Santa FE SM (2001-06) :: 2004 - RPMs Running High / Car Seems To Surge
Mar 17, 2013
2004 Santa fe. Having issues with RPM running high. When car is started, RPM sits at 1500 for a few mins, then drops to 500. Seems to be having issues either getting into gear or staying. At any mph, car seems to surge and not feel like it's getting either gas or power. While on cruise at 55+ mph, car will also surge with RPM dropping 500, then kicking back in. This goes on every few seconds up to random times.
Had it looked at this past weekend at a dealer, and of course it didn't do it one time, after doing it for a half hour prior on the interstate. Tech found no error codes when he checked it as well. Car was fine for an additional 300 miles, then it started again out of the blue. Pulled out at a red light and I though I was going to stall.
Just got laid off so I'm trying to eliminate before putting a lot of money into it if I don't have to. 132,000 miles.
View 2 Replies
Advertisement
Earlier this week, noticed that my car was surging on its own; basically, if I came to a stop, I could still feel the engine, like it wanted to just take off. And if I would have taken my foot off the pedal, it would have done just that. Also, I knew the car had gas, but sometimes, when starting the car it would not start at all. I would have to wait about 5 minutes or so and add major gas to it with the pedal and then finally it would engage. And then the last thing was that when I would get to my destination and put it in Park, the RPMs would go up to about 1500 or so, maybe a bit higher and then stay there and go back down to about 1000, without me pressing on the gas pedal at all. So anyway, thought it was the throttle position sensor, so I had my Dad install a new one on the car. It was a pretty easy process and thought that took care of the problem.
The surging part basically stopped, so the new TPS took care of that, but then it still had problems with starting. Took it to a car repair place the next day and they changed out the spark plugs, said that they were causing a misfire in the engine. Also changed ignition wires and a new gasket. So after they were done, drove away and all seemed to be fine, but then went to the dentist and Parked and then the RPMs went up again. Tried to start it immediately afterwards and it wouldn't start again. Tried a few minutes later, added gas with the pedal and it did start. Took it back to the car repair place, they drove it around, inspected everything and everything checked out fine. (Yeah, of course!) Ok, so just thought maybe the repairs were taking a bit to take effect. But later in the day, wouldn't start again.
So next morning, took it to the Hyundai dealer. They looked at everything for about 2 hrs, and said that there was a vacuum hose that was leaking, so they put on a new clamp but everything else checked out okay. Ok, so now it starts fine every time, but today it did that high RPM thing again when I put it into Park. It doesn't do it every time, but the RPM will just go up randomly then go back down and go back to normal. Should I clean the IAC with some type of carb cleaner to get out any carbon deposits? Or could it be a bad MAF sensor? Not sure what the symptoms are of that. Everything else seems to be okay now except for the random high RPMs when in Park and sometimes at startup too.
It's a 2 WD, V6 engine.
View 3 Replies
I have a 1998 Chevy Blazer (2WD) with 115k miles. When I turn the key and start the car, the RPMs rev up really high for about 4 seconds and then drop down real low until the car dies. All in all this is about an 8-second process, and it sounds like I'm flooring the accelerator when, in fact, I'm not even touching it. The Blazer just started doing this, but previously for about the last few months about once a month, when I would start the car I would get a loud backfire sound which sounded like it came from under the hood (driver's side), and this was followed by the smell of exhaust coming into the cab through the AC vents. How to go about diagnosing this since I'm unable to drive it to get the codes read
View 11 Replies
2004 Santa Fe .... 2.7 6 Cyl 4WD 150k miles
Recently I started experiencing RPMs surging upon startup and driving before my engine warms up. The problem has gotten worse to where I push on the accelerator the RPMs jump to 2700 and the transmission feels like it disengages. My initial thought was the tranny was going bad and slipping. I checked the fluid level in the T and found it was maybe a half Qt. low. I topped it off, but this had no impact on the problem. On a side note, I am able to use the manual shifting feature on the "His and Hers" Shifter and drive the vehicle without any issue. Transmission works fine in manual. The surging RPMs which only occur in Automatic mode, triggered the CEL and I got a code of P0123 which is high side voltage on the Throttle Position Sensor. I replaced the gray TPS with a new black one.
Upon startup the RPMS jumped to 3000 just sitting in Park. I disassembled and reinstalled figuring I had something bound in the throttle. After reassembly the idle went up to 2200, still no good! I reinstalled the original gray TPS and the RPMs, upon starting, RPMs were 1500 with the old sensor...still too high. I did reset the ECU twice during the process of putting in the new sensor and reinstalling the old sensor. Right now I found that when I disconnect the TPS electrical connector, the engine runs normal. It starts right up with the TPS totally disconnected and idles at 750 RPMs! It will not shift to 2nd gear though, when I try to drive it in Automatic Mode. I can however drive in Manual Mode and drive normal and shift right through the gears. Who needs automatic mode right?!!!
View 4 Replies
I have a 2008 Hyundai Santa Fe. Has about 65k miles on it and has regular maintenance and tune ups when needed. It is cared for. The last tune up was about 2k miles ago. Spark plug change, oil change, filters, etc.
I have noticed lately that when the car is moving at idle speeds, it will surge about 200 rpms. It does not happen when the breaks are on or stopped or in park, or moving at higher speeds. It only does it while moving and with no acceleration. It happens in Drive and Reverse.
I live in the city of Lima Peru so a 4x4 is useful but it also requires some tight parking but when it starts to surge, it is a huge pain.
View 8 Replies
So I had this issue with my idling at 1300 rpms but every now and then it would idle at 400 and barley run then one day it didnt want to idle at all so I checked the iac and it was bad so I changed my oil, fuel filter, iac, cleaned my throttle body, fixed a vacuum hose, and cleaned my air filter.
When I started it it idle at 2200 I drove it a little and it dropped down to 1300 the next day I started it and it idled at 800 and staid there for four days now it idles at 2000 then will drop down and surge between 1300 and 1800.
I read that the oil you apply to the filter can contaminate the Maf and you should clean it but a lot of people said the one on a vr4 can't be cleaned while others say it fine. Is there a way to check the maf?
View 1 Replies
Recently replaced plugs/wires on soon-to-be 10 year old '04 SF 3.5L (157K mi.) for the first time.
Plugs were OE Champion Platinum and all 6 looked identical except for excessive gap of .010 +/- due to all the miles. Replaced plugs with same as OE. Old plug wires looked good, but replaced them with aftermarket wires ( fit was as good as OE). Also replaced plenum gasket.
Problem is: engine runs rough at idle and high rpm and appears to be mis-firing. CEL is off and code reader shows no Trouble Codes stored.
View 19 Replies
So my 2005 elantra 2.0 CVVT has 189k on it 1 owner.
I got a check engine light one day and i read the code. Came out to be 02 sensor code bank 1. So i order a denso o2 sensor and replace the part.
I drive the car for about 400 miles to reset monitors and get a check engine light. P0420 cat code. At this point the car drives with normal power and pickup.
1000 miles later my car has lost power. It doesn't have any get up or power when driving normally. I take the car to my local shop and they recommend replacing front cat. I replace front cat, same issue.
At this point i'm not sure if it is a transmission problem or maybe my 2nd cat or something else?
On the freeway if I put my pedal to the ground the rpms surge up very very slowly,
Also seems like the car doesn't shift till around 4k rpms, seems like previously it shifted sooner.
View 10 Replies
My mother has a '04 Santa Fe 3.5. Her automobile makes a rattling/grinding sound when around 1000rpms/idle. However, the sound disappears when accelerating and drives like a charm. The sound returns once again around 1000rmps at idle or stop. I have changed the oil pan, replaced oil and filter and even put in a new battery. I'm not an aficionado when it comes to Hyundais (Subaru driver here).Car also has 180k miles.
View 6 Replies
On light acceleration, it has a light stumble or surge and is very slow. On hard acceleration it makes a lot of noise, but isn't even fast enough. I can feel it shift through the gears, and can feel the converter lock up when it's supposed to. Any attempt to climb a slight hill or pass a car, it downshifts to what seems like 2 gears down, and has a loud roaring noise, but I don't feel the acceleration. At steady speed, it feels like it's hunting for a steady RPM, but can't find it.
I just had a timing belt replaced. Had the mech double check to make sure marks are correct. He did a cranking compression test and said they were all between 165-170 psi (is that a little high for a 150K mile car?). He smoke tested the intake system and found no leaks.
It does have codes stored for cat converter and a lean code-bank 1.
View 5 Replies
Came out of my house and my 04 Sante Fe will not stay running. It worked fine on the way home form work won't stay started now. You can give it gas and everything but it just dies out after a few moments. I checked most of the basics...
-Fuel pump runs when key is on
-Added gas, over 1/4 tank
-Checked engine fuses
-removed air filters and hoses
-removed mass air intake unit
-down to throttle body and such,
-to keep running by spraying gas directly into engine?
-removed fuel pump under seat
-checked mesh filter and connections
-clean no build up no visual problems with pump or filter
-checked cut off switch, not activated
-removed gas line from injector rail getting good "squirting" from rail
I have asked everyone and most think it is some kind of sensor but I have no light on and I have put it on the OBII and no error codes are found unless I un plug one of the many sensors, which i have done to a few to check them (air mass intake).
View 2 Replies
I'm having trouble diagnosing a high RPM in park and neutral on my 2004 Santa FE 4WD 2.7L. Idle's great in drive and reverse. Occasionally when I start the car up it will shoot up to 3000 RPM until I shift into drive or reverse with a heavy thunk. Then it drives fine. When I shift back into park when I'm done driving, it will shoot back up. To avoid this, I just shut the car off in drive and then shift to park.The weird thing is, sometimes it doesn't happen at all. Sometimes it starts right up and shuts down with perfect idle. However, once I give it some throttle in park in these instances, the idle will jump back and forth between 1500 and 2000 and won't die back down to 800 where it should be until I shift into drive or reverse. Not sure what's going on.
I've replaced the idle air control valve, purge valve solenoid, and camshaft position sensor, but to no avail. I also replaced the throttle position sensor a few weeks ago, but that didn't seem to do anything, so I took it back. I'm wondering if I maybe didn't do the correct installation procedure. I still have the old grey TPS for what it's worth. Should I change this? I've also played with the tension in the throttle cable, but I don't really know how to get it exactly within specifications. I definitely removed some slack. I just checked for vacuum leaks using the cigar method with a hose from the PCV valve with the throttle body sealed with saran wrap, but I couldn't find anything. My method was shoddy, and I don't really know what I'm doing, so I wouldn't rule out a vacuum leak by any means.
View 1 Replies
Ok, so I'm working on a 2004 Hyundai Santa Fe, 93,000 miles. The vehicle runs great! So great that you cant get it to stop running!! The problem is intermittent and generally happens after the vehicle has been running for at least 3 minutes. I turn the key off and she keeps on running (not dieseling, but running at 340-450 rpms!) I have already removed the aftermarket remote start that was installed on the vehicle thinking that was the problem, it was not. Then I went to the ignition switch and unplugged that, also to no avail! I plugged my scan tool in and can communicate with the computer and view pids while the key is on. When I turn the key off, I should loose communication. When everything acting normal and the car actually shuts off with the key, I loose communication with the computer upon turning the key off. When I turn the key off and the veh. keeps running, I do NOT loose communication with the pcm. The only way to shut the car off is to step on the gas pedal. Otherwise it'll run at 400 or so RPM for an hour or so!!
View 8 Replies
For about 3 years, our SF (about 125,000 miles) has experienced the whirring/whining upon acceleration whenever the AC was running. I didn't do anything about this as the AC still worked well.
Just a few days ago, while running the AC for a "recharge" during our recent cooler weather, I realized that the AC was not cooling below outside ambient temperature, nor was the whirring present any more. I assume that the compressor finally seized. (?)
To keep repair costs low, and based upon the description above, where should I begin to look to see where the problem lies? Is it most likely a seized compressor/clutch? I am unsure if this is the issue, since even when driving with the AC turned to "Max", I now notice NO detrimental effects upon the engine/power output, which makes me wonder if the compressor actually seized. Wouldn't a seized compressor actually be very hard for the belt to turn, or possibly burn the belt?
I know the compressors and AC systems on these cars are notorious for dying too soon...
View 7 Replies
2004 2.4l engine has high idle speed aprrox. 1000rpm.
View 2 Replies
For about a year now my 04 santa fe whines after running for a long ride. We can never get it to do it to bring to dealership to have them look at since it only does it after long rides. We have had the power steering and transmission flushed and that worked a little while during the fall and winter but now that the weather is getting warmer it started again. What this could be?
View 1 Replies
I recently replaced timing belt and balance belt on my 2004 santa fe 2.4l and now the engine runs like crap and shakes badly. I went over all timing marks again and again and I am at a loss.
View 9 Replies
I don't own a VW, but my friend does, and she knows absolutely nothing about cars. She drove me home from a friend's house today, and I noticed her car was sitting at insanely high RPMs, even though we were only going like 60-65. The car was ranging from like 4500-5200rpms the entire way home, and the engine sounded like a lawn mower.
Don't know many details on the exact model of 2002 jetta it is (I'm a subaru guy) but it's an Auto. I was convinced she had it in 3rd the entire way instead of drive. I asked and she said it was in drive, but I was sitting in the back so I couldn't quite tell. Not sure how being in 3rd works on an automatic, but she could still come to a full stop. The car was pretty much constantly sitting at above 3k whenever it wasn't at a full stop though. Like, after letting of the brake at a stop light, and pressing the gas, it'd pretty much immediately flick up to 3k and never go below.
So, not sure if this is normal for these cars, but I thought it'd be worth asking since it would suck for her if this could have been fixed earlier. My subaru sits at 3k when I hit 60, and only hits 4k if I'm going like 80, so I just thought this seemed pretty weird.
View 8 Replies
I have a 2001 chevy metro 4 cyl. with 13 inch wheels and automatic transmission. The engine rpm's are running high at highway speeds. Would a larger diameter wheel support this situation?
View 8 Replies
My parents are having trouble with there 2008 Santa fe 3.3 L. The transmission won't shift and the rpm's climb really high. Does that mean the transmission is going or is it something else.
View 15 Replies
We have a 2006 Santa Fe Hyunda with 100,000 miles that when we hit 80 mph on the highway the rpms drop to zero and stay there. We just had the camshaft and crankshaft replaced. Why this is happening?"
View 3 Replies
