Santa FE SM (2001-06) :: Lost High And Low Beam But It Works If Hold The Lever Back?
Jul 8, 2014
I'm trying to troubleshoot an odd issue.
When the lever is in low beam mode I have no headlights or fog lights. (parking lights fine.)
When the lever is forward in high beam mode I have no headlights or fog lights. (parking lights fine.)
But if I hold the lever back in "fash the high beam" mode the high beams turn on. This got me home last night, but I don't know where to start looking for the issue?
Faulty relay? Faulty switch? Something else?
(2004 Santa Fe)
View 14 Replies
Advertisement
I have a 2012 Hyundai Accent GLS and recently noticed that my low beam only works in the high beam setting and the high beam doesn't work.
View 10 Replies
My roommate has a 2006 S60 Volvo. One day the passenger turn signal just stopped working. It only works if the high beam is on. The driver side turn signal works fine and so do the emergency flashers. It's not the bulb, not the fuse, not the turn signal lever, and she even took it in the shop and they couldn't figure out the problem without replacing the DIM which would cost a lot.
View 1 Replies
Golf mk7 2013 ... All of a sudden I lost the highbeam. Highbeam "flash" still works, but not constant high beam.
Bulbs? Are they separate between flash and constant?
Relay?
Stalk?
View 10 Replies
I have an 01 f350, my reverse lights only work when I hold up my shifter, like its almost into park. I think my reverse light switch is bad, but I don't know where its located.
View 6 Replies
I have a 2006 elantra. I just got it back from having a new clutch put in. My passenger side headlight, low beam, no longer works. I tried two different new bulbs and it still doesn't work. All the other lights on the car are working, including the high beam and running light on the passenger side. Is there something that would have been disconnected when they replaced the clutch? Is there something I should check?
View 1 Replies
I have a Santa Fe 2001, 2.0 Crdi.
My low beam have shut down. I have checked the fuse for right and left, and as I can see, it's the same fuse as for the high beam ...
Is there any known problems regarding this faults ? Of course, the bulbs are ok ...
View 9 Replies
The A/C in my 2001 Nissan Pathfinder (~153,000 miles) only works on high as of this afternoon's commute. This seems like a common problem on older cars - what's the typical cause? Googling just gives me all sorts of answers and I would like to have some background before calling our mechanic.
View 6 Replies
My high beam indicator in my dash is not working, I pulled the bulb and checked it and it is fine, so I did a voltage test and I am only getting 1.5 volts at the light terminals, I should be getting 12 volts. Is there a wiring diagram someone has so i can see if it is the dash display itself or that I could trace back to the switch to see if it is something in the headlight switch? or What it could possibly be. other than that, everything else works.
View 3 Replies
I've owned my 2003 Santa fe v4 for about a year and a half now. One thing that has always bothered me in the fact my air condition works on only two out of four levels. Level 2 and Level 3 work perfectly, but level 1 and level 4 dont work, and have never worked.
I've gotten a lot of things replaced, but never bothered with this as I barely use it anyways (windows down + high speed = just as good).
View 13 Replies
I have a low beam that just isn't working at all on the right side. I changed the bulb 3 times now, confirmed I had the right dual beam bulb (Sylvania 9003) and still the same result. The low beam doesn't work on the right side, but the high beam works.
2002 Hyundai Santa Fe GL 2.4 CYL ...
View 9 Replies
My car is fully stock, with all options available to me (cold weather package not available here). The low-beam triple-LED headlights are aimed way too low compared to all my previous cars, and where they should be. BUT high-beam is aimed properly. So if I adjust the low-beams up, my high-beams might end up lighting up the trees, not the road.
If adjust the headlights up on a fully stock car (not lowered at the front)? Are the high beams still lighting up the road fine? And if you can be specific as the number of turns on the screwdriver, it'd be good too to have an initial adjustment reference.
View 3 Replies
This morning a dash light informed me a headlight bulb was out. It was my DTR light on the passenger side.
I purchased Sylvania H7 high intensity, installed it and it failed to work properly. Daytime light on only drivers side works.
High Beam on , both lights works.
I checked my manual and it said to check fuse in the 5 slot on the driver side dash/door panel and there actually is no fuse in there. I checked the driver side and there was no fuse there either.
I replaced my driver side bulb last year and it took 5 mins....i am already 4 hours into this!
View 4 Replies
I drive a 96 Subaru Legacy. What does it mean when one of the high beams is dimmer (less light output) than the low beam? I am using a brand-new bulb. It's not an adjustment issue because I was looking at the bulb when it was outside of the housing and it clearly gets dimmer when you switch to brights. However, they are equally bright when on low-beam, so I don't think its just a crossed wire.
View 2 Replies
I replaced the low beam and high beam on my Subaru, now the low beam is very dim and the high beam doesn't work. Careful not to touch the bulb.
View 3 Replies
Low beams don't work. The fuses are fine (under the dash, and in the engine compartment) and the bulbs look good. The fact that both went out at the same time has me wondering. One post on this forum for something not related mentioned a headlight relay behind the fuse panel?
View 9 Replies
I have a 2001 f250 with factory fog lights. ive been researching to see if I can make my fog lights turn on with the high beams without pulling them out. My broke and cant pull it or it comes off, but will still work to turn head lights off and on. How to make them come on with the high beams?
View 14 Replies
I have an Air Conditioning issue on my 2004 Santa Fe, 2.4L 5-speed manual with 208,000km on it. I've never had any work done on my AC since I bought it new. Never had a problem with it and even as I write this is works just fine and blows ice cold air.
The problem started a couple of weeks ago when I noticed this very brief "higher pitched burping sound" coming from under the hood that lasts for just a second, and only when the AC is on and only if the RPM's are above idle. It sounds like a "bloop" for lack of a better description. When it happens, the RPM's drop one mark on the RMP gauge for a moment and there is obvious strain on the compressor. Air remains ice cold, everything still works, but this occurs every 30 seconds or so while driving.
While stopped I can rev the motor to just above idle, say 2000rpm and engage one of the defrost settings and get the "bloop" sound to occur almost every time. The top thicker AC pipe leading into the firewall from under the hood (the one that gets cold to the touch) seems to be part of the problem. At least if I am touching this pipe when it makes this "blooop" sound I can feel the vibration from the "bloop" in this pipe.
I've already had a garage replace my AC belt which I just had replaced a month ago, and checked the pullies and tension and all is okay. So it's definitely coming from the AC system and I can feel a vibration during the "blooop" sound on that pipe that gets cold and goes through the firewall. The sound does not occur when the AC is not on.
Also, when I am driving and it occurs every 30 seconds I do feel a slight decrease in the smoothness of the ride and like I said when it does this the RPM's will drop one mark on the gauge, which I'm assuming is the strain on the motor trying to engage the compressor when it's probably already up to pressure.
View 2 Replies
I have a strange problem. My driver side low beam dont work and my right side high beam dont work. Try different relay (switching), check fuse, bulb etc. Also in my dashboard the right green arrow for the flasher always still on(solid).
If I activate (with the control arm) the right turn flasher the flasher light blink in the dash board and my outside flasher bulb flash but my left high beam also blinking in the same time!
View 3 Replies
I'm currently our of town, and will be so for several months. With that said, my wife told me today that when she pushes the lever forward for the high beams that nothing happens, but when she pulls it to the rear (as if she were only flashing the high beams) they work fine.
I figured I could either order parts while i'm away or start doing a lot of homework to find possible issues/fixes.
View 9 Replies
I have 2005 Santa fe. I replaced the battery about 1000 km (about 600 miles) ago. Interior lights are bright. Now the car won't start, starter doesn't crank at all. At first I thought that it's an immobilizer problem, but not so sure now.
Could you tell me how Hyundai's immobilizer works. Some other cars starts but then turns off if immobilizer is on. Is it the same thing with Santa Fe?
I read from the manual that immobilizer-light should blink if immobilizer is on. I have not watched the dashboard lights so accurately before this. When I turn key to position "on", the immobilizer-light turns on (it doesn't blink). Is it supposed to do so and turn off when the car is running? Or is that a sign that immobilizer is on?
View 1 Replies
