Ford Super Duty (1999-2016) :: 2011 F350 - Stuck On Vent Mode
Nov 18, 2013
2011 F350 loaded. Stuck on vent mode. Found actuator can feel it trying to move but something is stuck. Tried to remove the actuator but not enough room between the motor and a steel bracket welded in to the dash. (Not removable). Do I have to remove the dash ? (I suspect something fell inside and is stopping the big vent door from moving as i did pull the motor far enough away to move all the door except the vent door.
View 2 Replies
Advertisement
I have a problem with my vent selector on my truck. It's a 2005 f350 lariat. The vent is stuck on defrost, some times after a few mins I can get it to switch to floor but not always. I have replaced the pump, checked tank for cracks, disabled and plugged the auto hubs. The pump will shut off so I assume it's not a leak. I believe it's in the switching unit, can these be repaired? I found a lot of dust and dirt in the vac tank that had been sucked through a bad hub. I think it may need to be disassembled and cleaned. I have seen videos showing how to replace the orings in the older units. Are the newer style remote ones the same?
View 5 Replies
Last Oct. I noticed that my ac/heater started to intermittently stop blowing from AC fresh air/recir/vent/etc. mode and stick to defrost only. Do I have a bad switch and or a vacuum issue here? It's a '01 F350 CC 7.3 .....
View 6 Replies
So my vents stopped actuating to different positions in my 2011 6.7 F350. I read that it could be a vacuum pump or solenoid issue. In any event, I turned 4x4 on and went down the street and made a u-turn - 4x4 seems to be on as the truck wants to hop the outside wheel when turning. I want to check the vacuum pump anyway but for the life of me cannot find it anywhere. Moreover, google turns up nothing which is making me start to believe the new trucks have a completely different system.
View 9 Replies
I recently purchased a 2012 f350 power stroke. Love the truck but went out this morning and the air would only come out of the vents. I couldn't get anything out of the defrost or the floor vents? Truck is out of basic warranty so want to see if I can figure this out myself or if it needs to go in the shop.I've looked for a fuse but didn't see anything that ran an actuator door.
View 5 Replies
I have a 2012 F-350 SRW with a 6.7 diesel. The other day I went to push the defrost switch and noticed it does not work. All the lights work in the switches, and the temp control works, but no matter what I push, defrost or floor, it stay in the vent only. Anything I can check??
View 1 Replies
About 6 months ago my 4 wheel drive stoped working and I wasn't worried about it because I never used it. I did mess around with it allitle bit to try and fix it the one time I did need it. Long story short I was involved in the floods near Houston these past few days but my truck was never in more than a a foot of water. I went up the store and grabbed a few drinks and went home. tuesday when I went to get in my truck to head back to college station for school it was stuck in 4x4 low. whick puzzled me because my 4 wheel drive hasn't worked in a good while.
When I turn the key on there is no 4x4 lights that come on momentarily and when I turn the 4x4 switch still no lighst come on. Again its been this way for 6 months. I tested the two relays under the hood and both of them have power. there is no power going to the switch in my dash and no power going to the solenoid on the transfer case. Wich is why I am confused on how it went into 4x4 low. I assuming it is in 4x4 low because of how fast the tranny shifts and I know its locked because I cant turn my front drive shaft while in neutral. The hubs are unlocked. I just printed out a shematic and am gonna try to figure out why my 4x4 isn't working.. to hopefully fix it so I can get my truck out of 4x4.
View 5 Replies
I am off to work tomorrow 800 Mile drive and I cant get this thing out of 4X4 Low. Tried driving (inching) back and forth. Got front end up on jacks to try to free up driveline... Is there any way to Manually put in 2WD. I just don't have time to run to town and get parts (new switching motor) if that is what the issue is?
View 7 Replies
I have a piece of a warn locking hub that is stuck in the wheel hub. It is stuck in a Ford F-350 super duty SRW 6.8 V10 with a Dana 50 8 lug front axle. Everything seems stock, but we bought this beast late in its life. I have removed the locking hub cap, the inner locking gear, and the metal retaining ring that holds the outer gear in place. The other side just falls apart as it should at this point.
I have tried building a custom puller utilizing the 6 hex cap screws (that attach the locking hub cap) to pull in on two 1/8" thick c channels held off with a 1/2" bolt pushing in the middle of the c channels on the axle. In one case, I sheared off the bolt, and bent the c channels. I tried it again and that time broke several of the hex cap screws off.
I have ran through penetrating oil, wd-40, propane (for a torch) and carb and brake cleaner as I tried heating up the hub while applying penetrating oil and letting things sit, then spraying out rust and such with carb or brake cleaner to loosen things up, then repeating the process over and over again. I have done this process several times. It worked on the center where the axle goes through the inner gear, so now the inner gear is now loose from the axle. But the outside is still suck like no other.
Lightly hitting on it with a 3lb sledge to crack something lose has done nothing, and left me struggling not to beat it much harder with a bigger hammer with a longer handle.
As a note, it took weeks to get the center locking gear to fall out after doing the oil, heat, and spray cleaner process, then driving with it locked in, and it took two attempts and hours to get the cap off from stuck hex cap screws, several which I had to drill out in the end after even an impact screw driver would not work. The U-Joint is bad, and I can't lock in the 4WD which is problematic at the dump and on job sites when it is muddy especially when we are towing a maxed out 5k single axle trailer that wants to dig in to the mud too.
View 6 Replies
One of our trucks, 2004 F350 Powerstroke, my company truck, recently the last snow even we had, my tow haul mode would pop on and off almost evertime I shifted from drive to reverse while plowing. I didn't want it on, it just kept poping on and off. Thought maybe the button was stuck, but it moved like normal. My other thought was there is a loose connection in the shifter or column causing it to go on and off.
View 6 Replies
Replaced HPFP 38,000 miles ago. Truck began going in limp mode without engine light, wrench came on in dash, gave codes for brake switch, anti-theft, some other weird codes. Had those codes cleared, ran for while then water separator came on, drained the water out, came back on. Read some forums, so I removed and cleaned the housing, cleaned off the sensor. Had code cleared and ran good for about a week. Then guess what engine light comes on, limp mode.
Went to Auto Zone, pulled code P0088. This truck runs awesome until limp mode. No other problems. I take it to the ford dealer, scanner pulled P0088 and the water separator code again. I have read alot of remarks about this P0088 code. Can there be another cause for pulling this code, only 38,000 miles later. I had them do the TSB 12-07-07 but I have also read it can only be done if the P0088 is the only code. I just really feel there is an underlying issue with these 6.4's.
View 3 Replies
My question is my abs light came on so I stuck my computer on it. Said right rear , we'll we all know on a 2007 6.0 f350 4X4, the there's only one sensor on the pumpkin, so I replaced it and cleared the code. Abs light came back on once I started driving, week ago my right front caliper stuck and got very hot, could that read bad for the rear of the front went bad? Will pull plug and make sure I didn't bend any pins.
View 2 Replies
2011 250 run fine when parked it Friday jumped in it Monday morning got a check traction control light on will not shift out of park no break lights replaced break switch all fuses are good.
View 5 Replies
Came out to start my truck today a hit the key and got nothing. After I settled down from being upset about my truck already giving me trouble (bought it in Nov and had 25k miles on it, 35k now) and that I should have stayed with a Chevrolet, I was able to start it by crawling under and jumping the started with a screwdriver. The truck started up no problem and got me home where I did some troubleshooting. Looks like I dont get solenoid power at the starter (just main power), the relays and fuses checked out, anhe d it looks like the key is still programmed.
I had been getting what seamed like a delayed start every now and again that was going on for a while, but thought it was just me. The next items I thought that may be the culprit are the neutral safety switch or the ignition switch. The gear selector seams to work fine and it wont start in either P or N, the backup camera turns on and nothing seams to be incorrectly working on that account. Also, the truck is a 2011 F350 Crew Cab 4wd Lariat with the 6.2 gas motor.
View 10 Replies
Ok so I got a good deal on a used F350. When I got it home I found the heater was stuck on defrost. I posted on here a few weeks ago with questions on what could be wrong. From that post I learned that my front passenger side hub is stuck locked in. I pulled the vacuum lines at every connection from the pump on and had good vacuum all of the way to the passenger side hub. I turned the axle shafts and found the drivers side is free the passenger side is locked.
I flipped the dash switch and heard the drivers side hub lock. Then I turned the axles again and found they were in fact both locked in. I flipped the switch back to 2H and the drivers side freed and the passenger side was still stuck locked in. So I pulled the passenger side hub off of the truck and found it was seized up. I put it back together and locked both hubs in manually until payday when I can pick up a new hub.
Yesterday we had a lot of ice! Where I park the pickup the front wheels drop into a low spot. I could not get backed out of my driveway with the front wheels in the hole and the rear wheels on ice, so I flipped the switch to 4x4 and tried again. It still could not pull out, the front wheels didn't seem to engage. Now I am thinking I have more troubles than just the one hub stuck locked in.
So, my questions now are, 1 if the passenger side hub is bad but both are locked in it should still go into 4x4 correct? 2, the 4x4 light on the dash lights up when I flip the switch. If I had a bad switch or fuse would I still get the same result (light on and drivers side hub clicking in)? Does this pickup have to move a few feet before it engages the 4x4 or should it click right in? And finally what is a short explination of how the 4x4 system works. The dash switch engages the solenoid on the firewall to switch vacuum down to the hubs but what else does it do? I assume it has some kind of switch or motor in the transfer case that engages the 4 wheel drive?
View 14 Replies
I bought a 2011 F350 that was in a collision. I have done collision repair before but I have not had to deal with air bags... Both driver wheel and passenger bags deployed. I see some for sale on EBAY for around 300 used....do I just by them and install them? Is there a reset or something else I have to do? I see some sell them with the controller as well...do I need that?
View 14 Replies
I have an 11 F350 6.7. It has just under 200K miles on it. Yesterday I changed the oil. Very uneventful. Today however, I was driving home, about 100 miles, and my truck's temp spiked. Not like a little spike, but jumped to the 3/4 mark(if there was one) then slowly kept rising to to the overheat mark. I pulled off onto the hard shoulder waited an hour or so to let it cool down, then finished the drive home. All the way home my temp gauge seemed like it was on some sort of drug. It would jump a needle width when I would have to accelerate, then slowly cool to normal after I got up to cruising speed.
When I got home I checked the oil level and it was spot on in the "normal" range. I haven't used a different type/brand/weight of oil in the last 100k miles. Did something just give out on my truck? I had the coolant flushed and replaced at the dealer within the last 10k miles. Up until this point this truck has been exceedingly reliable. I pull a 13k 5th wheel once a month and drive about 40k-ish miles a year.
View 9 Replies
I just bought a 2011 F250 Super Duty 6.2L and the manual A/C buttons were stuck on Max A/C and wouldn't change. I fiddled with every switch on the dash thinking it might be a stuck switch and eventually all the buttons started working. This truck has SYNC, which works fine, and I can't find anything else wrong with the truck.
When the buttons are lit, it blows good and cold, in A/C and Max A/C. The problem I'm having now is that they won't light up at all. Visual inspection shows nothing obvious under the hood, and it has a charge of freon. I drove and it id working just fine, but stuck on the Max setting. I'm thinking electrical gremlins, like stuck switch or a relay...
View 1 Replies
I have a 2011 F350 with the towing package. I got it used as it and it was a northern truck. My towing mirrors won't extend in or out. They fold and unfold just fine. When I press the button to telescope them I can hear the motor running so I know the fuse is good. I took the glass off the mirrors and scraped some salt out of the joints. I sprayed some lube on the joints as well but still no luck. I also tried forcing them but not too much to avoid breaking them.
View 1 Replies
I have a 2011 F350 with camper package (didn't want it). When I drive on a bumpy road (without 5th wheel), the truck suspension does not absorb the shock. The ruts just throws the truck side to side. Really hard, so I can't go on a dirt, rough road. On one bump it poped off my rear tire cap.
My problem may be with the camper package trying to keep the truck from going back and forth.
There is a 7/16 inch steal rod going from the truck bed, around the differential, and back up to the other side of the truck. Is that the rear stablizer rod?? Can I disconnect it? What would be
View 13 Replies
2011 F350 with fluid leaking in through the firewall. Does the Hydro booster have to be replaced or is there a gaskets or seal on the rod that goes to the brake pedal?
View 14 Replies
