Hyundai - Accent :: 2002 - Idle Roughly After Clutch Replacement
Mar 19, 2012
The problem started when my clutch fluid began leaking a couple of months ago. I first noticed that it would take an unusual amount of effort to shift into gear and, after checking, found the clutch fluid completely gone and I filled it up immediately. Three weeks later, the fluid was gone again, so I took it in to a reputable mechanic, who said I needed my slave cylinder replaced. A week after replacement, I start to notice that my car increasingly had trouble "catching" into gear (my engine was accelerating, but not moving very fast; soft clutch). I thought maybe something went wrong with the slave cylinder repair and took it back to the same place, but the news came back that I needed a new clutch.
At 143,000 miles on the original clutch, I wasn't surprised it was time for a new one. Immediately after picking up my car with the new clutch--and by immediate, I mean right after I pulled out of the mechanic's parking lot--I noticed my car was driving horribly. The engine was idling extremely rough and it felt gritty when pressing the gas pedal during acceleration. I took it back to my mechanic the next morning to explain the problem, but they treated me like I was an idiot, didn't detect anything wrong with my car, and clearly didn't know what I was talking about even though I personally showed them my steering was shaking pretty badly while idling.
A few more days of the rough idle/gritty acceleration and I went back, but they just suggested getting my fuel injection system cleaned. I personally checked to make sure that the wires in my car were connected properly, as well as making sure the hose connecting to the air filter was on there correctly. Today on a whim, I took my car to Autozone to have them check the computer, even though I don't have a check engine light on, and sure enough the only code read was P0302--Cylinder 2 misfire.
My question is, what is the most likely cause of the cylinder 2 misfire (given my car's very recent history) and most importantly, could the mechanic have caused the problem I am experiencing? How should I handle this situation with them from here? I will no longer be using their services after I get this problem sorted out, as I feel like my car did not receive the best service.
View 1 Replies
Advertisement
Been having a fair bit of trouble with my accent, at first my car sometimes would hesitate on acceleration in 1st gear. Now it has a rough idle and the engine just completely cuts out at random. It does however start straight back up. It makes an odd noise whilst idling almost like a misfire from the exhaust. On start up it blows a lot of white smoke. And when you do get driving it is really jerky. It's been serviced every 5000ks. I've changed spark plugs, map sensor and throttle body sensor, put a fuel injector cleaner through and still no improvements. It's been booked into the mechanics for next Tuesday.
View 1 Replies
I'm having continued issues with my mom's POS 2005 Hyundai Accent. It usually runs great cold, but once it's warmed up, it will stall out while driving. This almost always happens when accelerating from a stop. After it stalls, you have to let it set for 30 seconds to a minutes before it will start again. It will also sometimes idle roughly.
I've changed out the TPS and the MAP sensor, the battery, the CPS, the fuel pump, and the spark plugs. I did find that the radiator bypass hose was leaking on to the wiring for the O2 sensor. I fixed that, and the wires appear to be fine. I've sprayed throttle cleaner around the intake and can't find a leak. I scanned the ODB codes and I'm getting a Random misfire, misfire on cylinders 1, 2, 3, and 4, the Throttle Position Sensor and the MAP sensor, both of which have been replaced.
Tonight during my troubleshooting I was trying the wiggle test on the various connectors and got zapped when I was wiggling the coil pack connectors. Is that normal? I'm starting to suspect a wiring or electrical issue, but I'm not sure how to troubleshoot that.
View 28 Replies
Earlier this summer I bought a 2003 Hyundai Accent with 130k miles on it. Recently I have noticed a squeaking/squealing sound coming from underneath the hood. I first noticed it at traffic lights, but I have determined that it occurs whenever the clutch pedal is depressed, and continues until the clutch is released.
My first question is - is this serious? (Is it dangerous, or will it compound significantly if I do nothing?) The clutch still seems to work fine, and I can stop the noise at traffic lights etc... by putting the car into neutral and letting off the clutch.
My second question is, how did I cause this? Coasting with the clutch fully depressed, or too much downshifting?
Background: Recently, I bought a Scan Gauge to provide real-time fuel economy feedback, and began to experiment with different driving styles. I found that I could really boost my fuel economy by coasting down longer hills on the highway (when there were no other cars around). To do this I was pressing the clutch all the way to the floor, figuring it was the same as putting the car into neutral. When my speed began to decline after the hill I'd ease back into 5th. One hill in particular comes into town where there is a light. If the light turned red I would stop coasting and do some quick downshifting as well as breaking. I was pretty aggressive with the downshifting on a few occasions.
Did either the downshifting or the coasting likely contribute to my problem? If coasting was an issue, would coasting in neutral cause a similar problem?
View 2 Replies
Vehicle is an 08 Hyundai Accent 1.6L three door (hatchback) with 20,197 miles. This car was born on Oct. 16, 2007 and purchased in April of 2008. I told the owner to call the dealer and find out about when they should replace the timing belt as I had looked it up at the Gates site and found that it is an interference motor and also these Hyundai have some kind of lengthy warranty. When the tech or whoever she spoke to at the dealership asked about the mileage, they told her that she does not need to worry about the belt for about another five years, were rude and sounded inconvenienced by her calling. This leaves her with a bad taste in her mouth and more importantly, mis-informed.
I get the "Maintenance Log" out of the glove box and upon trying to decipher the timing belt interval, it states that the first course of action is an "inspection" at 30,000 miles or 24 months. How is a timing belt inspected? From what I have seen, a belt can look perfect today and snap tomorrow. But anyway, the next entry for severe service is replacement at 37,500 miles or 30 months which means this belt should have been replaced in October of 2010. Next entry is normal change at 60,000 miles or 48 months which puts us at April of 2012. After this it goes to 75,000 miles or 60 months.
I have already picked up the kit for changing the belt, tensioner, idler, and the two seals. How critical is it to change the spring as that was not included in the kit I got? I'm planning to do this job here in the next couple days as from what I can figure from the above log, It's way over due. I was reading some Hyundai forums and one stated that the 2011 model with the exact same engine calls for the first replacement due at 90,000 miles. How's this possible? Seems like these people (engineers) don't have all their stuff in one bag...
View 7 Replies
I have a 2002 VW Beetle 1.8L Turbo with over 120k miles. Recently it started idly roughly on occasion and had a slight rattling noise but only when stopped. When it was driving, it felt fine. This went on for about a week and then one day about a week ago it started for about 10 seconds and then stalled. Since then it will turn over, but not start. We've checked the starter, fuel pump, fuel pump relay and ignition coils and have replaced the crankshaft sensor (which was what I found on VW sites as saying it often solved problems like mine). The battery is new. Part of what I saw when researching was in addition to what is currently happening other owners had a long term issue with the car bogging down once in awhile at high speeds (50 mph+) for a few seconds and then picking back up again. My car did this as well and that's why I thought the crankshaft sensor may be the issue.
View 3 Replies
The headlight on the driver's side has burned out, should i move the battery in order to get to the bulb?
View 3 Replies
'02 Hyundai Accent, 165K miles... My route to work is six miles of secondary roads and city streets (25-40 mph), followed by 16 miles of interstate highway (65-70 mph), then another nine miles of secondary roads and city streets.
I have noticed only recently (last couple of weeks) that when I get to the end of the interstate leg in either direction, as I wait for the light at the end of the ramp, my oil light will flicker (sometimes very faintly) if I leave my foot on the clutch. If I get into neutral and release the clutch, the light stays off. It will do that at two more stops in rapid succession, but by the time I am at the last traffic light or stop sign of the trip, it has stopped flickering regardless whether the clutch is in or out.
Oil is recently changed and at proper level.
View 13 Replies
2000 Hyundai Accent with 180K. Runs and idles smoothly. When sitting for a few minutes at idle I get a waft of smoke when I accelerate. The car burns minimal ammount of oil and the smoke is not apparent while driving.
View 4 Replies
I have a Hyundai Accent 2002 which has 126k miles on it. Overall the car runs well without any trouble. Recently I am noticing that if I suddenly slow down (like taking an exit from interstate or sudden traffic so that speed reduces to 30 mph from 60 mph or so), the front of the car starts shaking. On a very few occasion I have noticed that the check engine light comes up for a few seconds and disappears. At the same time car looses it's acceleration power. However, as soon as I slow down further (close to stop) everything starts working fine without any issue. What could be going wrong? The car is due for a timing belt replacement around 130k miles .
View 3 Replies
I have a 2002 Hyundai Accent with 116K miles on it. Recently it started to make a squealing noise when I start the car. The sound stays there for about 15-30 seconds and then goes away. Also, while the car is running and I start the AC for the first time the same noise sounds for another 15-30 seconds. I took the car to a local Midas store and they told me to replace two things. Alternator Serpentine Belt and Power Steering Pump V-Belt .Does the parts sound reasonable? I am really novice about car mechanism.
View 7 Replies
Car died at idle on park. Tried to start it back up and was only getting crank. I took it to a local mech and he said my timing belt failed. I paid for the repair and the car still wouldn't start. The shop said the ecu went out. I replaced the cam position sensor and main relay under the dash. Still not getting it to start. I also have a ecu from an 05 accent, would this be plug and play? What else can I do?
View 3 Replies
So I have a 2002 Hyundai Accent 1.5L. My car will drive 1-2 miles then it dies. After I let it sit for about 10 minutes it starts up again. I am getting to the end of what I know to do. I have replaced the ECU, Main relay, most of the sensors, Fuel pump, and fuel filter. When I bring it in to get the codes for it all I get is sensor faults even though I have replaced them. I am going to let it run for a little while and see if I can feel any heat from any relays under the dash. I like this car but not sure what else I can do.
View 4 Replies
On 4/11/11 - we replace the clutch in our son's Nissan Altima. Yesterday - the clutch died as he was getting on the highway. It was towed to the same repair shop. They took a quick look and said it's likely the new clutch is gone. They weren't sure what our son did to it. We're baffled. What could he have done in 6 wks that would totally blow a brand new clutch? At this point - we don't know whether to throw good money after bad.
View 7 Replies
2002 Hyundai Accent with automatic transmission. This problem happens only if I floor the gas gas on the highway (trying to pass somebody or get out of the way in a hurry) or if I apply too much gas after coasting around a sharp turn. My car will then downshift with a jerk and an audible THUNK!. Right now I just avoid those situations and it shifts through all its gears fine, it only happens when I cause a sudden downshift. Transmission fluid level and color fine.
View 1 Replies
I have a 2002 Hyundai Elantra that is exhibiting some strange behavior at idle.It wants to rev from 1500 to 3000 rpm, then back down, over and over again, every two seconds or so. This does not occur when the car is in drive or reverse; it purrs along at a consistent 1200 rpm.It all started with overheating and a water pump change, which was completed and reassembled.Then on startup, we began getting this revving. We double and triple checked the timing belt. We sprayed plenty of carb/choke cleaner in the areas of the vacuum hoses searching for a leak to no avail. Whenever we hookup the OBD code reader, there are no codes.Why does my car want to challenge everyone to a drag race, and what is causing this?
View 8 Replies
During recent cold/ice spell, went to use my rear wiper and heard a pop (there was ice around the wiper base), then the wiper was flipping all over the place. Now I can hear the motor running but the wiper doesn't move. Plus, I can easily move it around by hand - no resistance. Do I have to replace the whole motor or is there possibly a gear or linkage between the motor and arm that stripped or popped away, so that can be fixed? 2002 Hyun Accent.
View 5 Replies
When I start it up it won't idle untill you give it gas to 2500 rpms and slowly let off the pedal to 1000 rpms to keep it running and itll stay running. When you turn it off you have to redo it all over again. The plugs and wires were replaced. It started doing it couple days after the back 3 plugs and wires were replaced. Just got the fuel pressure regulator replaced and it still wont start up without giving it gas.
View 6 Replies
2002 Hyundai Elantra GT 2.0L 140k miles
Symptoms:
- Intermittent rough idle when hot, slight shutter, surges between 700-800rmp
- Intermittent hesitation when accelerating, cylinder 2 misfire when hot and under load
- Misfires in all gears under load, mostly when under 2000rpm
- Code P0302 when scanned, no other codes
- Symptoms appeared suddenly, not gradually over time
What's been changed:
- Replaced spark plugs, little or no improvement. Old plugs looked worn, but generally in good shape with no significant deposits.
- Cleared code and swapped injectors between cylinders 1 and 2, after test drive P0302 code came back, so it seems that the injectors are good. If the injector were bad I would have expected the misfire to change from cylinder 2 to cylinder 1.
Inspection and Testing:
- Ignition System Testing
- Spark plug wires and primary coil are within specification.
- Secondary coil resistance is high on both packs. Could this be causing a problem with just cylinder 2? Is it worth replacing?
Spark Plug Wires: Specification: 5.6 Kohm/meter +- 20%Cylinder 1: 2.49 Kohm (Longest)Cylinder 2: 2.03 KohmCylinder 3: 1.64 KohmCylinder 4:1.36 Kohm (Shortest)
Primary Coil: Specification : 0.58ohms +- 10%Actual: .6 and .6
Secondary Coil: Specification: 12.2 Kohms +- 15%
Actual (Cold): 16.03K for Cylinder 2-3 pack and 15.94K for Cylinder 1-4 pack
Actual (Hot): 18.54K for Cylinder 2-3 pack and 18.44K for Cylinder 1-4 pack
Air/Fuel System Testing:Fuel system seems to check out. I do not believe the problem is fuel related. There are no obvious cracks or leaks on the intake manifold. A good spray of Carb cleaner all around the manifold causes no change in idle. I might try propane later. No obvious vacuum leaks.
Fuel Injector: Specification: 13.1-14.5 ohms
Actual: Cyl 1: 14.9, Cyl 2: 15.3, Cyl 3: 15.3, Cyl 4: 15.7
Compression Testing:Compression is not great, but within specification. Could the slightly lower compression in Cylinders 2 and 3 indicate a head gasket leak between those cylinders? Could this cause a misfire in Cylinder 2?
Dry Compression: Specification: 145-218psi, <15psi between cylinders
Actual: Cyl 1: 165, Cyl 2: 155, Cyl 3: 155, Cyl 4: 160
Oil/Coolant/Tailpipe:
- Oil looks normal, not brown or milky
- Coolant looks normal and is full, no signs of leaking (coolant has not been changed in a very long time, could a coolant flush work?)
- Exhaust looks and smells normal from tailpipe.
Sticking valve? How would I check this? Bad sensor somewhere? Doesn't a bad sensor usually throw a code?
View 4 Replies
I recently replaced my Ford Factory clutch with a new LUK kit, lever, pivot & hydraulics and I have to say it is absolutely perfect. If you are going to take the time to do the clutch, do it all. While we had it apart, I decided to push up my Up-Pipe replacement and do it while the transmission is out. What takes several hours to do is done in 30 mins this way. As we all know when we start in a job, we see other things and say well while it is apart I may as well do this, and do that. I decided to do the U-joints in the rear shaft. I had marked the shafts prior to removal for orientation but my assistant did not mark all 3 U-joint knuckles when he changed the joints and reinstalled the shaft.
I took the truck out for a drive and starting at about 15 MPH all the way to 60 ( I dared no faster) it was making me nauseous. Today I looked into it, marked current locations and started rotating front and rear joint 180 to no avail. I said lets just rotate the center joint and go from there. as I was pulling the carrier i noticed a HUGE but dull yellow arrow on the short shaft. I decided to look at the rear shaft and found a HUGE but dull yellow arrow 180 degs from the front. It looks like it could have been a factory mark. I repressed the center u-joint so the 2 arrows line up and the vibration went away. I can not express the aggravation this could have caused if not for those arrows. Take the time to properly index the drive shafts, it will save you tons of time and agitation.
View 1 Replies
Replaced this gasket that seems to be leaking oil. Looks simple enough, is there anything i should do or know before taking on this job? It's a 2002 Accent GS 1.5L ....
View 8 Replies
