Celica :: 1990 - Car Loosing Power And Can't Accelerate To High Speed
Oct 11, 2011
I have a 1990 celica hatch automatic with 33x,xxx miles on it. the cars always had problems like it would suddenly turn off or the rev would go high but all of thats been fixed
recently the car started losing power and it cant really accelerate to a high speed and speed past 30 and the car will start to shake a lil as if it was gonna turn off and even if i floor it at high speed it doesn't really go anywhere and if i use overdrive the rpm shoots way higher then usual.
Do i need new engine or is it other problem? my friend said it could be distributor?
View 2 Replies
Advertisement
One morning I went to start my 2000 Accent, 1.5L Auto and the engine couldn't get going. I had road service come look at it and they said the problem was the fuel pump, I then got the car towed home. I changed the fuel pump and everything was working great again. I then changed the fuel filter, air filter, oil filter and flushed/refilled the oil. I used the car very lightly for a few days and had no problems.
Then yesterday I took the car about a 30 min drive, when on a main road my engine begun loosing power and I couldn't accelerate, as if the engine was not getting fuel. I managed to pull over safely and after about 30 mins of not getting anywhere I decided to hit around my fuel tank/pump with my club lock many times and what do you know the car starts and I manage to drive it about 25 mins, I was almost home when the same thing happened. I pulled over, waited, hit the tank and finally drove all the way home.
When I originally changed the fuel pump everything seemed fine, the plastic pump housing and everything attached to it appeared in great condition. So my hunch is that the problem would be where the fuel actually enters the engine block? The way that everything works fine until driving for roughly 25 mins makes me think the problem may be dependent on the temperature of the engine, given that's the main variable that changes?
View 1 Replies
I've noticed when trying to maintain a low speed (25-35mph) the car doesn't really like that... Almost feel like the brake is being slightly pushed on and off, or the car is losing power. It's been most noticeable around curves when coasting but having to give it a bit of gas to maintain speed. Shifting overall doesn't seem bad, so it doesn't feel like a tranny issue. I've also sometimes noticed the opposite. Sometimes when coasting then pushing the brake to slightly slow up it almost feels like the throttle is very slightly being pushed. Not sure if I'm having powertrain issues or just not used to the way this car drives. It just get most annoying when trying to maintain 30mph in city and the car occasionally surges a bit.
(2010 camry xle, i4, 97,000 miles)
View 1 Replies
I just got new parts replaced in my car and I thought it would run way better but it seems to run worse. I took it in to a mechanics shop that I new. I have a 1990 Honda Civic Si Hatchback and before I he replaced new parts it was running nice. At high speeds after a while it would shake a bit and then the Engine light would turn on. He found out it was the O2 sensor. He has fixed other problems I had before and it made it better but this time I don't know what happened. So this time he replaced my timing belt, O2 Sensor, Water Pump, Spark Plugs, Valve cover seals, and just cleaned around the new parts. He said it was very dirty and gross in side my block and other placed. When I got it back from him I drove it around and it felt REALLY sluggish. Its a standard. Normally it would jolt forward because it had a quick acceleration and I learned to control it well but now it has a fixes slow start no matter how hard or far I push down on the gas? Its a lot easier and smoother to change gears because before I would seem my passengers jerk when I changed gears but I did see them do it this time. I have a feeling it's my O2 Sensor. It felt like a sport car before and now it feels like it drives like I'm a old nerves lady.
View 11 Replies
So my aunt's celica just crapped out on her over night. Car was running normal till the morning she was going to work. She started it and had all kinds of problems.
Basically, engine has no power. I live not too far from her (half a mile) and i tried to drive it to my house to work on it, and it was a terrible drive. I had to keep it in first the whole time, with the car barely accelerating.
Car has new spark plugs, new cap rotor and wires, Here is a pic of how the spark plugs look like after 3k miles
I checked timing and it was perfectly aligned, i swapped over a known good dizzy and nothing has changed.
Changed out the ect sensor for a new one, nothing has changed.
Here is a video of how it runs .....
Not sure what that popping is but it sounds like it's coming from inside the intake manifold.
View 11 Replies
Driving on the highway today and when I started to accelerate fast I noticed my check engine light blinking yellow and also noticed loosing boost I think I can only reach maybe 10-12 psi, I am stage 1 revo and also it was 95 degrees out, what it could be, thinking misfiring? so would that mean new coil pack and spark plugs?
View 15 Replies
My f350 6.0 has seem to have lost its power, while I was driving home it would only accelerate at one constant speed, and driving up hill it would not accelerate at all, I also noticed an elevated exhaust temperature.. There are no warning lights or dash lights indicating any problem.....
View 8 Replies
I have a 90 gts celica, which the motor went in it, so i put a 93 5sfe into it. I took the old distributor out of the 90 5sfe and put it into the new motor. I wasn't getting any spark. So i replaced the distributor with a known good one. No spark. replaced the coil and igniter, no spark still.
View 10 Replies
Just acquired a 1990 celica gt at a steal lol and needing some troubleshooting answers. tonight was the first night we really had drove it, but my husband drove it to work which is an hour away and he noticed that when he comes to a stop the oil pressure light comes on. as soon as he starts to go again it goes off. the engine does not make any noises other than the typical 2200 lifter chatter and it does not leak oil.
We plan on doing an oil change so we are not sure if that could just be the issue or if it's something else. we had this issue with a dodge ram we had and it ended up being the oil pressure sending unit. he took the one off the car and it did need some tightening up but however when he put it back on the issue was still there.
We do not believe it's any low compression as the car cranks fine and normal with no rising of the cranking as you would get for a cylinder with low compression. we aren't really sure about the bearings because well that's not one of those things easily tested but the engine doesn't make a noise which I know at times you won't have one.
View 12 Replies
90 GTS - Manual Transmission. 5SFE
I have a vibration that rattles the cab of the car during start up. But if you get out, lift the hood and listen, you cant hear anything. Its only in the cab where you can even tell there's something not right. The motor runs great and seems very smooth to the touch and visually.
The vibration does seem to go down as the car warms up..... Somewhat....You can hear the vibration when driving and go down through slight dips in the road. Kinda like hitting the rumble strips on the side of the hwy.When I release the clutch and under power the vibrations go away. Under deceleration the vibrations are loud.After weeks of research, both TN and the web, I have done all this so far.
Changed Plugs, wires, cap. All four engine mounts were taken out, inspected, and 3 of the 4 were replaced from a donor car. All 4 looked good anyways....
Swapped harmonic balancer/pully from a donor car.
Compression check. 196 200 200 208
Cleaned IAC valve.
Pulled off exhaust manifold and verified CAT isnt broken.
Inspected exhaust from front to back and cant find anything.
Replace timing belt, tensioner bearing and idler bearing while I was in there.
Took both fan belts off and ran car to see if maybe power steering or AC, but car still rattled even though they weren't turning.
Did head gasket while building this car up because it was leaking oil from the front return tube area.
View 4 Replies
Can you glide (meaning no engine engaging) on straight road without a hill without loosing any speed over 40mph? I only can when my speed is dropping. I can drive all electric around town without EV mode, no problem.
Stock Yokohama's, front and rear @ 40psi. will bump them to 44psi. Also oil is higher the high mark, which I am planing to drain.
View 1 Replies
I recently took the engine apart and got the head resurfaced after the head got warped. New thermostat, waterpump, timing belt, serpentine belt, power steering belt, and gaskets for all sorts of stuff. After reassembling the engine everything worked fine. No strange noises. Only problem i am having now is that the cooling fan switches on really late, when the needle is 3/4 of the way towards H, sometimes even a little later. Fan is working as when i disconnect the cooling fan switch(bottom of radiator) and the fan does kick on. ECT was also replaced and nothing seems to work. I did replace the switch and the fans failed to kick on, unfortunately i got it from Autozone.This is a 1990 Celica GTS with the 5SFE 2.2L
View 8 Replies
I have a 1990 GTS with a transplanted 1996 S5HE 2.2 motor. This summer I started getting overheating issues and I believe my water pump is dying.
Here's the symptoms; car will run nice and cool on the freeway doing 70 with the tach turning at 3.5k. As soon as I get off the freeway and RPMs drop the coolant temp will spike almost into the red. Accelerating from the stop will drop the temp but it will hover near the high end of the middle till I get back on the freeway or RPM's go back up.
It does the same thing when climbing hills or when the engine is under load. It did it bad this summer when it was hot out and I was running the AC. Bad enough that it boiled over a couple times. The radiator is brand new and just based on the symptoms I'm thinking water pump.
View 7 Replies
When I put my key in the ignition, I cannot turn the key. I tried putting a small amount of WD40 in the ignition and turning the wheel back and forth while trying to start, but all that did was make my key greasy and my wheel lock up. I've tried getting a new key made from Lowes and Home Depot, but their keys are too wide and will not fit in the keyholes. The only thing I am down to is replacing the ignition switch completely but I'd rather do that as a last resort because my car has had a big problem every week (alternator gone, new wheels, new master cylinder, new rotors/brakes). I haven't explored yet? And also, if it comes down to replacing the ignition switch, how would I do that without being able to turn the key?
View 2 Replies
I just got a 1990 toyota celica and it turns over but dont start. its getting fuel up to the motor. i got it from a friend that gave up on it and he got it from a guy that replaced the 2200 with a 2000 engine. everything looks to be connected but i dont know where to start.
View 1 Replies
A little background on how I got into this situation. Bought a '90 Celica GT for $300, was told it had a blown head gasket. It started and sounded nice, if a little ruff. Upon driving, it would stutter (like a misfire) till 3k rpm's, then that would go away and she purred like a kitten. Ok I thought I can make this girl into a woman. I start my teardown and what I found was: front 5 head bolts were not torqued down, and the only place on the old gasket that looked like blowby was on cylinder 3 towards the front on the engine. I think to myself it was loose headbolts, bang I send the head in to get cleaned, buy the gasket kit and go about cleaning the various other parts.
I was cleaning the blocks mating suface, and discovered a small surface crack. It goes from one water jacket port to the headbolt hole and to the other water jacket port.
The headbolt hole shown is the 4th(from timing belt) on the back of the block. The loose headbolts were on the front.
The crack does NOT go down the side of the bolt hole, or the water jacket ports. I am just really afraid this means a new block. The parts I can return if all else fails, but Im down the tube on the money spent on the car and head cleaning.
View 9 Replies
1990 Celica GT ... I will be completely replacing the transmission, and the flywheel while adding a new stage 2 clutch kit. Also replacing the shocks all around.
Okay now to the problem, I don't know exactly where or what fluid or fluids it is yet. it seems to be leaking oil from the oil pan drain bolt also it seems to be leaking coolant too from somewhere behind the oil catch pan area. I did not change the water pump when the timing belt snapped but it looks like some water corrosion on the pump itself. are these common problems and what will solve these leaks?
View 5 Replies
My Celica is running great, I drove about 30 miles and the car started hesitating to run, I was in heavy traffic, I could hear rattling sounds which appeared as though they were coming from the heater. I stopped at a stop light and I could tell something was burning out. I have lots of power, car is very fast. I went to the next stop light and the car died, it started and I went to the next stop light with plenty of speed and the car died and would not start again. I tried starting the car for 3 hours, no fire from the coil.
I have no spark out of the coil. I am confident the coil is good. I have 2 coils. I went to the salvage lot and purchased an "igniter" (ignition module). I installed it on my Celica, still no fire out of the coil. I have a relay under the glove box that clicks when I crank over the engine. The engine cranks over very well for over 3 hours. I have an after market alarm. Why do I not have spark out of my coil?
View 1 Replies
I have a 1990 Toyota Celica, and I've been having trouble with it not starting after driving. There are no symptoms when the car is running, aside from a very slight rough idle. The car starts fine after sitting for 3-4 hours, but for short trips where it's off for under 1-2 hours, it cranks but will not start. The cranking also seems weak unless I floor the gas while trying to start, and sometimes it will eventually start if I hold the gas while cranking. It always starts at the beginning of the day.
This leads me to believe I'm dealing with a flooded engine, but I'm not sure how to diagnose why. I thought it might be leaky fuel injectors, but wouldn't that cause symptoms when running?
View 7 Replies
I have a 90 celica. I start it up and it idles fast until it warms up. then it runs great until i turn it off. then it will not restart! i went to the gas pump. it would not start after i pumped gas. it turns over but wont start. the next day it starts up fine. it does this all of the time. when it wont start there is no spark coming from the coil except when you let up on the keyl it sparks once.
View 5 Replies
I have a 90 celica gts. when it drove, it would violently shudder taking off in first gear. the front motor mount was shot so i was hoping that was the problem. well right after i fixed it, the starter went so i had to compression start it, and the shuddering was still there, and i was about to shift to second when it revved up popped outta gear and didn't go anywhere. it wouldn't go into any gear.
I can go through all the gears without the clutch in. the guy i got the car from said the clutch was new. now i'm not sure if hes just lying or if the guy who put it in didn't know what he was doing. could this be a bad throughout bearing? or the trans? if its the trans i'm scrapping it, also the shiftier is REALLY loose. and before the clutch went it would make weird whirring noises in 1st.
View 5 Replies
