I have a 2000 F-150 4x4 and the four wheel drive isn't working properly. It does work,but to get it to engage I had to drive in reverse for a couple feet then it locked it and everything was fine,pretty sure that isn't normal. What could be wrong with it? As soon as I turn the lights up on the dash,but the front tires don't spin.
View 1 RepliesMy selector switch does not light up when engaging four wheel drive on my 98 f150,could this be my GEM module gone bad ?
View 6 RepliesMy 4 wheel drive is not engaging on a 2001 F150. The indicator lites on the dash illuminate to suggest that the truck is in 4 wheel drive but sigh...it stays in 2 wheel drive. No gross sounds and the indicator lights are not flashing. Could this be a fuse or a relay issue of some sort. What else should I try?
View 3 RepliesI have a 2000 ford f-150 4 wheel drive that will not disengage, I am down here in south fla where and don't put it in 4 wheel drive much, but yesterday I put in 4 wheel drive and I heard the click click and it engaged I put it in drive and drove it about 5-10 miles parked it and turned the switch to 2 wheel high and got out , got back in the truck turn her back on and the 4 by 4 lamp came one went off then came back on and stayed on and it still in 4 wheel drive and wont disengage.
View 4 RepliesI just noticed the 4 wheel drive on my 2000 Chevy S10 doesn't seem to be engaging. The traction doesn't get any better turning it on and the other day I got stuck on a hill and the back wheels weren't spinning. What I can check or look at to fix it?
View 1 RepliesI just got a 99 Ford f150 with the 4.6. I am having problems getting the four wheel drive to engage. I turn the on the dash and the lights come on for four high and for four low. I have a 00 four by four and it works fine, so I know how to work it. In the 99 I can hear the transfer case engaging and everything clicks just fine just like it's going into fourwheel drive, but the front end is not pulling. The front drive shaft is turning but still the front end is not engaged. What the problem may be?
View 4 RepliesI have a 2000 f150 lariat 5.4L 4x4 and when i start my truck up when it is usually below 40 my truck will idle around 300rpm and shake. It also makes popping noises in the exhaust. I am getting codes PO171 and 174 (running too lean in both banks) I have replaced my IAC, plugs, pcv valve, air temp sensor and MAF sensor and 02 sensors and nothing has changed. I have tried looking for for vacuum leaks using carb cleaner and starting fluid but i nothing has came up. I took it in to a mechanic and he suggested a bad intake manifold but i searched for a leak and found nothing.
View 14 RepliesI have read through the folders and many websites on 4x4 problems. My problem has to deal with my four wheel drive not wanting to engage. It has nothing to do with the front end or solenoids. When I put it into 4x4, hi or low it will not send any power to my transfer case motor. It wont even illuminate any lights on the selector switch. I have checked all fuses and replaced any relays that have to do with the 4x4. Where I should go with this?
View 7 RepliesI have a 2005 F-150 with ESOF. When I turn the switch to 4x4 or 4low the lights on the dash will turn on but the front tires will not turn. I checked all the fuses and they were good. I'm not very familiar with this 4x4 system, what the issue is or on how to fix it?
View 3 RepliesI have a 1997 f150 4x4. When I put to 4 wheel drive on all I hear is grinding, but I'm pretty sure it works...
View 4 RepliesLooking for the vacuum diagrams for the four wheel drive, where I can find them?
View 10 RepliesWell I was trying out my four wheel drive today and it worked fine until I went to turn off switch, it would not cut off it is a 98 F150 switch is located on dash. It is stuck in four wheel high!
View 3 RepliesCan't drive the truck. Went through the how to fix 4x4 and no go. How to kick it out of four wheel dive?
View 6 RepliesI have a 1998 F-150 and when shifting into 4 wheel drive (manual floor mount shifter) the drive shaft from the transfer case turns but the wheels do not engage.
Looking for a diagram of how the axle works?
My 2011 F350 is not engaging 4wheel drive from the dash switch. When I turn it to either hi or lo it says "shift in process" but no 4 WD. It will engage manually from the hub lock, no problem. I know very little about 4wheel drive but am otherwise mechanically knowledgeable.
View 5 Repliest's a '00 extended cab swb 4.6L with 4r70w trans. I have a Hotchkis TVS 2/4 kit on it. It's been lowered 3 years now and I've never had any real issue. But I started noticing a small vibration through the floor so I took my driveshaft out to be balanced and new U joints installed. Ever since then I've had an audible "hum" from the rear whenever I go over 75mph. It only does this under load (hill, etc) and I don't hear anything until then. The driveline shop told me it was my pinion angle and I've tried shims with only slight improvement. I'll replace the driveshaft after I do a motor and trans swap down the line, but it's out of the budget for now.
View 2 RepliesMy father's 2000 F150 5.4L has developed an issue. But the issue only surfaces in it's last gear. As it shifts into overdrive it begins to miss and hesitate and bog. If you disable overdrive you never feel it.
I'm thinking an exhaust restriction. There are no trouble codes, no check engine light. I notice that the note of his exhaust changes as the vehicle warms up, sounds like it's being smothered. And the flow out of the pipe lessens.
My only issue is whether the EGR is causing it or the converters. Haven't seen them go bright red yet, but this has been going on for a good while.
I wanted to get a few opinions before I tear into it today. I'll do a vacuum test on the EGR valve and rescan the codes but don't wanna drive it and heat up the exhaust when i gotta disassemble it.
I have a 2000 Ford F150 XLT 4X2 that has a "clunking/squeaking" noise in the steering wheel, intermittent happens driving straight down the road, hitting bumps, breaking. It is very annoying! changed out lower ball joints tightened wheel bearings, greased idler/pitman arm thinking that was the problem and it became worse. Had someone look at it and stated that the steering shaft was welded?!?! Why would the steering shaft be welded what am I looking at in replacing it (cost for parts and labor time) and are there any other additional parts that will have to be replaced as well?
View 1 RepliesOk, the swap is all done and I have an engine in the truck that has compression in more than (7) cylinders.
2002, 7.3, 4wd - ~120k miles on trans. Fresh fluid (Mercon V).
Put the gear selector in reverse and it goes right into gear with the normal tug and functions as it should. Put it in low gear and it also appears to work fine. But, when selecting '2' or 'drive' it feels almost like its engaging 2 gears at once?? There is limited forward motion and it feels like the brakes are on. I have not driven further than the driveway yet, but I have a long driveway...
The OD light does not come on. I am not getting any codes from AE, but I really don't know how to use it for transmission stuff (I've been using a different scan tool that I no longer have).
We have not put the bed on the truck, so no tail lights - but 3rd brake light has new bulbs and was working (didn't check this AM though... )
I have a couple other codes, CEL, 'check gauges' and no tach. Gonna start another thread for those issues, I'll put a link here in case its related.
Purchased 2000 F150 (224000 miles) about a year go cheap for knock around truck. Only gets driven about twice week (20 miles most). Has been running great until recently. Got in the other day went about a mile and notice really strong vibration in steering wheel and dash. First thought about something to do with alignment etc. After a little experimentation realized it was the motor. When you get to around 40 mph and try to hold the speed constant it starts shaking (I believe the motor is missing). If you mash the gas and accelerate it stops. As soon as you try to hold constant speed again it starts again. I can run it up to say 45 and let off the gas and the shaking stops. Once it was driven like this for about 5 miles or so, when I come to stop sign it idles rough. If it is put in neutral runs smoother. Could the fuel filter be clogging up? I did try some additive to see if it would clean it out, no luck. Now the check engine soon lite came on. Fuel Filter, Plugs?
View 5 RepliesI am having a problem with my 1998 F150 4x4. The 4WD is not engaging. It is a manual shift. I have checked the transfer case by turning the drive shaft in 2WD it is free. When I shift into 4WD it is does not spin freely. So I believe that is OK. I have checked the vaccum diaphram. It will move the piston when I attach a hose and pull vacuum on the inboard hose barb. So I believe the diaphram it self is OK. I am not sure if the hoses and selenoids are OK. They look fine. However there is a constant vacuum on the inboard hose line (red/pink color) wether I am in 4WD or not. Is this OK? How can I check the selenoids. If all this is OK, the next thing I believ it could be is the shift fork in the differential. Is that a difficult job? Do you need to pull the whole axle out to replace it?
View 14 Replies