Ford Super Duty (1999-2016) :: 2001 F350 - Rear Axle Code Is Missing
Apr 23, 2013
I'm trying to find to rear axle ratio on my 2001 F-350 dually and the axle code seems to be missing.
View 12 Replies
Apr 23, 2013
Advertisement
Ford Super Duty (1999-2016) :: 2008 F350 - Sensor On Rear Axle?
What exactly does the sensor on the rear axle do? 08' f350. I know it's a speed sensor of some sort, but what does it do or control exactly.
View 3 RepliesFord Super Duty (1999-2016) :: 2004 F350 - Huge Rear Axle Fluid Leak
Put new backing plates, parking brake shoes, springs, etc on my 2004 F350 DRW 4x4. Replaced the inner hub seals and axle o-ring. Filled with Ford Rear end lube and went for a test drive. All was well. Went out last night to take her out again and I've got diff lube running out of both sides on the inside of the rims. Did Ford sell me the wrong seals? Could I have installed the seals wrong? Ford seal part number is 4C3Z1S177A. Axle is a Dana 80, confirmed by reading the tag on the diff.
View 2 RepliesFord Super Duty (1999-2016) :: 2015 F350 - Rear Axle Pinion Seal Leak
I was looking underneath the truck yesterday and saw that the rear end pinion seal was leaking. Looked like it had been for a while. Truck has 35,850 miles on it. Unscrewed the fill plug and a lot of pressure is released. So I'm assuming the breather is clogged somewhere along the line. I have an appointment at the dealer on Friday to see whats wrong. What is supposed to be at the end of the breather tube? Mine has a barbed 45ish degree fitting on the end of it. Its a SRW by the way.
View 5 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Extreme Uneven Wear On Rear Pads
Have a 2001 F350 7.3 4X4 with single wheels in rear. Started hearing brakes noise and decided to change both front and rear pads. Front had almost half the pads left. Rear on drivers side had about half the pads left. The passenger side metal to metal on the inboard pad and about half the pad on the outboard side. The slides on the caliper were a little sluggish but moved freely. Don't think there is enough to have them turned so will have to replace the rotors. Why this would happen. Could the caliper get stuck? It was easy enough to compress with a C clamp.
View 3 RepliesFord Super Duty (1999-2016) :: F350 Missing At High RPMs
I have a miss at high rpms.. I pulled this engine, manual trans, and 4x4 axle and put them in my F350 Majestic motorhome. 156,000 miles on the engine. Slightly dusted engine with good compression 375-400 (cranking and corrected for altitude). Has a little bit of a long start.
No smoke on start up unless 10 degrees or colder
No smoke when pulling either.
Glowplugs ...Good
GPR... Good
Checked resistance from IDM to injectors ...Good
History of some ether for starting before I got my hands on it. I have AE with the ford enhancement. But I am new to working on a powerstroke and new to AE.
ICP ...new
CPS...new
Oil ....new
EBP...new
Installed a pressure gauge to the drivers side upper port on my fuel bowl:
60 psi at idle
55 psi at WOT 2500-3000 rpms under a load
HPOP stabilized pressure is 2750 @ 40% duty cycle
Truck still misses (semi-intermittently) at higher rpm with a load.
Rechecked codes KOEO: None present
I visually inspected valve movement while running (idle). Did the buzz test when cold.... All injectors sounded the same when tested individually.
Did a cct when not completely warm:
P0266
p0272
Repeated the test at normal operating temperature:
P0266
Torque values on rocker arms bolts and injector holds are good. Fuel quality isn't an issue since this problem has remained for 5 tanks of fuel. What I should do next?
Ford Super Duty (1999-2016) :: 1995 F350 - Cylinder 2 Missing After Warmed Up
1995 7.3L f350 400k mi developed 1poss 2 cyl miss does not change after warm up and will die after 10 min .
View 1 RepliesFord Super Duty (1999-2016) :: 2015 F350 - Electric Locking Axle Swap
Putting in a locking axle to replace there non locking axle? Have a 2015 f350. And found a electric locking for a great price. Can this swap be done?
View 14 RepliesFord Super Duty (1999-2016) :: 2000 F350 - Grinding From Front Axle When In Gear / Under Load
The issue is with my 2000 F350 crew longbed V10. Other than a BTS trans put in a little over a year ago, and FoMoCo motorsports headers, the whole truck is bone stock. Oh, it has that fantastic auto-hub thing with the fake locking hubs and the little switch on the dash (I'd love to convert it to a manual shifter...?). 174k on chassis, so things need to be done, 40k on engine, 3k on BTS 4r100.
Yesterday I was running around town, made a stop, and when I started moving again got a loud grinding from the front axle. Thought maybe I'd picked up a rock in a caliper or something, so I jumped out and checked everything, no joy. Moved forward, there it is again. No vibration, but loud enough (or telegraphing enough) to hear clearly in the cab. Let the truck roll forward, popped in to neutral, noise fades away. Back in to drive, there it is. So, now I know it's trans/t-case/driveshaft/related. I recently put new vacuum lines in, checked all the connections, and pulled, cleaned and lubed the hubs.
And since the trans is a nearly new BTS that is working just find, I'm narrowing the search to the hubs, drive shaft, t-case.
Get home (noise abates above 30mph, or everything else drowns it out), crawl under, and find the front driveshaft is locked. Ok, stuck hub? Pull out both the fake locking hubs, and now the shaft turns. I can turn each front axle by hand at the u-joint, and I kinda hear a faint grinding on the right side (will bad needles make noise only under a load from the trans and not coasting in neutral?), and when I swing the drive shaft around the left axle moves, right doesn't, etc etc.
I'm going to pull the drive shaft today and check the U joints, and drive a bit to see if the noise is still there, but I am thinking I might have some bad needles on the pax side axle...
Ford Super Duty (1999-2016) :: 2000 - Blank Axle Code?
I plan to be buying a 2000 F250 V10 in a couple of hours.
I had my boss run by and take a picture of the door tag so I could determine the axle code. What he sent me was this:
Other than giving me the knowledge of how bad of a photographer he is, it doesn't tell me much else. The axle code area is blank, what gives? Am I just going to have to crawl under the truck when I get there after work?
Ford Super Duty (1999-2016) :: 2005 F350 - Changing Ball Joints - Can't Remove Axle Out Of Diff?
2005 Ford 350. I want to change the ball joints on the front axel and I cant remove the axle out of dif. to remove the ball joint housing. I have been prying and pulling and it just moves out a 1/4 inch or so .They tell me there is no ring to remove in dif before you can pull it out but why this trouble?
View 4 RepliesFord Super Duty (1999-2016) :: 2004 FX4 - Rear Axle Locks Up?
It seems that every time I put the truck into 4 low, the rear axle locks up. When turning, one tire skips no difference which way I turn. When doing this, I do not have the front hubs locked. Also noticed that when turning in 2wd one tire will spin w/o other locking up. I have spun the tire enough for the L/S to catch, but hasn't. I have heard that the locker was not available until years later. Is this true?
View 11 RepliesFord Super Duty (1999-2016) :: 2008 F350 Rattles On Rough Roads / Front Outer Axle Rebuild
I am getting ready to put new axle shaft u-joints in my 2008 F350 (they are shot, they actually rattle on my rough roads). While I am at it I figure I will grease the front wheel brg cartridge, replace the needle brg that is inside the cartridge. I am also afraid I will the axle shaft vacuum seal. I don't want to go to ford an get raped, diesel O-rings doesn't have parts for the newer pickups and I don't want to get junk from the parts houses. Where I can get these parts for a reasonable price? What the best brands are? Are they the same parts as the earlier super duties? I know the lock out is different.
View 2 RepliesFord Super Duty (1999-2016) :: F250 - Using Jack Stand On Rear Axle
Just got done rotating my tires on my 16 F250 ccsb 4x4 and I used jack stands on my rear axle while I used the jack on the front axle. When I brought the truck down off the jack stands (first time using jack stands on this truck) I saw that they left little marks/divits on the rear axle. I had them between the wheel and the shock support and I can feel with my finger where the jack stand was supporting the truck. It doesn't seem anything major but I can surely point out to you exactly where the axle and the jack stand met. I'm sure this is a non issue but just wanted to check in here to make sure...
No trailer attached (of course!) And nothing in the bed with a full tank of gas...so basically just the weight of the truck...
Ford Super Duty (1999-2016) :: 2005 - Idling Rough And Missing - Code P0506
2005 5.4l... Its giving me a code p0506 rpm to low idle air control system called for new one they said my truck don't have one said only up to 04 so what now truck idles rough n when u step on it it misses so bad its not funny feels like its laying over...
View 3 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Axle Stuck In Differential
Finally finishing up my 2001 F250SD 4X4 project. Decided to pull down the front axle to replace the dust seals. I've got everything apart including the large knuckle seals. Tried to pull the passenger side axle out but it only moves about an inch to an inch and a half before it stops. Took off the differential cover to look for damage or something obvious but I don't see anything wrong. The axle is moving within the splines of the spider gear but that's it. Stumped and sitting on jacks!
View 14 RepliesFord Super Duty (1999-2016) :: Replacing Rear Block - Axle Won't Separate From Leaf Springs?
I decided to go ahead and do a rear block replacement. I'm going to install the Ready lift 4 inch blocks.
I have both u bolts and nuts off of both sides. Rear stabilizer bar disconnected and both shocks disconnected. However, when I raise the rear of the truck, the axle raises as well. What could be holding it on still? I noticed there's a nut in the middle of the leaf springs. Do I take that nut off? I just don't know what could be keeping it from separating.
Ford Super Duty (1999-2016) :: 2008 F250 - Changing Rear Axle Ratio - Lower RPM?
My truck is a 2008 F250 6.4 Powerstroke 4x4 King Ranch, CrewCab, Shortbed.
I don't know which rear axle ratio it has - maybe someone can help me. the tires mounted are 275/60R17 and in fifth gear (TC locked) the engine has 2000rpm @ 70mph. I think it is a bit to much so I want to install a kit with and lower ratio. I pull trailers just sometimes and here in germany these only have 3,5tons max weight. So I think I don't need this power at 70mph. 1750rpm would be enough. How do I have to modify the front axle ratio if I get a lower-ratio-rear-axle?
I want to lower the fuel consumption. After some modifications, the truck needs round about 12-13L/100km (18-20mpg) and I think it is possible to lower this as bit.
Ford Super Duty (1999-2016) :: 2001 F250 - Rubbing Sound Near The Front Axle
I have a 2001 f250 7.3 4x4 today I locked the hubs, put it in 4 low and got threw some mud to go hunting fine. got back out of the woods and took it out of 4x4 unlocked hubs and went in reverse 30 yards.. Now when i drive it makes a weird sound like a rubbing sound near the front axle. What this is?
View 5 RepliesFord Super Duty (1999-2016) :: 2003 F250 5.4L - Axle Leaking On Passenger Side Rear Rotor And All Over
Here's my problem while replacing brake pads i found that my axle has leaked fluid on the pss,side rear rotor and all over .. I been looking for any info on repairing it myself . I found Everything for every other truck just not for this truck.
It's 2003 F-250 w/5.4L all Stock rear axle has 12 bolts and gears are 7.73 ... I believe its a Dana 60. No tags or markings on the Axle to go by..
I live in the Freak-en woods here so i like to order all the right parts once and do over the weekend .. its my only ride so once apart im stuck here.... I did check the Vent Tube its fine..
Ford Super Duty (1999-2016) :: 2003 F250 - Rear Axle Steel Brake Line Size?
I made a bone head mistake and crunched the steel brake line between the rear axle and the passenger side sway bar mount. Truck is a 2003 F-250 with a 7.3. I would like to go to the auto parts store, get bulk steel brake line and bend it myself. But, I don't know what size the line is or what size the fittings are. Whatare the sizes???
View 3 Replies