I have a problem with my 1998 Chevrolet Blazer. It won't go in reverse, but will go into gear going forward. I don't know whats wrong or what the cause is.
View 2 RepliesWhen I turn the key over to start the vehicle, the clock resets to 1:00, the back latch clicks and the car kind of makes a grinding sound but not like a churn as if it wanted to start. I don't know if it is just a dying battery or if it would be something else but my car will not start at all.
View 1 RepliesI have a 98 chevy blazer that the dash lights and interment cluster (including odometer) only works at night when u turn on the headlights by the switch. And the truck starts sometimes. I placed a piece of tape over the sensor on the dash for the auto lights( this made the dash, interment, odometer work) but now truck will not start. I've been told its the ignition switch.
View 1 RepliesMy trailblazer will not move in reverse , and will barely move forward, i checked transmission fluid hot and it's not even on the dipstick but when it was cold. it was?? Do I add more or what?..
View 9 RepliesI have a 1998 chevy blazer v6 about 127024 miles. My transmission shifts hard out of first gear when i get to 4 gear and it shifts hard. When car warms up really good car shifts find out of first gear but 4th gear still shifts hard. I did change transmission fluid and new filter in it and I check fluid level and it's full.
View 6 RepliesI have a 2011 Chevy Malibu, with a little over 100k miles on it. A couple weeks ago it started acting a little funny when I would shift into reverse after starting it after sitting for a while. I thought it might have been due to temperature as it didn't do it after the car had warmed up or when it was warmer out.
Yesterday it started acting up really bad, will not shift out of first gear, and will not shift into reverse, and the check engine light came on. I was able to get it up to O'Reilly's to get the codes. It came back with 2 separate codes.
P0700 - Transmission Control Module (TCM) Requested MIL IlluminationP0776 - Clutch Pressure Control (PC) Solenoid - Stuck Off
The guy there seemed to think that the second code was probably caused by the first one, and most likely the TCM needs replaced. It makes sense to me, but before I head down this path I want to get some input, as it is a little over $300 for the part.
I just purchased an Automatic 2009 Camry LE with 64k 2weeks ago, and noticed that twice it felt like it was losing power on an incline so I bought the fuel system cleaner to see if that worked (seaform). Tonight I go to park it on a street with a slight incline. As I shift to reverse to line the car up, it rolled forward. It shocked me bc there was a parked car right in front of me. I tried putting it in Drive/Park etc then back in Reverse it still rolled forward. I put my foot on the brake and gas at the same time to try to reverse but not wanting to give it too much gas bc I was scared it might fly forwards into the car in front of me (still rolled forward). Finally I was so close to the car in front of me I gave it a try and it still rolled and bumped the truck in front of me but with enough gas it went into reverse.
View 6 RepliesMy son called me today to pick him up. His 98 S10 would shift into gear but wouldn't go forward or into reverse. New clutch 6 months ago, hoping something simple like low gear oil or worse?
View 1 RepliesI have had my manual 2014 four months now and still can't get used to the fact, that to engage reverse you have to move the stickshift FORWARD into the same spot as first gear. I have had a half dozen near wrecks because of this.
View 5 RepliesWe have a 2001 Santa Fe. Very recently it began hesitating when put in gear going forward or reverse. Once the gas pedal is pressed, there's a delay of up to 2 seconds as RPM climbs, then the vehicle jerks into gear. It seems to run fine otherwise. Mileage is approx 128 k. Maintained very well by the same mechanic until very recently. Internet searches have gotten answers of use fuel additive, install some computer patch, fix an oxygen sensor, change tranny fluid and flush tranny, rebuild tranny.
View 2 RepliesMy cousin has 1999 f-150 v8 automatic. Anytime you take it out of park you get forward gear. Was fine when parked just started happening on startup.
View 1 RepliesEarly 2000 F250
Originally the truck would not go into any forward gear, but had reverse all day long. So I had a rebuild kit ordered (new bushings, seals, frictions, steels, a washer and flat bearing kit, a sprak kit, and the od piston)
After rebuilding it, taking my sweet time double checking everything, it will now go into forward gear but not reverse. So I dropped the pan. The small 3 bolt plate was torqued to spec. When I got to the third bolt in the smaller section of the valve body (upper valve body) I heard a click like maybe a valve returned to its place but I'm not sure. I removed the valve body and accumulator and all the valves were free and had tension. When I had it apart the first time one valve stuck for a split second but I never could get it to stick again.
Finding nothing there I uninstalled the tranny and took the barrel apart all the way down to the L/R piston and could not find anything wrong.
After the build and me running the truck for about 10-20 min there was metal on the magnet (part of the reason I took it all back apart) however I could not find anything worn or chewed up. Could have been the tc I prefilled with 2 quarts in stead of filling all the way.
When I initially rebuilt the 4r100 I took apart the pump to replace the bushing and seal but did not take apart the valves. I've heard the pump is directly related to reverse but I'm not sure. Could something gone wrong in the pump when I took it apart? How would I know? If I new all parts of the reverse system I could then test them.
The gear shift works fine, and we lifted the hood and saw that the mech. arm IS working when we shift. However, the van will not move into any gear. won't go forward, reverse, etc... it acts like it isn't shifting.
i was driving down the highway, and noticed it wasn't accelerating and stepped on the gas.. .and nothing. I stopped the van, put in park, turned it off. Started it again, and put in D and wouldn't go, just engine revved. then put in reverse and same thing... didn't move but engine revved.
I've got a 2003 Accent and my automatic transmission went out, no reverse and the only forward gear is 1st. Was thinking of pulling it and swapping it for a used, but I have been reading on here the many, many automatic transmission problems of the accent and my next thought was to just rebuild it myself. But now I'm thinking more along the of a swap from auto to manual, as I don't want to have to rebuild a transmission that is only going to have to be rebuilt again anyway. As far as stuff like the clutch pedal, linkages, gear shifter, I can get those pretty easily. Does the Accent have a hydraulic clutch?
View 2 RepliesThe entire cooling system has been overhauled; including heater core replaced 3 times, new radiator, new theromostat 2 times, new water pump, new radiator hose. Truck continues to overheat into the red quickly with or without a/c on.
1996 chevy s10 blazer 4x4 4.3 liter (1 owner).
My 2001 F250 5.4 has started to make a screeching sound. It only happens when it is in gear (auto) moving forwards or in reverse, and increases in pitch relative to engine speed rather than road speed, and is much more noticeable under mild to moderate acceleration. Maybe I actually mean transmission input speed?
When simply maintaining road speed, it is almost silent. Anyway, if I drop it into neutral while driving, the sound stops, and starts again when I put it back into gear.
From the drivers seat and with the windows closed, it sounds as though it is coming from the engine bay at steering column height, although this is really tough to gauge while actually looking where I am going. With windows open, it comes from both sides of the vehicle.
1st thought is tranny......
2nd thought is a water pump bearing, although there are no apparent cooling problems or leaks.
3rd thought is the alternator bearing, although there are no charging problems.
I say alternator because I recently changed the serpentine belt and noticed that the alternator made a very faint screech-like sound when spun without the belt on it. The main screech was there before I changed the belt. Maybe it gets really loud under load?
So I'm kinda scratching my bean and wondering what expensive piece of mechanics I'm going to shell out for next. If it's #2 or #3, I can do those myself, but if it's #1.... it likely means more money than I have to spare.
I did wonder about removing the serpentine belt and driving a very short distance (end of the driveway and back) to see if I can remove the pulleys, tensioner or other belt driven parts from the equation. Maybe this is not such a smart idea. I'm somewhat at a loss right now.
Okay I am having a problem with my A/C in my Blazer I've had my compressor replaced finally got all of my leaks fixed and replaced all the visible vacuum hoses and still without by passing my heater core I have no Air Conditioning. It just keeps blowing out hot air. Why my Air Conditioner is working. I really like my blazer but after having invested a little over 600.00 into just getting the A/C up and going with no luck is just getting frustrating. I am considering selling it and getting a truck. I would like to keep it if I can get the A/C up and going but I don't want to have to invest a whole lot more money into it.
View 1 Replies96 chevy blazer overheated did compression test number 3 was low on compression. And number 3 misfire.
View 1 RepliesMy 1992 chevy k1500 blazer full size is having trouble shifting from 1st and 2nd and 2nd to 3rd. I reset the linkage it did fine for a day and now it's doing the same thing but it almost goes into neutral while shifting into some gears. And seems to lack power, the 92 doesn't have cyanoids and the transmission was redone 2 years ago when I got the truck. Could this have anything to do with the fuel filter? I know the transmission isn't bad. The Rpms are shooting up way too high.
View 1 Replies1999 Chevy Blazer, 4.3L V6, 173,447 miles
Working on his 1999 Blazer that he just bought, it has an electrical problem.....the gauges are inop, and the engine wont shut down and the 4X4 wont engage unless the headlight switch is turned on and in some instances the high beams must be on. We have replaced the high beam multi switch, the headlight switch and the ignition module. We suspect that it might be a bad ground or the interior light module.
We just replaced the engine the other day but the problem existed prior to the motor swap.
I have a 97 chevy blazer, that has no headlights. the daytime running lights, dash and marker lights all work but not the headlights or high beams?
View 4 Replies