Santa FE SM (2001-06) :: High RPMs In Park And When Starting
Sep 16, 2012
Earlier this week, noticed that my car was surging on its own; basically, if I came to a stop, I could still feel the engine, like it wanted to just take off. And if I would have taken my foot off the pedal, it would have done just that. Also, I knew the car had gas, but sometimes, when starting the car it would not start at all. I would have to wait about 5 minutes or so and add major gas to it with the pedal and then finally it would engage. And then the last thing was that when I would get to my destination and put it in Park, the RPMs would go up to about 1500 or so, maybe a bit higher and then stay there and go back down to about 1000, without me pressing on the gas pedal at all. So anyway, thought it was the throttle position sensor, so I had my Dad install a new one on the car. It was a pretty easy process and thought that took care of the problem.
The surging part basically stopped, so the new TPS took care of that, but then it still had problems with starting. Took it to a car repair place the next day and they changed out the spark plugs, said that they were causing a misfire in the engine. Also changed ignition wires and a new gasket. So after they were done, drove away and all seemed to be fine, but then went to the dentist and Parked and then the RPMs went up again. Tried to start it immediately afterwards and it wouldn't start again. Tried a few minutes later, added gas with the pedal and it did start. Took it back to the car repair place, they drove it around, inspected everything and everything checked out fine. (Yeah, of course!) Ok, so just thought maybe the repairs were taking a bit to take effect. But later in the day, wouldn't start again.
So next morning, took it to the Hyundai dealer. They looked at everything for about 2 hrs, and said that there was a vacuum hose that was leaking, so they put on a new clamp but everything else checked out okay. Ok, so now it starts fine every time, but today it did that high RPM thing again when I put it into Park. It doesn't do it every time, but the RPM will just go up randomly then go back down and go back to normal. Should I clean the IAC with some type of carb cleaner to get out any carbon deposits? Or could it be a bad MAF sensor? Not sure what the symptoms are of that. Everything else seems to be okay now except for the random high RPMs when in Park and sometimes at startup too.
It's a 2 WD, V6 engine.
View 3 Replies
Advertisement
05 Santa Fe, 2.7 liter, 71,000 miles
Prior to today it had revved high, up to 3000 RPM, once or twice upon start-up but then settled down once I started driving it with no issues at stop lights.
Today, however, no issues upon start-up but within 1 mile it started acting badly. Pulls strong under load, i.e, accelerating. Once cruising speed is achieved and the right foot is relaxed, it loses power, slows and bucks.
At stop lights revs are down to below 800 while in drive and is slow out of the gate. When put in neutral at stop lights, it revs to 3000 then falls to 2000 then back up to 3000. It does not stall.
Replaced the IAC and it ran fine in park for exactly 2 minutes then began revving again.
View 3 Replies
My 2001 Hyundai Santa Fe has recently started idling very high when put in park or neutral. While in drive the engine idles above 1K and you need to keep your foot on the brake to keep from moving forward. If you shut down the vehicle while idling high, the car will not start right away. It needs to cool down for 10 -15 minutes before restarting. It will run fine for awhile but will go back to revving up again.
View 7 Replies
I'm having trouble diagnosing a high RPM in park and neutral on my 2004 Santa FE 4WD 2.7L. Idle's great in drive and reverse. Occasionally when I start the car up it will shoot up to 3000 RPM until I shift into drive or reverse with a heavy thunk. Then it drives fine. When I shift back into park when I'm done driving, it will shoot back up. To avoid this, I just shut the car off in drive and then shift to park.The weird thing is, sometimes it doesn't happen at all. Sometimes it starts right up and shuts down with perfect idle. However, once I give it some throttle in park in these instances, the idle will jump back and forth between 1500 and 2000 and won't die back down to 800 where it should be until I shift into drive or reverse. Not sure what's going on.
I've replaced the idle air control valve, purge valve solenoid, and camshaft position sensor, but to no avail. I also replaced the throttle position sensor a few weeks ago, but that didn't seem to do anything, so I took it back. I'm wondering if I maybe didn't do the correct installation procedure. I still have the old grey TPS for what it's worth. Should I change this? I've also played with the tension in the throttle cable, but I don't really know how to get it exactly within specifications. I definitely removed some slack. I just checked for vacuum leaks using the cigar method with a hose from the PCV valve with the throttle body sealed with saran wrap, but I couldn't find anything. My method was shoddy, and I don't really know what I'm doing, so I wouldn't rule out a vacuum leak by any means.
View 1 Replies
2004 Santa fe. Having issues with RPM running high. When car is started, RPM sits at 1500 for a few mins, then drops to 500. Seems to be having issues either getting into gear or staying. At any mph, car seems to surge and not feel like it's getting either gas or power. While on cruise at 55+ mph, car will also surge with RPM dropping 500, then kicking back in. This goes on every few seconds up to random times.
Had it looked at this past weekend at a dealer, and of course it didn't do it one time, after doing it for a half hour prior on the interstate. Tech found no error codes when he checked it as well. Car was fine for an additional 300 miles, then it started again out of the blue. Pulled out at a red light and I though I was going to stall.
Just got laid off so I'm trying to eliminate before putting a lot of money into it if I don't have to. 132,000 miles.
View 2 Replies
2004 Santa Fe .... 2.7 6 Cyl 4WD 150k miles
Recently I started experiencing RPMs surging upon startup and driving before my engine warms up. The problem has gotten worse to where I push on the accelerator the RPMs jump to 2700 and the transmission feels like it disengages. My initial thought was the tranny was going bad and slipping. I checked the fluid level in the T and found it was maybe a half Qt. low. I topped it off, but this had no impact on the problem. On a side note, I am able to use the manual shifting feature on the "His and Hers" Shifter and drive the vehicle without any issue. Transmission works fine in manual. The surging RPMs which only occur in Automatic mode, triggered the CEL and I got a code of P0123 which is high side voltage on the Throttle Position Sensor. I replaced the gray TPS with a new black one.
Upon startup the RPMS jumped to 3000 just sitting in Park. I disassembled and reinstalled figuring I had something bound in the throttle. After reassembly the idle went up to 2200, still no good! I reinstalled the original gray TPS and the RPMs, upon starting, RPMs were 1500 with the old sensor...still too high. I did reset the ECU twice during the process of putting in the new sensor and reinstalling the old sensor. Right now I found that when I disconnect the TPS electrical connector, the engine runs normal. It starts right up with the TPS totally disconnected and idles at 750 RPMs! It will not shift to 2nd gear though, when I try to drive it in Automatic Mode. I can however drive in Manual Mode and drive normal and shift right through the gears. Who needs automatic mode right?!!!
View 4 Replies
UK 2.2 Diesel
Problem for about 3 years. Always starts in neutral, rarely starts in park.
Any possible cause. Maybe a micro switch or a cable adjustment.
View 8 Replies
2002 Elantra engine is revving up to 3000 rpms when in neutral or park. I changed the Throttle Position sensor and it went right back to revving up. Code read P0121. What might be causing this? Seems like I get one thing fixed and then another code shows up..
View 2 Replies
My parents are having trouble with there 2008 Santa fe 3.3 L. The transmission won't shift and the rpm's climb really high. Does that mean the transmission is going or is it something else.
View 15 Replies
I have been getting a 2006 Santa Fe GLS A/T back on the road for friend who let it sit for almost 2 years because the bumper had gotten knocked off. I charged the battery to get the car to start and it started up OK, but the front brakes were shot completely. I then proceeded to replace the front brake pads and rotors, and when I went to start the car again I noticed something peculiar.
The car wouldn't start, or even attempt to (didn't here it cranking at all). I know the battery is good, and all the other components in the car turn on when I turn the key to A/C setting. I have the shift lever in what would seem to be Park, but the light on the console shows it is Reverse. It shows the car is in reverse when I have it in Park or Reverse, and shows Neutral when I have it in Neutral.
Before I did the brakes (which I don't believe to be related) it was being a bit fussy about switching gears and going into park, but it was definitely working.
View 10 Replies
We have a 2006 Santa Fe Hyunda with 100,000 miles that when we hit 80 mph on the highway the rpms drop to zero and stay there. We just had the camshaft and crankshaft replaced. Why this is happening?"
View 3 Replies
A buddy of mine has a late 2000 passat 2.8. He recently developed a bad knocking at higher RPM's. I took a look at it and it is coming from the bottom end of the motor (rod bearing, crank bearing?) He has no loss of power and the knock is not there at idle.
View 2 Replies
2001 elantra has been revving really high on cold starts, RPMs will stay at over 3000 till u switch it into drive or reverse, Never happens when engine is warm, had intake cleaned out, did not solve issue...
View 5 Replies
Two times in the last month my 2003 Sante Fe would not start - the radio, air conditioning would come on but nothing from the engine - not even a click - no check engine light. Had it towed both times - as soon as it was towed it would start up. It seems to happen in 2 week intervals. Now I realize bc they had it in neutral to get on the truck that is what facilitates it start. It hasn't happened in a week but I know it will again.
View 1 Replies
1614 - Powertrain Control Module (PCM) harness is open or shorted - Faulty Electronic Throttle System (ETS) unit - Faulty Powertrain Control Module (PCM)
1191 - Electronic Throttle System Limp Home Valve On
Car is a 2004 santafe 3.5l automatic. symptoms are phantom revving up to 3-4k in park without me doing anything, sometimes car is hard to start, idle is very erratic/doesn't want to stay running. other times it starts and drives perfectly. from what i can gather this is some sort of malfunction in the electronic throttle system, and from searching people say "inspect ETS system", but i'm not sure what this involves. i unplugged every sensor i can locate in relation to the throttle system, cleaned them with electronic spray cleaner and put some di-electric grease. reset the ecu through battery disconnect, and problem came right back. local shop pulled the codes and said it'll be about 1200 for a new throttle body, and that the dealer has to reset it say what.
is there anything i can do with this sans bringing it to the dealer? i'm not even sure it would make it that far, driving home from the local shop it was in limp mode and i could only drive about 30 mph, and barely made it up hills. probbaly take me three hours to drive to the nearest dealer lol.
i replaced the accelerator pedal sensor about a year ago, and it also threw a code for throttle position sensor about a year ago also.
View 85 Replies
The other day I was driving my Santa Fe. I noticed the RPMs went up and then the car started slowing down, so I pulled over. Since then the car won't drive. Engine starts up but the car won't move at all. When I push the gas pedal I hear the engine revving, but no movement in drive or reverse. No check engine light, and I checked the transmission fluid, looks and smells good. I checked and it has no transmission pressure. I verified by removing the transmission cooler lines and shifted the truck in all gears. Nada. Could it be the filter, a sensor or the torque converter? Or am I looking at having to replace the whole transmission?
View 21 Replies
This all started out when I wanted to change my original plugs that had 200k miles on them. I have that part done now and new wires. Then it wouldn't start without me starting it while holding the gas pedal down. Then I would have to press the pedal down or it would die.
I may need to clean the throttle body. I bought some Valvoline Throttle Body Cleaner and cleaned the throttle body it was black inside and now it's nice and clean. After that the car starts up fine except on the first try. It starts up and idles at around 2,000 rpms. When I press the brake it drops to 1,000, then back up to 2,000. The strangest part is I have no acceleration power now. I can press the pedal to the floor and it will only go to 3,000 rpms. It will slowly get faster as I drive but there's no immediate response when I press the pedal down.
Why would cleaning the throttle body do this? It throws a code when I first start it and it dies the P1110 code but I think that is because the rpms are at 600 when it catches it. No misfire codes or anything, so I think the plugs and wires are working. Just the faster than normal idle now and no power when I press the pedal down.
Would the throttle body cleaner hurt the throttle position sensor?
View 7 Replies
Isn't the park gear selector indicators suppose to me illuminated when you turn on the lights, mine aren't. Why?? stick shift between seats on floor.
View 5 Replies
2004 Santa Fe 3.5 has started idling rough when in park or when stopped and in drive. When I'm actually driving, it runs smooth and doesn't seem to have any issues or hesitation. I tested my EGR valve with a vacuum pump and it held 7Hg of vacuum and did not leak. I think that indicates it is working still?
I think my issue may be the EGR Solenoid, but I'm not sure how to test it. When I remove the Green hose from the Throttle Body, there is a good vacuum coming from it and my car speeds the idle up and seems to run smoother. I think that means there's some kind of blockage? When I have the Solenoid off, you can blow through it, which I think means it is open.
I think I have to replace the Solenoid, but didn't want to just buy parts.
View 6 Replies
what would cause a pulsating rough idle when in park with the defrost or a/c on? when I turn it off or to any other position it's fine even when I turn if off it's fine as well? there is no Check Engine Light showing at this point.
View 7 Replies
What can I do about my car it's not shifting, it's stuck in high gear and when I go from park to reverse it makes a loud thump. The check engine light came on and the codes are transmission control module it's a 2006 and only has 30,000 miles on it. It's hard to believe it's the brain so we changed the fluid and cleaned the sylinoids but then when I drove it around the block I put it in reverse it didn't make the loud noise and it shifted fine for a minute before I got around the block and almost home it made a loud banging noise and went back to not shifting again. What the problem could be.
View 5 Replies
