Ford Super Duty (1999-2016) :: 2003 F250 - Misfire And OD Light Flashing
Nov 15, 2013
OK, quick question. I have an '03 250 with the 5.4 and the OD light began flashing tonight. I looked in the forums here and everyone say's new tranny or sensor but over on the diesel forums the are saying that the alternator is a big cause of this (dirty power).
At the beginning of this year I noticed what I assumed to be a misfire when putting the motor under a load. Once up to speed it would smooth out and all was good. I was told that a plug job on these trucks is hellish and expensive since a lot of guys break the plugs off in the block. I put it off and the issue went away when the weather warmed up.
Now it's getting cold again and the misfire is back. Driving home tonight the truck died at a light. I restarted it and as I accelerated I noticed a difference in the shift from first to second and then saw the OD light blinking.
Again, the diesel guys are all talking alternator so my question is this: could the alternator cause both the OD light to flash AND the misfire? If the "dirty power" can cause the tranny to fall in to safe mode, can it also cause the ignition to be problematic?
View 4 Replies
Advertisement
1998 F-250 LD 4x4 463,000 km.
My truck begins to flash the OD light after driving about 10 km. So I borrowed a friend's scan tool and got a P0503, and P1500. So having been pointed to the vehicle speed sensor, I connected TORQUE and watched closely vehicle speed. Driving at a steady 80 kph it will jump rapidly up and down, from about 72-92, while the gauge in the instrument cluster reads a calm and steady 80.
Which sensor and wiring do I need to inspect? Rear diff or on the back of transfer case? Oh, and the ABS light is NOT on.
Sent from Nexus 4. IB AutoGroup
View 14 Replies
I recentlyHad to replace the right front wheel bearing and after the install the speedometer and turn signals don't work, the ABS light is on and the overdrive light on the shifter is flashing. I've replaced the VSS on the rear diff, pulled and cleaned Speed sensors on front hub?
View 2 Replies
Tonight i noticed overdrive flashing. No changes in shifting, truck shifted fine. I shut it off when i got home, started back up, light was not blinking, not sure if its like the check engine light and stays on or not. Where light blinks but shifts fine?
View 10 Replies
Looking for a diagram of where the transmission temp sensor is found ..... I have a 2005 f 250 5.4l FX4.... My tow haul light keeps flashing...
View 4 Replies
I have an 04 F250 4x4 king ranch with a 6.8 V10.
When I first bought this truck it had a problem of stalling out at stops. You could sometimes hold the brake and gas and push your way through it but it would sputter for a second and try to die and then it was fine once you got going. The OD light would flash, check engine light would come on and it would throw a P0720 code for the OSS. I did some researching and I pulled the sensor in the pumpkin before that because I read that could cause the same problem, so I cleaned it and put it back but it didn't solve the issue. Then found that an K&N air filter can often times clog the MAF and cause the issue so I pulled my air filter and sure enough it was a K&N, I swapped it with a normal filter and sprayed some MAF cleaner and its been running like a top for months... until now.
It started again, gradually at first. It would die when I started to back the truck at a very low speed to load my 4 wheeler. I fired it up and it was good again for a couple more weeks, then I went to hook to a horse trailer and I was having to back up a hill to get to it, and it just kept dying, OD light would flash, check engine light came on. I was in a bind so I just tried wiping off the MAF with a rag, that didn't work, my girlfriend was using the truck and said it kept dying whenever she stopped. I got it home and cleaned the MAF with cleaner really well but the problem persisted. I went ahead and changed my oil, spark plugs(gaped at .052-.054), replaced the IAC(which looked like it had been installed once before so I am guessing someone tried it and when it didn't fix the problem they returned it) and changed the fuel filter. I drove it around and it ran fine, drove it to work and it ran fine, my girlfriend took it for about 15 minutes to run an errand for me and it was fine until she got back in the parking lot and liked to never got it parked again it stalled so much.
So I went back to the drawing board and read that it is rarely the OSS that is the problem but that often times the issue is a bad coil pack. I don't have a scanner nor do I know how the heck to use one. I plan on going out of town at the end of the week and the truck has 194k miles on it so rather then take it to a shop and try to find out which COP was bad I just decided to replace all of them(I know, I know, you should never just start replacing parts). I only had time to replace 5 of them, I took the truck out and again it dove fine for an hour, went through traffic OK. It sat for an hour and when I left it started to die again, I could drop it in neutral and it would fire back up and as long as I gave it just a hair of throttle it stayed running fine, take my foot off the fuel and in a minute it would die again. After I drove for a bit it was fine again. Now I know the problem may yet be in the remaining 5 COP that I must change tonight but in case it is not I wanted to get input on this.
I've read the problem can come from a bad ground, so I took every ground point that I could find under the hood and I cleaned the connectors and took the paint off at the connection site just for good measure. The problem persists. I've read that sometimes a diode can go out on the alternator and cause this problem, I did use my amp meter and I'm checking out at 13 volts while running. I'm not the best with meters so I'm not sure how else to check the diode?
I've also read that taking it to a dealership is hit or miss for them diagnosing the problem, sometimes they find the issue, sometimes they just change the OSS. The only mechanic I trust closed his shop and is now service manager of the Dodge dealership. I'm thinking since this seems to be a common problem that maybe ford might have more knowledge of it then dodge but I trust the dodge dealership more because of who is over it. Either way I know it will sit in a dealership for awhile before it ever gets looked at and if they have to chase any electrical problems then that starts racking up $$ fast.
So what am I missing? I've thought about replacing the MAF since cleaning it the first time solved the problem. When it did this the first time I still had my 01 F250(it never gave me problems like this) and so I took the MAF off of it and swapped them and sure enough it fixed my problem so I switched them back after I cleaned the MAF and like I said it's been running fine until recently. I'd rather not throw money at this by replacing parts and hoping for the best. I've also read about tracing the harness that runs from the sensor on the pumpkin to the OSS and on. That harness runs through all kinds of stuff so I'm dreading that but it will also be a next step. I haven't pulled the OSS because its in a very awkward position on my truck.
View 1 Replies
So coming home yesterday from our camping trip the tow/haul light started to flash. this was about 40 miles into the trip. So we pulled over, the tranny fluid looked low, so I added a little more. The light stopped flashing, but maybe another 20 miles it started again, we pulled over and it stopped. We got to a rest stop and after about 20 minutes, I called Good Sams Roadside, there tech said to take it out of tow/haul mode and so we left the rest stop and it was good for just about 40 miles.
We hit another rest stop, at this point we were about 80 miles from home. I did not feel any difference in the truck shifting or if it was acting different. The light flashed again, sometimes going off, then coming back on. We hit two more rest stops, letting the truck rest. We left the last rest stop, we were already halfway up a big hill on the Mass Pike and after 5 miles the light came on, but then after a few miles it stop and from that point to my house ( which was just over 50 miles) it never came back on.
The truck is a 2006 F250 gas that just hit 100,000 miles. New motor put in over the winter and a few years back had the cam phasers and some work done on it. Could this be some sensors, etc that is starting to go and needs to be replaced?
View 7 Replies
1999 F-250 7.3 Ext Cab 4X4... I just got this truck and it started having the 4x4 light flashing or flickering while driving and sitting?
View 3 Replies
What this could be? It blinks all the time was on the truck when I got it. Has a button in the bottom of it. This is on a 2009 super duty 250 and the 6.4 L if that matters.
View 3 Replies
I'm installing a new amber light on my 2013 F250 signal cab and was wondering where most people run the wires into the cab. It has a magnetic mount and I didn't want to put a hole in the roof. I have a cap on the truck and I also don't have a sliding rear window. This will not be a temp. install. Putting the wires in through a hole in the 3rd brake light?
View 3 Replies
F250 7.3L diesel started to flash OD light, goes into limp mode, code p1747. No other codes. Have had issues for a couple of years where the truck would not shift into gear for awhile; sometimes a couple of minutes till it would engage. Have done lots of diagnostics. Visual check harness. Have 12v on pins 1&12 on harness at transmission plug. Plug had some ATF visible, but cleaned it up and continuity good. (with 4" exhaust hard to get to connector).
Checked all solenoid wires with a DVM back to plug at PCM for continuity and shorts, all good. Pulled transmission pack and checked resistance on all solenoids except temp varistor all within specs. Removed Banks Trans Command and rewired tranny plug and pulled Ottomind chip from PCM. Still goes into limp mode and throws code. Did not see any bad solder joints or burns inside PCM by the way.
Seems like PCM right? But here is a complication to my issues. For over a year I have been having electrical issues like the radio not working and windows not working intermittently after starting up. After running for awhile or on restart would work fine. Sounds like the Instrument Cluster issues or relays.(?)
Will be pulling IC and checking for any bad solder joints. However, did not throw p1747 till just recently and now my radio has really gone wonky. It comes on when key is on automatically and then proceeds to cycle through settings; AM-FM-CD.
So questions are, "Is it possible that a bad Instrument Cluster can cause a p1747 code?" "Bad Ground to Tranny" "Can a bad PCM cause a electrical issue in IC??" "Are these 2 separate issues?"
2002 f250 7.3L, 4R100 automatic trans, ~180,000miles
Banks Stinger package, 4" exhaust, TransCommand, (now removed).
View 2 Replies
I have a 2010 F250 super duty. I use it for work so I am not sure what happened to it as others have driven it, but here is the issue. When i start it up in 2wd, the 4x4 Low light flashes continually. If I turn the switch to 4x4 high, the 4x4 high light flashes continually. if i turn it to 4x4 low, that light flashes continually. I have read the forums but haven't been able to find the problem/diagnosis for this.
View 2 Replies
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 Replies
I have been reading several past post regarding the misfire while in OD and going up a small hill with light acceleration around 45 to 55 mph. Everything points to the COP so I replaced it today. Still getting the code after 20 minutes of driving around. My truck shudders and looses power. I can either let up on the throttle or hammer down on it to eventually smooth it out and everything goes back to normal.
Check engine light flashed but didn't stay on. My scanner does report misfire on cylinder 7 (P0307). Haven't owned this truck very long so I don't know much of it's history except OASIS report shows nothing alarming. Guess next step is a new set of plugs.
Another first today, is the tachometer is stuck at 4500 rpm. Shut the truck off and let it sit for an hour, then went back to start and tach. acts like 4500 is the new zero and running engine at 1000 rpm now indicates 5500. 2007 F250 SD 5.4 ....
View 14 Replies
Just got the transmission rebuilt in my truck and other then shifting hard sometimes it has been doing great, Hooked it up to the goose neck this evening and everything was fine then went to back it up and pull it forward and after a short distance the od light was flashing and when i ran a check on it it was p0720? The transmission has less then 1000 miles on it?!?!? 1999 Ford F-250 7.3 Automatic....
View 5 Replies
I have a 2001 F250, 5.4, 4X4. My ignition key stuck in the start position and when I pulled it back to the run position, everything seemed ok. As I started down the road, my speedometer stopped working and my overdrive light was flashing. Also my turn signals had stopped working and my A/C clutch didn't engage. Figured I burnt a fuse. I looked in both the under dash and power distribution box and all seemed well. I checked the fuse for the turn signals/flasher and it was fine. The flashers worked. Thought I might have fried something so I replaced the ignition lock and switch. Also my service engine light came on throwing a code for the vehicle speed sensor.
Looking for solutions on this forum and the internet, I learned that the turn signal switch could have gone bad and the VSS sensor is on the top of the rear dif and an easy fix. Well replaced the sensor but nothing changed. So I went back to the fuse box. Examined every fuse, big and small and I found a 10a with a small space. This was #24 under the dash. From the manual, "#24, 10A, A/C clutch, Blend Door Actuator, Trailer Tow Battery Charge Relay Coil, Four Wheel Anti-Lock Brake System (4WABS), Turn Signal." Replaced it and everything went back to normal. Turn signals work, A/C clutch works, no flashing overdrive light and speedometer works. All from a 10A fuse. If you have any of these symptoms examine all the fuses carefully. There's a 20A fuse for turn/hazard lamps and this other one buried that's only 10A.
View 1 Replies
My father-in-law has a 2008 f-250 with the 5.4. as he was driving a while back all the gauges of the dash quit. The engine still kept running without any noticeable difference but when he shut the engine off and tried to restart, it wouldn't even crank but the security light was flashing. He tried starting it again a few hours later and it started just like normal and ran fine.
He has had this problem occur several times in the last few months, but the other day it repeated the problem again and would not restart for about 5 days. He has tried charging the batteries, changing relays, checking all fuses and finding none blown, scanned it with his code reader, and checked the steering column for bare or rubbed wires.
View 10 Replies
I have a 1999 f250 v10 auto. It has 3 miss fires thats im stumped with .. Ive replaced all spark plugs, all coils , I've had injectors out and were cleaned and it still miss fires. I can disconnect the coil and injector on the cylinders and the motor runs the same. Ive swapped the coils and injectors around to make sure it wasn't them. What else could it be? Frustrated I've had the truck for 2 years and haven't figured them out. Ive had them go away for at most a day. Also the truck has a shake at 80 kmh not sure if its from the miss...
View 13 Replies
I have a 2003 f250 super duty with a v10
i was towing a trailer up and down lots of hills and the battery light on the dash came on. there was no effect on the performance right away. as i kept driving into town i was starting to worry if i would make it.
as i pulled into the carls jr parking lot, the ABS light came on, all the gauges shut off and the truck died just as i pulled into a parking spot.
i figured it was the alternator, had it tested at AutoZone (failed twice) so i swapped it out for a lifetime warranty AutoZone one (very small town, nothing other than an AutoZone)
the truck started after being jumped but the battery light was still on. i figured that the bad alternator killed the battery. the battery was 4 years old and they usually only last 3 years in the AZ heat so i bought a new duralast gold.
the battery light was STILL on after that. the Autozone guy ran his test--- engine off- battery tested fine starting---he said something was wrong with the starter (but it cranked awesomely!) running--alternator tested fine
i just can figure out why when i drive down the road i dash light will turn on and off at random times. the truck seems to run fine. I've even been under the hood shaking the wire while i had someone watching the dash and i cant seem to make the light go on or off
View 1 Replies
How to diagnose misfire with no CEL? 2001 F250 5.4. What could cause it?
View 13 Replies
Have a 2007 F250 6.0 diesel with the standard issues including misfire at highway speed. Assume the bulletproof kit also cures the stiction problem? in reviewing the threads and looking at the vendors, references are made to fixing the oil cooler issue, egr issue, etc., but no one addresses stiction issue directly.
View 10 Replies
