Ford Ranger / B-Series :: 1999 - Hesitates To Start And Won't Run In Morning?
Aug 20, 2013
I have a 1999 Ford Ranger and every morning when I go out to start it, it really hesitates and doesn't want to run for a few minutes. once it's going it's fine I can shut it right off and it starts fine, and I can leave it all day from 9am to 6pm and start it again at 6pm and it doesn't hesitate, it fires right up.. it seems like it only happens over night..
When I hooked the code reader up, I get codes P0171 (too lean bank one) & P0174 (too lean bank two)
I also get for the I/M readiness status, that the
EVAP - NOT RDY,
O2S - NOT RDY,
HO2S - NOT RDY
Just want to say also that the shop I had put 2 oxygen sensors in not long ago.=
View 14 Replies
Advertisement
ok so let me start by saying, my name is Tim, I own a 1999 Ford Ranger 6 cyl, 3.0L truck, I bought it brand new in 1999 and drove it for a few years and then took it off the road for 3-4 years then last year I went to put it back on the road and I couldn't get it running.
I took it to the dealer and they replaced a key switch module. since then the ranger seems to lack power. It also idles erratically when you first start it in the morning too.
not sure whats going on here but the engine light is on,
I get codes P0171 & P0174 (too lean bank 1 and too lean bank 2)
I would also like to note that I have replaced the fuel pump, fuel filter, transmission filter, MAF sensor, IAT sensor, PCV valve, EGR valve, TPS sensor, idle control solenoid, fuel pressure regulator & new plugs. I have also checked for vacuum leaks with no avail.
View 6 Replies
Mine has a strange issue. 1990 xlt 2.9L manual 4x4. When first start of the day, after start I push accelerator and it has a hesitation like not getting fuel. Where start?
View 1 Replies
Went to start my 99 F250 SD this morning and I got a series of 5 warning beeps. Kept repeating this for 5-6 times? What's up with that?
View 3 Replies
Having a slight issue with my ranger. So I bought this truck out of a junkyard about a month ago, its a 94 4x4 with a 4.0 and a five speed. When I bought the truck the motor was blown so a few weeks ago i replaced it with a 4.0 from an aerostar van I had laying around. Right after I changed it the truck was running good with no issues, until a few days ago going to work the truck started hesitating going up a hill. Now the truck does it all the time, sitting at idle the truck runs smooth as silk, at half throttle it does it the worst but when you mash the peddle to the floor it clears up and runs good.
So far I've replaced the plugs, wires, coil pack, mass air sensor, throttle position sensor, and the fuel pressure regulator to try and fix it but nothing has worked. I've checked the fuel pressure it has 30 at idle and 40 with the vacuum hose pulled off of the regulator, I even taped the gauge to the windshield and went for a ride and there was no drop in pressure when it started acting up. a few other things i have done were plugged all the vacuum ports to rule out a leak, reset the computer and checked for codes. the only code that came up was 522. So I think my next step is going to be buy new oxygen sensors ? But my question is wouldn't the check engine light come on if it was an oxygen sensor ?
View 8 Replies
Problem: engine surging/hesitation, from idle to highway speeds. It will start and run fine, just hesitates/surges when gas is applied.
Before I pulled the codes, I tried seafoam in the gas tank, cleaned MAF sensor, cleaned throttle body, checked air filter, changed fuel filter, pulled/cleaned plugs, nothing worked.
Then today I finally used a scanner and pulled codes (my CEL doesn't work) and I got 157 and 158 MAF sensor fault, high and low voltage. I am reading about 6v on the C and D terminals of the MAF, I know that is much higher than normal, but what does that tell me? Why both high and low voltage readings? Just a bad sensor, or wherever that voltage comes from, ECM?
I also pulled 189 HEGO H02S sensor fault, unable to switch/lean during part throttle. What does that mean, just a bad O2 sensor?
Last I pulled a 542, fuel pump secondary circuit fault. Does that mean the fuel pump is bad or going bad?
More importantly, what should I troubleshoot first, would any of these codes cause my problem?
View 3 Replies
02 ranger 4.0 v6 auto has 110000 miles on it. at highway speeds 65-70mph feels like it strugles to shift, truck will shake and bounce some. when this happens rpm's jump from about 2200 to 3000-3200 after a little bouncing rpms drop to normal. issue seems to be the worst going up hill but will happen every time i hit 65-70. Also the truck will not bounce or shake with the OD turned off and seems to run fine this way.
tranny fluid/ filter just replaced with no change. new plugs and wires
View 3 Replies
1997 2.3 5 Speed. My poor truck is having a hard time shifting into gears. I have bled the master off the truck with the correct method, bled it on the truck with the hose on the slave method while pushing the pedal and multiple times with no bubbles coming out at all, no leaks, etc.
Here's the breakdown -
- Clutch, slave cylinder and shifter bushings replaced about 3 years ago (everything has less than 7000 miles on it)
- While driving and pushing in the clutch, it clearly disengages, although quite a ways down.
- Only shifts hard while running. If I sit with it off with the clutch in, I can shift through all the gears with no effort whatsoever. At times while driving, it gets so hard to shift that it may become dangerous.
- Only things I haven't replaced are the master cylinder and the flywheel.
Should I just assume a bad master and just replace it? It's the original with 188,200 miles on it.
Forgot to mention there are times that when I am at a standstill trying to go into reverse, it grinds like the transmission is still engaged.
View 4 Replies
Ok, went out last night to go over to a buddies place to watch some football. Tried to start my truck but all that happened is that it would turn over, but not start. Had plenty of juice in the battery, and 1/2 tank of gas. It acted like it wanted to start, but nothing doing - just keeps cranking and cranking. Its even more frustrating because I was driving it around most of the day before this happened.
Here's the dillema: Its been doing this for the past two months now on and off. Once I fix something, it runs for about a month, and then it starts doing this again, without any warning signs (i.e. multiple cranks before a start, stalling, hesitation on accel., etc.). At this point I'm clueless. I've replaced the fuel filter, fuel pump, and air filter, but the problem has resurfaced again.
An interesting thing to note is that the only ways I'm able to get it started when it starts doing this is to remove the electrical connection from the intertia switch, and crank the engine a few times to relieve the fuel system pressure. After reconnecting the inertia switch, the truck starts instantly.
So whats the deal? Why this would work, and why suddenly the thing would not start after weeks and weeks of driving flawlessly? Is it possible that my system is either too pressurized or losing pressure somehow, and that is how it be able to start? A buddy suggested it might be injectors, but I'm not so sure, because there is no hesitation on accel or performance loss, or even a rough idle.
View 14 Replies
My 1999 Ranger that I bought used has been serving me well. However, two days ago I went to visit a friend and when I tried to start the truck to go home, the engine cranked but would not fire. I assumed that perhaps I had flooded the engine, so I walked home. I went back an hour later and the truck started up immediately. Then, yesterday, the truck would not fire at all. I towed it to AutoZone to check for error codes, but none were found. I put my inductive timing light on a plug wire and found that there was no spark.
In one instance of cranking, the timing light blinked and the engine tried to fire, but then nothing. The AutoZone man suggested changing the crankshaft and camshaft sensors. I haven't done that yet, but that is my next plan. Can the Ford dealer find error codes that tell what is preventing an engine from starting that AutoZone can't see? For sure there is no spark, but maybe there is no fuel either since I don't smell gas after much cranking. Could it be the inertia switch cutting off both fuel and spark?
View 14 Replies
1999 mazda B4000 4WD 178000 miles 5 speed manual, I've been having a crank no start problem but after a few tries it would start, a week or so ago it was really cold (23) it wouldn't start so I opened the air box and shot it with starting fluid it took about 5 long sprays but it started.
It ran up op 3200 rpms and won't go back down, took it to my shade tree mech. he hooked it up to the diagnose thing it showed no codes, he poured water over the motor it different places and toward the back it idled down for a second so he says "blown intake gasket' so we replace upper and lower and sure enough we could see where there was a bad spot on the upper and a cleaner spot on the port.
That was not the problem it still idles at 3200, I mean wide open screaming, could the starting fluid have done something? Now he says "blown head gasket" I never had any idle problems before matter a fact besides the hard starting problem that started it was running just fine, what happened?
View 8 Replies
My manual 5 speed 99' 2WD 2.5L Ranger is starting to have some small problems here and there. My main concern is when I start the vehicle sometimes, there is no idle. The vehicle will turn over and if I do not hold the gas pedal down it will die immediately after about 2 seconds.
If I hold the gas down so the RPM's stay up (Around 700 RPM's or so, something just a little above 0 to keep it from dying) after about a minute, sometimes few minutes the idle will kick in and I do not need to hold my foot on the gas pedal to keep the truck from dying.
This is about all I know from the problem besides that it does not matter how long my truck is sitting. For example, my truck was sitting for 5 days and I came home and started it up just fine, but after I drove it a few minutes later and stopped driving, when I went to drive it about an hour later the symptoms came back again.
Also, My brakes are acting a little funny. I went through when I first got the vehicle and bled the brakes, took the front rotors in to auto zone or another shop and had them fixed up, and new brake pads. Sometimes when I first start driving the brakes are extremely sensitive, to the point where I apply a little bit of pressure and my truck will start skidding. This goes away after driving for a little bit though.
View 1 Replies
My 1999 4.0L v6 Ranger (auto trans) is having some issues. Recently the fuel pump won't turn on as normal when I turn my key. I have to turn the ignition on and off 10-20 times before I hear the pump kick on and I can start it. I already checked the relay and fuel pump shut-off switch. Neither was the bad.
View 10 Replies
My 99 b2500 4 cly shut off on the road this morning and now will not start. She'll turn over just fine but no sputtering or almost-starting. The engine light isn't on when i try to crank it. Any deductive checklist so i can start narrowing down the problem?
View 14 Replies
I am working with a friend on his 99 Ranger with a 4.0 . When first started it will idle rough and hesitate for the first 300 feet or so, and then clear up and run smooth the rest of the day. If he lets it set for 6 or more hours it will repeat the problem. He has taken it to a local Ford dealer and they have replaced spark plugs, plug wires, coil pack, cleaned the throttle body, checked the air idle motor and passage.
He has had it to the dealer 3 times and their latest plan is to pull the heads @ a cost of 1500.00 to start. Since it runs well, no coolant in oil or oil in coolant nor loss of either fluid, I couldn't figure why they want to pull the heads.
To date it has not thrown a code, I ran it on a New Generation Star tester and cannot find a code. The truck runs great after the first intial start up and does not give any signs of cutting out or lack of power. My guess is it is losing fuel pressure overnight and is taking a while to reprime. Original fuel pump and 160K miles. Will do a fuel pressure test this weekend.
View 1 Replies
1999 XTL 4.0 auto, was doing fine, replaced Interior light bulb, now wont crank over!!! i suspect the anti theft system... how do i fix or ByPass the security system, i can start the truck by Manually engaging the starter Relay under the hood.
View 1 Replies
In the last 2 weeks my 98 Honda Accord has started to hesitate when you start it up in the morning (or the first time for the day). It only hesitates for 2-3 seconds and catches and starts up fine the rest of the day. I know it's not the battery the battery is less than 2 years old and the battery plugs have been replaced recently as well. There is no check engine light flashing or anything saying there is a problem. What it might be? I can clarify that it isn't making the noise you'd associate with the battery being dead (trust me, I've been in the car with a dead battery and will never forget it!).
View 16 Replies
2000 ranger auto 3.0 wife said that she had problems starting the truck
She had wiggle the shifter to get it to start. Have not looked at it yet but i am think the newtrl safety Switch.
View 3 Replies
I have 1994 ranger 2.3 2wd will not start when key is turned to start position - when clutch is depressed there is a click from fender mounted solenoid but it never cranks motor or starter--I need wiring diagram to trace origin of wire on starter solenoid because it does not have 12volts on it--when I jumper 12v on it and have it in neutral it starts up and runs but no voltage and no start with key....
View 2 Replies
Replaced cups 3ish years ago
Replaced IPR (non- Motorcraft) and ICP last year
New (not remans) PIS Stage 1 injectors with Hydra Flash October
Truck has been running and starting (down to 19 degrees) like a dream since the new injectors. After the last fill up the truck has been harder to start in the morning and if I don't let it warm up till at least until the needle moves it will stall and be difficult to start. Once started and up to temp it runs just fine but will definitely take aa few extra turns to get started whether cold or hot.
There is CEL, I don't smell or see any diesel in the coolant, oil looks good and the diesel in the filter is kind of a clear blue? The way it acts when it stalls is kind of like when the IPR went bad the first time... kind of. The few times I was able to get my phone connected fast enough I saw and IPR duty cycle in the 90s flash and a HPOP pressure of 1500 or so flash all while the truck is barely hanging on to an idle.
View 12 Replies
Got a 2002 7.3 F-350 with 300,000 miles and for the last couple of years I've been getting blue smoke on cold morning start ups and its been gradually getting worse, it clears up after about 30 seconds and all is normal,No loss of performance, Oil consumption is minor, however I hate a vehicle that blue smokes, I'm guessing my issue is valve seals are worn, I was wondering if it is possible to replace the seals while the heads are on the engine? and was also wondering how much time it would take to fix? as i would have to have it professionally done. I know its hard to guess a time frame and everyone is different. Sounds like textbook valve seals to me but is there anything else I should check first?
View 14 Replies
