Got an '01 f350 v10, auto. When using steering column shifter tends to be hard to find reverse and drive. Is it something in steering column selector or is it in tranny? The truck has 40,000 miles on it. Have a parts truck also so just trying to figure out where to start first.
View 3 RepliesI'm looking at purchasing a 2003 F-350 from a Ford Dealer, Drove the Vehicle last night and the Gear shiftier was very tight and hard to pull down. Is this a real concern? The Sales guys said its better to be stiff rather than sloppy. But they will say anything, right. The vehicle is a deal and so I'm looking to find out why.
View 1 RepliesI had a new engine put into my 2006 F350 SD 5.4 last year and ever since then I can't keep the freon charged in my ac. The mechanic said all he did was lay the compressor out of the way and didn't disconnect anything ac related. I have 2 different shops keep my truck for a couple days and neither could find a leak. Yet a month later, freon is low. I think I have more dye in my system than freon.
I put 2 of those ac leak sealers, the ones you have to ask for behind the counter and can keep my ac working for maybe 45 days, then throw 3 cans in it. No dye is showing up nor will the sniffer find anything. I hate to go to the dealer because I figure they will want to replace everything. Any tips other than try another shop and maybe they can find the leak.
My buddy's 2001 7.3L F350 has had 3 transmissions. Rebuilt and used. Once the new trans is in he goes like 15 miles and then is starts shifting hard and grinding gears. What this could be?
View 8 RepliesI have a 2001 F-350 Diesel 4x4 crew cab 8ft bed dually 7.3 diesel 6 speed. The issue is that the parking brake pedal is extremely hard to push. One day it pushed down and ratcheted into a locked position as normal and the next day I couldn't push it more than an inch down. I have rear disc brakes with internal drums in the rotors for the parking brake assembly. I replaced the shoes and hardware (which were fine) and I still have the same issue. I removed the front single cable from where it splits into the two rear ones and the foot pedal depresses smoothly and with the touch of a finger with no load on it. What else is it? The only other thing is one of the rear cables unless I am missing something?
View 5 RepliesI have an '01 F350 super duty dually, 7.3L, auto trans. Over the past weeks my overdrive light on the gearshift would flash intermittently, maybe once every couple weeks. I chalked it up to a prior theft attempt where the steering column was damaged, and had turn signal/hazards issues after that.
Over the past few days my reverse gear has taken longer to engage, and is hard getting into the higher gears at speed. As of yesterday, reverse is out and won't shift out of second. Fluid level is good and clear. Could this be a PCM issue, or some sensor or relay?
I have a 2003 F350 6.0 King Ranch. My first diesel truck. Bought it in March 2016. One owner with 102000 miles on it. Has a Bullet Proof oil cooler and 4 inch exhaust. Truck ran great until a week ago. Now, under any hard acceleration it blows out blue/gray smoke and does not seem to have as much power. Coolant level is constant and I cannot find any traces of water and oil mixing.
View 2 Repliesi have a f350 superduty with a 7.3 turbo diesel and I pretty much hafta keep it plugged in to get it to start, i have installed all new glow plugs and both relays have been changed and the problem is still there, only other option i have not tried yet was changing the pcm controller but unsure if that is the problem ..
View 14 RepliesI have a 2011 F-350 6.2L that has extremely hard shifts from 3 to 4 going up and 2 to 1 going down. Sometimes on downshifts it feels like something has ran into the back of the truck. I had the computer updated when the truck had approximately 40,000 miles on it and he assisted a little bit. The truck now has 140,000 miles and it is back to shifting horribly. I put it in the shop at the dealer on 30 December 2013. The dealer says that the problem is that the shift solenoids need to be replaced but that they are not available. The truck is still sitting at the dealer and I am being told that the parts should be available mid February.
View 10 RepliesI have a 2000 F350 7.3 2wd Dually - that only only produces cold air conditioing on hard acceleration only stays on for a few minutes then falls away.
The temperature is cold when its going. I've checked the levels and its gased OK. There is no voltage to the clutch on the compressor when it is not working. So I take it, that it isn't the clutch shim/spacing.
If I accelerate hard it comes back immediately. Whether I am going slow at 1500rpm or doing 70mph at 2500rpm - Uphill or downhill. Its seems to need a substantial amount of Turbo boost for just a few seconds to turn on.
I actually bled the system a little and its made it worse. Stays on for a shorter time and isn't as cold. However the low pressure side is still on the high side at 50psi when running.
Its done this for approx 2 years and its getting worse.. And now its really hot outside.
2015 F-350 diesel purchased Sept 2104. When towing my 16,000 lb 5th wheel the 6 to 5 downshift seems to have gotten much harsher in the last few months. About 10,000 miles on the truck, much of it towing. Is this an indication of a developing problem?
View 1 RepliesI have an 06' f350 6Ltr. Over 300 k. Good shape, i have owned it for about a year. My first diesel. Last week it wouldnt start, had a 1/4 tank. Read about problems with other trucks with a broken pick up on fuel pump. So i filled the tank and it started. Next morning used command start and it ran for 1 minute then shutdown. took about 5 minutes of manually turning it over and it fires up ran all day. Does this almost everyday since and now shuts down while driving after hard acceleration and surges under acceleration when on incline or underload. Changed fuel relay, fuel filters. Researched and asked around but getting mixed opinions. I am mechanically inclined but this is a little beyond my scope of trouble shooting and id rather not start throwing parts at it.
View 1 RepliesI recently purchased a 2011 F-350 w/6.7 diesel. When I first start it & let it run say 30 seconds and take off it shifts fine from 1 to 2 but when it goes from 2-3 it hangs there a second and then finally shifts into 3rd hard. 3rd to 4th is ok but 4-5 again is a hard shift and from 5 to 6 is OK. It will do this for a while like through the neighborhood and down the road 10 miles then it is fine. Shifts beautifully when warmed up.
My local Ford dealer has a guy that is supposed to be very knowledgeable with Super Duty trucks. I have had it to him twice and he says this is normal. All shift hard until the transmission is up to operating temperature. Says the engine is very powerful and until everything is up to temperature this will happen. If so then it would be normal to let it sit and run for a while before you take off in the morning. I am getting ready to hook the truck up to my 33' camper and go on our first camping season with the trailer/truck combination and if I need to leave it sit and warm up I will.
Dealing with a 02 f350 7.3 powerstroke . The engine cranks fine . It fires but won't start smoke coming from exhaust while cranking and firing so seems to have good fuel . When it does start it misses for a few minutes and blue/white smoke . When the miss ends so does the smoke and starts fine after that and runs great until it sits for 12 or more hrs . Then back to same start issues . Fresh oil ,new glow plugs, new cover gaskets , glow plugs test at 1.3 ohm across all 8 of them , no voltage drop through glow plug relay , good voltage to each glow plug when tested right at glow plug terminal on each feed right at glow plug , fuel filter housing stays full doesn't seem to bleed back , high pressure oil pump pressure test was high enough to trash a 1000 lbs gauge in 2 to 3 revalutions of engine when cranking . Tested at presure sensor port .
View 2 Replies'08 F350 6.4l 4wd, I had the truck come in with a exploded transfer case. (See pics). Ive read all about this happening to many others. The truck still drove, hubs not locked, plenty of fluid in the TC, pretty sure it was the double Cardan that did it. Anyways I replaced thwith TC, replaced the front driveshaft, filled the TC with recommended fluid. Test drove and drives great, shifts fine. Only until I turned left.
At slow speeds turning hard or 15-20 taking a turn, it sounds like a ratchet clicking from somewhere on the left side, right around the drivers door, from what I can hear from the cab. Does it in 2wd, 4wd hi/low, hubs locked or not. I changed the vacuum pump, no leaks, changed the IWE solenoid, pulled out both locking mechanisms, tightened crossmember, checked everything from the hours of research I did on the internet. I cannot find the problem. I don't know what else to check. Front axles free spin and lock when they are supposed to. I'm at the end...
I have a 2005 F350 6.0 PowerStroke, and I just did the head bolts upgrade to the ARP studs, new EGR cooler and a new stock turbo. Looks like everything came out good, no left over parts or unplugged connectors, all new fluids and fuel filters and oil filter. Did the priming of fuel and oil, the turbo. When it was ready to turn it on, I turned the motor by jumping the starter to build some oil pressure.
Now I turn the key to turn on the truck, it turns with no issues, it sound good, but it will not turn on.
Checked my batteries, they are fully charged, checked fluids, ok, checked oil pressure as I'm cranking it, it looks good.
It still does not turn on.
So, I jumped it with my friends Excursion, after a couple of tries, it TURNED ON.
Let it run for about 3 minutes then turned it off. It sound good just like it did before the upgrade, with an exhaust leak from the turbo.
Went to turn it on again, it turns but it will not start, jumped it again and it RUNS.
Now I let it run for about 30 minutes figured out where the exhaust leak was coming from.
Shut it off, Re seated exhaust pipe with leak, WENT TO TURN IT ON AND IT WILL TURN BUT WILL NOT RUN.
So what checks I can perform to start eliminating possible issues.....
My 2011 f-350 6.2l cold starts hard, it cranks through 2 cycles sometimes before it fires, then it might stall. Sometimes it stalls if I put it into drive or reverse before its warmed up. It has also misfired on one or several cylinders during startup. It has also misfired while driving. It has never stalled when driving. I have replaced the canister purge valve, I have done a full tune up with all factory plugs. All with no change to how it starts. My next step is a Pcv valve, I have one coming from ford today.
View 5 RepliesI have an 03 F350 4x4 dually. Was pulling hard left at low speed when braking (front). Replaced pads, calipers, rotors, hoses and tires. Still the same problem. You can feel the abs activate right before it almost locks up the left front brake (basically will pull the steering wheel out of my hand). BTW the abs light does not come on.
View 2 RepliesMy 2000 ford f350 will start and then dies on me when i try to put in gear. I changed air n fuel filter. Adding oil i noticed the stick was still reading dry. Noticed a big oil spot under the hood. What should i try to do? Do not want to put in shop cause every time she goes in I come out broke.
View 1 RepliesI have a 1999 Ford F350 5.4L 4x4. I had a check engine code on my truck a couple of months ago. The truck was running fine then. The light went away and I forgot about the issue. In the last week the truck began to run like crap; hesitation during hwy speeds. The truck is running with hesitation in 3rd, 4th, and 5th gear. In low gears the truck seems to run just fine. I have changed the EGR valve as well as the fuel filter. Check engine light is not on but the problem has not gotten any better.
View 3 RepliesMy brother is having a issue with his 99 F350 diesel 7.3 automatic tranny pu. When in manual 1rst gear the engine stumbles and runs like crap. In drive or 2nd gear it runs fine. He's getting a code for a bad cam sensor. A new OEM and aftermarket sensor has been tried with no solution to the engine problem. What might be going on? Maybe a bad ECM.
View 2 Replies