Ford - Ranger :: 1990 - Voltage Gauge Will Flicker And Jump Around When Starting


Apr 8, 2013

We have a 1990 Ford Ranger - 2WD 4cyl - sometimes when we try to start it, it will not kick over the final time for several tries. When it finally catches the voltage gauge will flicker and jump around. When the gauge flickers, the truck will shut off...then the same issue with trying to start it again. Some days it runs just fine and others it will stall out 3-5 times in a 15-20 minute drive. We have been told it's the DIS Module OR the Crankshaft Position Sensor OR the Voltage Regulator OR .....

View 2 Replies

Advertisement

Ford Ranger / B-Series :: 1990 - No Spark And Not Starting

1990 ranger 2.9 ... I have put about everything new on this ranger. It has no spark, ran fine til i went across a set of railroad tracks, it died 6 months ago and never started again .. Many dollars and many hrs has gone into this thing and still no spark. It will spark when you turn the key on. Crank it and 3 more sparks and thats it. Every electrical piece has been replaced. I've checked and bought relays ,fuel shut off, new distributor pickup coil, rotor, cap, wires, plugs, coil and still no start?

View 6 Replies

Ford Ranger / B-Series :: 1990 - Starting And Dying / Ticking In The Engine Compartment

I'm having a rough go with my little 1990 Ranger Custom. Let me get into the signs and symptoms I'm finding, The Truck is having starting and dying issues. It has plenty of Gas. It is completely erratic when it dies. I'll be driving along and suddenly, as if turning the key off, it dies. No sputtering of the motor, no clicking or clacking or growling anywhere. Just a clean sounding turn off. The odd thing is, I'll leave it for a few hours, and the problem disappears. I can drive it for one to 30 minutes and then it can die again.

Now it's sitting in my driveway I am rough on the truck, because its a work truck that I use to drive down to my job site. So, farm pasture, fields, woodland paths and tractor access roads. I checked to see if the pump plug was unplugged. But it's very plugged in. The entire fuel system is just less than a year old, and I am very good friends with the old owner and he can't figure it out either. Could I be having ignition problems? There is a ticking in the engine compartment that isn't very noticeable, only noticeable when the hood is up and motor running, but that has always been there since I've had it. I heard that sometimes the safety switch on the firewall turns off the fuel system in case of accident.

Could that have gotten agitated? I've been having this issue for a little while, after I drove it in the rain for an hour and half. It was pouring rain. I ran out of gas the day after (because my fuel gauge doesn't work) and I used a Jerry can filled with gas to get it to the gas station. I didn't sift the gas, but I don't see it having debris either. Could I have water in the system? I put injector cleaner in my tank and more gas to try and dilute the system but, that doesn't seem to have worked...

View 14 Replies

Toyota - Corolla :: 1990 - Fuel Gauge Rises After Starting The Engine

On my early 90's Corolla, when I turn the key to "on" but don't start the engine, the fuel gauge will -- for example -- read 1/4 full. It will stay at 1/4 indefinitely as long as the engine isn't running. Then when I start the engine and drive the car for a few minutes, I notice the gauge has gone up, so it will be reading 3/8 full within 5 minutes of driving. And I don't have to be moving, once it gets to 3/8, it says at 3/8 whether moving or idling at a stoplight. It has always done this, even since the car was new. It's not a problem, but I've always been curious what causes the fuel guaue to rise like this.

View 9 Replies

Ford 6.0L Power Stroke Diesel :: ICP Voltage To Jump Around A Lot At Idle Or While Cruising Or Accelerating

Just a quick question but is it normal for the ICP voltage (ICV) to jump around a lot at idle or while cruising or accelerating? Started watching this pid and not sure what's normal and what's not.

View 13 Replies

Ford Excursion :: Needle Started To Stumble / Flicker When Boost Gauge Reached At 15 PSI?

So driving over the pass last weekend, I noticed as I reached about 15 psi on my boost gauge the needle started to stumble/flicker and I could audibly hear a "pffsssfftst" at that same time, back down away from 15lbs boost and the noise goes away? I am leaning towards a boost leak, it sounded like it was coming from the driver side anyways. I hate to just assume it is something, and mindlessly throw parts at it, on the other hand I know that is one way to start replacing old worn out parts.... So I am thinking start at ordering some new CAC boots from riffraff, anything else I could consider? Could be a worn out spring on the wastgate?

View 14 Replies

Ford F-150 - 1997-2003 :: 1998 Truck Not Starting / Not Getting Voltage At Fuel Pump

I have a 1998 Ford F150 with 4.2.. Started off a intermittent problem of not starting acct no fuel. Now will not start at all. Checked all fuses and relays.. Am not getting voltage at fuel pump. Changed ECM thinking that was the problem.. Have checked all multi wire connectors for corrosion and tightness. Am at a lost what to try next.

Also, not sure if its related or not. The turn signals and hazard flashers do not work. When I turn on the hazard flashers, nothing happens. If I leave the flashers switch on, the turn signal work. Checked all fuses and relays and they appear good.

View 2 Replies

Ford 7.3L Power Stroke (1999-2003) :: Temp Gauge / No Voltage At Sending Unit

I've read some treads on the temp gauge sending unit but I'm a little foggy on where to look for my problem. I just purchased a 2000 F250 7.3, temp gauge not working. It has a new sending unit. I read some threads about the voltage at the plug but I have no voltage on either side of the plug. The way I understand it red/white wire goes to the battery. Is there a fuse between them and which one is it? and if fuse is ok is there a cronic problem that someone might know of that I can look for?

View 7 Replies

Ford 6.7L Power Stroke Diesel :: Jump Starting With Dual Batteries

If I'm giving a jump:

Assume I hook positive and negative cables to the respective terminals of one of the two batteries. The alternative would be hooking positive cable to one battery and negative cable to the other battery, or does that make 24 volts? I'm also assuming if it is just the one battery, it does not matter which one you jump from?

If I'm receiving a jump:

I assume positive cable to positive post of one battery and negative cable to a good ground under the hood somewhere? Again, does it matter which battery I use? I wonder where a good ground is on this crowded diesel engine and aluminum body. Front radiator supports?

View 14 Replies

Ford F-150 - 1997-2003 :: Fuel Gauge Malfunction - Jump Up All The Way To Full When Started

I have a 97' F-150 4.6 L and I've been having some fuel gauge issues.... I filled up my tank up and I drove it 130 miles and it still said full tank... even when I had 1/2 I would start it and every time I started it it would jump up all the way to full and slowly drop down. Then randomly last night it started working... I noticed as I hit rough patches in the road and bumps it would usually fluctuate, but it would also fluctuate up... It read I have 3/4 tank last night and I go to start it today and its back up to full! I don't understand... Wouldn't a bad sending unit just stop all together?

View 1 Replies

Ford Ranger / B-Series :: 2000 - Battery Light Will Flicker Especially If Under A Load

2000 Ranger 2.5L. Recently driving up and down road to work about a half hour in to drive the battery light will flicker especially if under a load (AC on, lights on)etc... Assuming it is the alternator/voltage regulator getting ready to FAIL. Plan on replacing alternator this weekend? What to do or check something other than replace the alternator?

View 5 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 E450 - Low Voltage On Gauge With Good Battery - No Start Condition

2000 Ford 7.3 E450 120,000 miles...

I have changed the CPS twice
I have checked the resistance of the injectors at the IDM connector with a volt meter and the harness reports back good.
The truck will run with ether for a few seconds
I have changed the fuel filter.
The fuel bowl fills quickly
I have unplugged the ICP.
The truck is showing low voltage on the gauge with a good battery. Around 10v
I have connected my 200amp car starter and I never see over 10v. I plan to check the grounds, but I am at a loss.

Everything is difficult because this is a van body so space is limited. I have also plugged in the block heater for an hour and that hasn't made any difference. Where can I get the best price on an AE scanner.

View 14 Replies

Ford Ranger / B-Series :: 1993 - Getting 157 / 158 And 159 Codes - Mass Air Flow Voltage?

Truck is a 1993 ranger 4.0 ohv

Ok I have been getting 157, 158, and 159 codes. I have cleaned and replaced the MAF with no success. I checked the voltage to the sensor 12v, checked the voltage from the signal wire and it is to high. It has been high on the cleaned unit and on both replacements, so I am thinking it is not the MAF, but what will cause it to register high. I cant get the signal voltage below 1.9V at idle.

Signal also reads high with the ignition on and the engine off. What would cause the voltage to be high, I have read it could be an IAC but I would think that would not effect it with the engine off.

View 14 Replies

Golf VI R :: How To Set P3cars Gauge To Read Battery Voltage

The P3cars gauge to read battery voltage is misleading since it is reading the voltage when the alternator is running. How do i get it to read the actual battery voltage without the engine running?

View 6 Replies

Ford Transmission :: 1990 F250 - Sluggish When Starting Off In Drive

Automatic transmissions! I have a 90 F250 4x 7.5 and E4OD. I have been chasing electrical gremlins, and I'm not sure if these problems are related or not. Symptoms: When starting off in drive, it feels very sluggish, as if it is starting in second gear. Manually putting in first works. When left in drive it will drop all the way into fourth at 20-25 mph. If left in drive, when you turn a corner and step into the throttle the trans will rapidly shift up and down causing a surging effect. Manually moving the shift down into second stops this. I have been considering swapping the PCM from an 89 7.5 E4OD parts truck I have, to see if that cures any of the problems.

View 4 Replies

Ford Transmission :: 1990 E250 - Shudder When Starting Off From A Stop

I am not the original owner of this 1990 E250 cargo van with a 302 in it. I am trying to troubleshoot this shudder I am having. It only happens when I am just starting off from a stop. Every other place the tranny runs and shifts great. I trying to find a starting point and after reading a bunch in a bunch of different places, I am confused as to the tranny I have or even had.

It has in big bold letters METRIC on the bottom of the pan. It also has Automatic Overdrive and Ford on the bottom of the pan also. It is a 14 bolt pan with the two rear corners of the pan chamfered off. I see now it is DEFINITELY the AOD installed and NOT the AODE. The thing is my steering column is labeled 1 D and OD. That is a 3 spd overdrive to me. What the heck is going on? How can I tell what the tranny was that came out of the van?

When I look under the van at the shift linkage, you can definitely tell the linkage is colored red which to me looks like somebody has been down there playing around. Is it possible to put a AOD into this van with the steering column the way it is? Could this be a reason for my early shudder at starting off from a stop? Once I put my foot in it or get moving at a quicker pace, the shudder goes away. Something is not right with the way this tranny is set up. I am not even sure where to start.

View 11 Replies

Silverado :: 2010 LTZ Rough Idle / Headlight Flicker - RPM Gauge Fluctuating During Rattle

So I recently bought a 2010 Chevy Silverado LTZ with 31,000 miles (5.3l engine). After having the truck a few days, I have noticed a couple of problems ...

1) I have noticed there is a rough idle in the passenger seat while the truck is in drive. Once the truck is started and driven about 5 minutes, once you come to a complete stop in drive (ex. stop light) a rough idle over takes the truck. You can feel this idle a lot more in the passenger seat than in the driver seat. The RPM gauge also fluctuates during the rattle.

2) At night my the headlights flicker randomly, on and off very quickly.

3) In the morning when I start the truck and drive it a bit, I hear a rattle which sounds like it is coming from the front right of the truck. Bumps do not trigger this rattle, which usually only lasts a couple seconds. I usually hear the rattle between 1,000 and 1,200 rpms.

I have taken the truck into the shop 2 times to get these items fixed, and they said they cannot feel a rough idle.

View 1 Replies

Prius (2001-03) :: Starter Battery Resetting Voltage - Car Not Starting?

I think the 12v agm battery is starting to go on our 03 prius. It wouldn't start after 4 days no use but did after 2. What is a healthy resetting voltage (with nothing turned on) for this agm battery as I'll check it with a multimeter? What is considered an unhealthy voltage?

View 1 Replies

Ford - Ranger :: 2000 - Speedometer Quit / Jump When Brake Pedal Pressed?

I have a 2000 Ford Ranger, 5spd with 3.0 v6. The speedometer will jump around or quit about half the time whenever you push the brake pedal or use the turn signals. I've cleaned all the grounds I can find including taking the battery cables off the clamps and cleaning them, and I had to clean all the fuses (inside box and outside box) because most of them were corroded. It still does it. Occasionally, I'll hear a buzzing/crackling noise like electricity arcing when I use the brakes or the turn signals which sounds like it's coming from the left side of the dashboard.

I took off panels and the fuse box, but I don't see any sign of arcing. Also, the noise only occurs when the truck is actually moving, never when it's sitting still. Also, the engine has a slight flutter at an idle. I hooked up a computer, and the O2 sensors were erratically jumping between rich and lean, so I replaced all of them. It says Insufficient EGR flow detected, so I did put a new EGR valve on and cleared the codes, but it still reads the same. And lastly, the computer refuses to finish either of its diagnostic tests. I've tried the Koeo and the koer tests, and neither will complete.

View 2 Replies

Prius (2004-09) :: Jump Starting - 100 Amp Fuse Blown

I experienced some weirdness trying to jump start a friends 2001 Prius and the 100 amp fuse got blown. I read the user manual and am pretty positive that I did not reverse polarity on the auxiliary battery, with the jumper cables. But as soon as I hooked up the cables the headlights and taillights came on, as well as both turn signal lights steady on, and I couldn't turn them off. I checked and checked. The key wasn't in. All the headlight switches were off. I just couldn't figure it out. After trying to let the auxiliary battery charge for a while this way, the car was still totally dead and it was weird and I gave up.

The next day my friend called AAA and they couldn't start it either. But she said they were pretty clueless, refusing to believe at first that the battery was in the trunk, and suspects maybe they reversed the polarity on the cables when they tried to jump it. She didn't see the headlights come on this time (although it was now during the day).

View 8 Replies

Golf/GTI VI :: Temperature Gauge On The Dash Cluster Doesn't Jump

So recently (past few weeks) I've noticed my temperature gauge on the dash cluster doesn't jump up to 190 as it had before. It just sits there when I start the car, and then eventually builds up as I start driving. Reason this concerns me is because I don't remember this ever happening.

View 9 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved