years. I can't find any pattern to when it does and does not start. Sometimes it will start again the next try, sometimes 30 minutes, sometimes I have it towed to the pontiac dealer after a week of not starting. Recently I have had the cluster sent out twice to check for problems, a new lock cylinder, and the bmc replaced. (about $1,150 total) This was done by a certified pontiac garage and the problem is still not fixed so I dropped it off again last night. Any suggestions? Also is there a point where I should get reimbursed for having parts replaced that were not broken? I have to believe that if the problem is still happening then there was nothing wrong with the lock cylinder or the bcm.
View 14 RepliesGrand Prix :: 2002 Starts But Stalls After PW Switch Replacement
My son had the car and put the window down and it would not go back up. Had to drive 13 miles in below zero temperatures to get home. After searching online and doing some checking on the vehicle we found that the Driver's PW switch was dead. Went and got a used switch and replaced it and the window works find. SO, the husband goes to start it and the battery is dead so he put a charger on it and it did start but it stalls right away. It will stay running if you have your foot on the gas but as soon as you let off it stalls. If it idles at all before it dies it it does so erratically.
View 10 RepliesGrand AM :: 2000 V6 SE - Rough Idle And Stalls / Gears Not Shifting When Car In Motion
My grand am has a gnarly idle issue. It stalls to turn on and once on it has a very rough idle. When I put the car into drive it stales then just turns off. Drained the heck out of my battery so I was thinking it was an alternator issue but I did a quick test and my alternator seems to be working fine. I did manage to drive my car but once in motion, gears wouldn't shift which has me leading to thinking it can be a transmission issue.
Specs:
2000 grand am
3.4L V6 SE model
automatic
Cherokee :: 1996 Jeep Grand 4L Stalls At Idle And At Highway Speed
1996 Jeep Grand Cherokee 4L
Problem "Stalls at idle and at hwy speed" sometimes starts right up and sometime will not start. Sometimes it will lose acceleration but engine will still be running and you can punch the gas and it will go again.
It has been in the shop for most of the last 2 months. Driven in 3 times and hauled in twice.
Low mileage 70,000 - has been great until now - serviced regularly.
Did get new fuel pump only about 10,000 miles ago do to starting problem but in that case it just did not start.
Independent shop replaced distributor cap, rotor, coil, fuel filter. No codes and couldn't duplicate problem.
Jeep dealer replaced fuel pump (they said wiring problem), O2 sensor, engine module no help, they asked us to pick up car because it ran fine. It stalled within 2 miles of shop.
We replaced gas cap just in case.
Limped back to shop to replace crank sensor as it was suggested several places. Ran fine for about 45 minutes then back to old tricks. Relays have been checked. Still at shop trying to trace problem. At least nobody is saying they can't duplicate problem as it now stalls all the time.
Grand Prix :: 2000 GTP Only Moves When Put In Reverse
I have a 2000 GP GTP. I went over a speed bump to fast one day, and parked my car. When I got back into the car the next morning, I tried to put my car into drive and it wouldn't accelerate or move. So I put it into lower gear, 1st to be specific, and the car moved normally. I drove like that for a few days with no problem. Then days later I did the same thing, went over a speed bump to fast and now the vehicle wont move at all unless I put it in reverse.
View 2 RepliesRam / SRT10 :: 98 1500 4x4 Quad Won't Start Just Clicks Once
98 1500 4x4 quad, 5.2.. Did run fine. Go out to start wont start just clicks once. Replaced starter and the battery. Still only clicks once. checked voltage across terminals to the grounds. swapped relays around still one click. Going to check in the morning make sure it didn't seize.
View 4 RepliesPontiac - Grandam :: 1997 GT 2.4L Quad 4 - Multiple Misfires
I have a 97 Pontiac Grand Am GT 2.4L Quad 4, my problem is that it misfires and the engine runs rough. You can smell fuel, but there is no fuel leak. I have about 155k miles on the car, never had no serious issues with the car, the car has been great, I’ve owned it since early 2000. Little history on the parts I’ve replaced this year is the following spark plugs x3, spark plug boots x2, timing chain, Timing chain tensioner, camshaft positioning sensor, throttle positioning sensor, fuel pump, fuel filter, air-intake manifold gasket, throttle body gasket, IAC, ignition coils, ignition coil housing, ignition coil wiring harness, swapped the Ignition control module, checked the fuel injectors for solenoid clicking, replaced water pump, thermostat, swapped EGR’s.
Maybe some other parts I can’t remember but I have done a lot trying to figure this out. Also took it to a garage and told them what I have done and the first place they looked was the fuel pump and said it tested at 20psi and called for 40-60psi so they replaced it and problem was still there. They had it for a week and half and couldn’t figure this problem out. Thinking about replacing the ignition coil housing again just to see maybe bought a bad one. Also done the three checks for head gasket blown, milky white oil, anti-freeze bubbling from the reservoir and compression check, all checked out fine. Ran gunk fuel injector cleaner through it several times.
Grand Prix :: 2004 - Loud Clunk While Having The Car In Reverse And Power Braking It
In my 2004 Comp G I have an extremely loud clunk when braking. The braking clunk does not happen all the time. There is a clunk while having the car in reverse and power braking it. While holding down the brake and revving hard and fast it make the loud clunk every time. It will not do it all the time in drive though. I can not pin point which side it is coming from. It sounds as if it is mostly the right. It almost sounds as if it is coming from inside the trans near the pan area?
I have replaced the lower control arms, sway bar bushings, stab links, struts & mounts, I have solid engine and trans and top mounts, new inner and outer tie rods, all wheel bearings, etc.... (not for this issue, just for performance/wear).
I am torn between thinking it is a cv axle or internal drive train noise.
Lumina :: 1994 Chevy 3.1 Stalls When Put In Gear While Engine Warm
A week ago, driving home, the tech started to drop quickly to zero then recover, like the ignition was turned off and then back on. I was able to make it home. The car was due a tune up. I replaced the crank position sensor (OEM), replaced sparkplugs (Autolite Iridium), air filter, fuel filter, no luck. I ohmed the coil packs, secondary resistance showed good, replaced the ignition control module (aftermarket). After this, engine would stall after it was at temp, could restart, once put in gear it would stall, but I could go in reverse and drive home backwards.
Reinstalled original OEM ignition control module. Towed to GM Dealership, mechanic said fuel pump was bad, ignition wires needed replaced, one injector ohmed bad. I took car home, replaced fuel pump (OEM), ignition wires (OEM), no luck. Removed plenum, found pcv valve clogged, and hose kinked, replaced both, ohmed all 6 injectors, 5 injectors read 12.3 ohms, 1 injector was 11.6. Replaced all 6 injectors, (Napa), plenum gasket, still same problem.
GM dealership said computer said no data, they though perhaps ignition control module was bad, but I don't think so. I hooked up my Actron shorting plug, reads code 12 which means no faults, no other codes. I noticed EGR valve has a lot of carbon in the hole, thought about changing it, but I'm really not sure where to go now. The car is a 1994 Chevy Lumina with 230,000 miles, spent about $500 the last week doing brakes, and trying to fix this engine. Where to go from here.
Stalling :: 1994 Volvo 240 Stalls At Idle When Engine Is Warm
My 1994 volvo 240 stalls at idle when the engine is warm. It's happening more frequently as the weather gets colder, I'm not sure if that's a coincidence. The car is an automatic and I'm wondering if it could be something as simple as low transmission fluid.
View 1 RepliesChevrolet - Lumina :: 1994 - Stalls When Warms Up At Stops / Overheating?
My 1994 Chevy Lumina drives great when its in motion but when it warms up it will stall when your at a stop light. It does great at a quick stop, like a short red light or a stop sign but when I am sitting at a long red light it just stalls. It will start right back up but this is annoying. Recently the car radiator was replaced, so the car over heated. What could the problem be?
View 2 RepliesCamry :: 1994 SE V6 Stalls - Code P1300 Igniter Circuit Malfunction
I have 94 SE camry with the 3.0L V6 1MZ-FE engine and has individual coil packs. I'm getting a P1300 Igniter Circuit Malfunction. I have checked it out per the procedures EG2.pdf. I'm down to step 8 and the voltages are little different between the 6 points. started checking out the ground at the ECM per IN36 instructions. it appears that from pin #27 & 28 are not grounded to the ECU case.
View 5 RepliesChevrolet - Beretta :: 1994 - Stalls In Hot Weather Due To High Heat And Humidity
I continue to have problems with my Chevy Beretta. The original problem was that -- after my neice's husband ran the car out of gas -- we had to replace the fuel filter. That was last spring. Afterward the car seemed to run fine until the weather got hot. Now it seems to stall generally in high heat and humidity.
I only paid $800 for the car, and my idea was to get everything fixed on it and drive it a while to get my money out of it. I don't want to go into debt for a car, and I don't want to buy another one (unless I have to). I travel a lot, but I don't need my car for work -- just for personal travel.
A local mechanic has changed the crankshaft position sensor and now the ignition module. I got the car out of the shop again yesterday, but the problem remains. I could barely drive it around the block this evening. The temperature is 73F, humidity is 84%, and dewpoint is 68.
Is this problem definitely weather related? What could be the cause? Vapor lock? An intermittent problem with the fuel pump, filters, or fuel injector? Is it possible to get this fixed for good?
GMC :: 1994 - Reverse Lights Do Not Come On
My reverse lights do not come on when I put my truck in reverse. I got out my multi meter and there was voltage at the switch, so I put a jumper in the connector and the lights lit up.
Thinking it was a bad switch so I replaced the switch, still no lights. So the big question is : what to take apart to find whatever it is that pushes the switch.
The truck details are : 1994 GMC K1500 350TBI 5 speed, the reverse light switch is on the drivers side of the transmission.
GMC :: 1994 - Reverse Lights Don't Work?
Ok so the GMC has another one of those tiny issues that we all hate to have. I don't know if its been this way since I bought it or if its just since we pulled the transmission to put on a new clutch, but my reverse lights don't work. Every other light on the truck works and I checked the bulbs and the fuses and found nothing. I even checked to see if the sensor wire was hooked up to the transmission since we pulled it out and it is.
I have an online subscription to Chilton's and have looked at the wiring diagrams time and time again and can't figure this one out. my real question at this point is how the switch in the transmission works, can I just rewire a bit and direct wire through it or does it have to go through the main harness somehow. the details on the truck are as follows: 1994 GMC K1500 5 speed 350 TBI.
Oldsmobile - Leaks - Cutlassciera :: 1994 V6 Idles Rough And Usually Stalls If Put It In Gear When Start The Engine
I have a 94 Oldsmobile Cutlass Ciera, (3.1L V6 GM3100 engine). When I start the engine it idles very rough and usually stalls if I put it in gear. Eventually once it warms up I can drive it, but when I do drive it's extremely sluggish on accelerations and acts like its about to die. At constant speeds it runs mostly ok. We figured it was a vacuum leak, but we've tried every test we can think of to find it and talked to a couple mechanics and tried their tests and it passed all of them. Supposing it isn't a vacuum leak, then what it might be?
View 4 RepliesFord Ranger / B-Series :: 1994 - Idles Rough / Stalls When Cold But Runs Great When Warm
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesNissan :: 1994 V6 Will Slip Into Neutral When Put It In Reverse Or Drive
i have a 1994 nissan quest 3.0 v6 and when i put it in reverse or drive it will slip into neutral if i am stopped. Also the front motor mount needs to be replaced, which I will do soon. Are these problems related, if not how do i fix the shifter/linkage problem? When driving the vehicle upshifts and downshifts perfectly.
View 1 Replies