Sebring - Chrysler :: 1999 - Turn Signal / Hazard Flashers Don't Work
Aug 18, 2012
The turn signals/hazard flasher on my 99 Sebring Jxi stopped working a couple of weeks ago. When I use the signal lever or press the hazard flasher switch, you don't hear any click of the flasher relay, and the lights (front and rear, and on the dash) don't light up at all.
So far, I have:
* Checked the fuse
* Replaced the flasher
* Replaced the turn signal switch
* Replaced the flasher AGAIN (mechanic says that if there was a problem with the turn signal switch, it can burn out the flasher)
* Checked the fuse AGAIN, and even replaced it (even though it's the same fuse for the wiper/washer, and that's still working)
I asked my mechanic about it, and he said that a bad ground can also cause problems. The big question is: where do I begin to look?
View 3 Replies
Advertisement
I have a 2003 V10 Excursion with an electrical problem. The right turn, right brake and right hazard light do not work but the flasher makes the clicking noise. When the right turn signal is on, the right front turn signal light works but is at double speed. The right rear light does not work. Same when brake and hazard are applied.
I checked the bulb socket with a multi meter and have no current. I also checked my trailer plug and have all functions work. Fuses were checked also for the brake circuit and were all ok.
View 4 Replies
I have a chevrolet optra 2007 and the hazard lights won't work unless the turn signal (left or right) is switched on at the same time. Turn signals work perfectly fine.
View 7 Replies
Recently, I lost function of brake lights, turn signals, and hazard flashers. All happened at the same time. Some threads discuss flasher relays, short steering column wiring (position of steering wheel), and fuse failures.
I checked #18 fuse and a few others. All had continuity. I assumed my bulbs were all good. My hazard push-pull switch did not feel right. There didn't seem to be engagement. At this point, there was a good chance that the multi-function column switch had failed so I decided to try replacing it. I'm happy to report that this switch was the cause of all the light function failures and now, all is well again.
Removal is done by prying the key lock switch cover off,, removing three 1" Philips head screws that attach the lower column shield to the upper shield. At that point the upper shield can be completely removed. The lower shield was not totally removed because the tilt lever was left on. The switch is attached to the column with two 3/4" Torx 20 fasteners. The upper is easily accessible and the lower fastener can be removed by pulling the lower column shield down so access can be achieved. The two wiring harnesses have a conventional harness lock to depress and the connectors pull outward from the switch. Installation is the reverse of removal, noting the dowel locator and small plastic dowel on the lower shield.
View 1 Replies
The right turn signal on my 1998 Ford Explorer recently stopped working. The flasher was making a horrible buzzing sound when I tried to signal right, but worked fine signaling left.
I just replaced the flasher, which has cleared up the buzzing noise when trying to signal right. The flasher clicks like it's supposed to, but the lights still do not flash.
Here's a summary of the current symptoms:
-Hazard lights work fineFlasher clicks; interior indicators flash; exterior lights flash
-Left right signal indicator works fineFlasher clicks; interior indicators flash; exterior lights flash
-Right turn signal does not work
-Flasher clicks
-Interior indicator stash off; exterior lights stay off
What to check next???
View 4 Replies
My neighbors 02 250 6.8l the turn signal/hazard relay is clicking with key off, sounds exactly like a turn signal when truck is off and switches are not engaged. Here's the weird thing, if you hit the brakes the relay stops clicking, if you engage the turn signal or the hazards the lights on the dash are in time with the relay as it should be, but when the turn signal switch or hazards are turned off the relay keeps clicking except when you hit the brakes. Also the turn signal will work with ignition off, if you pull the relay out the turn signals and hazards are inoperable but the brake lights still work. I swapped in a new relay and same thing...
View 8 Replies
Where the flashers are located? I turned my turn signals on to find the clicking sound, but I couldn't see anything under the dash.
View 9 Replies
I thought I saw someone had converted the reflectors on the front of the side mirrors to turn signal flashers on the 2010-2012 F150. Where I can find that write up?
View 1 Replies
My 2002 Sebring won't start. Here's what happens:
Turn the key in the ignition. Engine makes no noise at all. It's sorta like when the battery died 2 months ago, except this time the power windows and doors work, the headlights and interior lights work, though oddly, the radio doesn't. The radio, FYI, is not the one that came with the car. I bought it back in 2010 after the cassette deck on the original broke and I needed something with an Auxilary connector to connect my Ipod to. I had it professionally installed.
So the car doesn't start. The engine doesn't make any noise. The headlights do come on. The dashboard lights that normally come on when you try to start it up (the check engine light, the airbag light etc., also do not come on at any point. I don't recall any particular clicking sounds when I turn the ignition. I do remember hearing these clicking noises (sort of a quick one time click for each key turn) when the car wouldn't start due to battery/alternator issues two months ago.
So I did a bit of research, and I think it's either the starter solenoid or the ignition switch. Am I far off base?
View 19 Replies
I've blown my turn signal fuse for 3 times until the relay burned out. Now I have had cleaned turn signal switch (with CC) from all of the old stuff in there and replaced hazard switch. But it happens again! After 5 minutes driving, both fuses (7,5 AMP for turn signals and 15 AMP hazard) blown out. I'm afraid there are some shorts in wirings.
I'm looking for the wiring diagrams or any other users experience in this matter... Where shall I start from?
There was a water leakage behind and under drivers seat. I removed trims etc. to lift the carpet to take the Comfort Module for checking as there were some weird thing in overall car electric systems (central locking, saloon lightnings, electric windows and dropping gauges on instrument panel. I found a small amount of water in container, where the module is placed, but on the electric parts weren't any water marks... Also it's impossible to connect to the CCM via vag-com.
View 3 Replies
The turn signals and hazard lights on my nissan sentra are working some times and all of a sudden they stop working. The problem is occuring almost every day. What could be the problem?.
View 4 Replies
I have a 1998 Ford F150. The turn signals do not work nor the hazard flashers. When I trun on the hazard flashers(they do not come on) the turn signals will then work. Checked all fuses both under dash and in the engine compartment. With flashers turned on and using the turn signals, the relays located in engine compartment are working. It appears that the only way for the turn signals to work is to recieve power through the hazards.
View 2 Replies
I have an '05 Chevy Colorado and the front turn signals don't work and no flashers. I've tried replacing bulbs and checked the fuses. Looking for info what would work.
View 3 Replies
My frend has a 89 Sebring that won't start all the dash light come on but turn the key and it doesn't do a thing....
View 8 Replies
New owner of a 2005 Passat GLS TDI.
For some reason, the Hazard switch clicks a few times after using the turn signals (randomly), or while driving it will start clicking for a few seconds. The lights do not flash. it is only the audible sound coming from the hazard switch area.
Where does that sound come from? the hazard switch? Would replacing the switch with a new one fix it?
View 9 Replies
If I make a right turn at anything above a snail's pace, my emergency brake light comes on and it chimes. Had the brakes checked and they are fine for now but since they are original, they will need to be replaced soon. The car has 50,000 miles. Recently had the cam sensor replaced and the dealership checked the car over.
View 6 Replies
My Jetta has had an off-and-on clicky turn signal sound without turn signals or hazard lights actually blinking. I put up with it for a while, but recently it's been more clicky than not. I'm aware this is a common problem. I had already tried the cleaner spray "trick" which made the problem worse if anything. Today, I removed my signal stalk as described here and gave it a cleaning. After re-assembling, the clicky problem didn't go away, and now the high beams are always on (even with the key out of the ignition, and the car isn't running). I temporarily dealt with this by pulling fuses 18 and 19 for high beams. It's an ok short-term workaround. Low beams still work fine.
I'm considering replacing the hazard signal relay, but a while ago I messed up while trying to use ghetto removal keys to pull my radio.
View 4 Replies
1994 Econoline E350. All the other lights work but on the front right the turn signal light flashes but the Hazard lite will not flash. I check for power at the wire at the light and there is none.
View 6 Replies
I just found a nice Prius C for sale with little damage to the front right corner, no frame damage or anything, just some bodywork needed. So, after it was fixed up. I brought the car back and there is weird issue that I have - turn signals and Hazard lights dont work. When I turn it on, i can hear clicks from it, but I dont see lights blinking on the dashboard and my head/tail lights dont blink as well.
View 5 Replies
I have 1999 Ford F-150 xlt and on the passenger side the brake and turn signal don't work but reverse light does. On the driver's side, everything works so I switch bulbs and outlets and it still doesn't work but two of the wires for trailer hook up and cut. I was wondering if that had anything to do with that.
View 2 Replies
2013 f-250 crew cab short box, 6.2 gas with 48k miles. Right rear turn signal does not work...SOMETIMES. I took the brake light assembly off...bulb is good, turned on signal and the bulb will flash so I put it back together then drove a couple miles and then signal quits working again. I can't find any loose/corroded/bad wires at the bulb socket and I can't get the bulb to quit working when I have taillight assembly apart, (trying to replicate failure). There are never any blown fuses either.
View 5 Replies
