Ford Super Duty (1999-2016) :: Bull Whirring Noise / Vibration When Driving
Feb 27, 2016
2002 F250 4x4 ... There is a bull whirring noise that started about 4 months ago. I attributed it to tire noise. Then this past winter I put the truck into 4 wheel drive and it went ok, however everything started vibrating. First thought was u-joint however none are loose. Then I thought needle bearing, the axle has no play in it at all. So I looked at the drive shaft, it has a sloppy turn, not sure on how much play it should have.
Then you turn it and it then kind of binds up, you can push through that bind then it goes until it hits that spot again. I jacked the truck up and turn the wheels there is no noise. The noise is only when it is driven. Took it to ford and they came back with nothing, they replace the rear pumpkin gasket and cover stated those gears where fine and they inspected the rest, and came back with nothing. Should I just start by replacing front hubs and bearings and see what happens.
View 1 Replies
Advertisement
So I'm going to be putting a deposit on a 2012 6.7 dually tomorrow after work. It has about 40k miles 2800 hrs 1400 idling. It looks perfect. Drives good, sounds good except for a bit of a whirring noise occasionally under the drivers side floor (fuel pump maybe?)
For warranty I still have the remaining 2 yrs, and the miles left. I am going to try to get them to give me 5 more years on the powertrain. Before I pass the check is there anything I should specifically look for? It is a beautiful truck ....
View 2 Replies
I recently checked and changed the one bad ujoint in the rear shaft but I still have a vibration once I hit 35mph but doesnt happen all the time and sometimes goes away while driving.
View 2 Replies
01 F350...4R100/V-10/4wd. Sometimes get a vibration driving down the road. First thought of tire out of balance but then the vibration goes away and may not come back for a few days or more. It starts sometimes around 30-40 mph and stays all the way up to around 65 mph. Even slowing down it vibrates or shakes. I can stop and take off again with nothing happening. Would think tires out of balance would do it all the time. And a few times....pulling my 5th wheel...making a right turn out of a parking lot.....it feels like a rumble from the rear.
View 2 Replies
I have a 02' 250 4x4 with 250000 miles on it. While driving between 55 to 65 mph there is a roar and vibration that seems to be coming from the rear. I have about 35% tire tread left and have had the rear tires balanced and it still does it. Having issues with drive shafts unbalanced or rear ends?? I am not sure where to start....
View 1 Replies
I have a 04 F350 srw , 6.8 . Recently developed loud whine from the rear . I had the differential (10.5 sterling ) completely rebuilt . It quieted way down . But I still had a couple of high pitched whines . Took it back and had the rebuilder ride with me . At first he couldn't hear it ( it can be faint but gets louder under a load , I pull a 40' trailer and didn't have it with me), when he finally started hearing it he said it might be a planetary making a little noise, just watch it . So I made a short run (450miles RT) . Same noises but I noticed that sometimes when I stopped and got fuel , it would quiet down for 50 or so miles . I got to thinking maybe it could be a rear wheel bearing going bad and the sound transferring through the axle to the drive line . It only did it accelerating ( before and after rebuild ) and got louder going up a hill .
Today I drove it in to town and parked it ( still the same ) and a couple of hours later after a cold front came through ( maybe 10 Deg. temp change) I got in and the noise was about 90% gone , but at 45 to 60 mph. it vibrates . Let off the gas , vibrates ,, Put it in neutral- vibrates, revved the engine in neutral - vibrates and no change from rpm diff. . As long as its rolling between 45-60 , it vibrates . Hit the brakes- vibrates.. I have had 3 mechanics check it out ( 2 good ones and one that the other 2 take what they cant figure out ). Left them all scratching their heads. Checked the driveline and I changed one U joint (prior to the short run ). All seems tight .
View 4 Replies
I've been chasing a noise/vibration that periodically comes from the front end of my '99 F250 SD. Quick & dirty of it........basically while cruising 55-60 down the road, sometimes when I hit a bump in the road or go over some railroad tracks or something like that I will get a grinding/vibration from what sounds like the front drivers side wheel. Best way to describe it is it literally sounds like my wheel is running on the rumble strip on the edge of the road at road speed. It will fade in & out a little & last maybe 5-20 seconds & eventually quite until some time farther down the road if I hit another bump. Doesn't happen all the time, just randomly.
So far to try & problem solve I have lifted the front & spun & kicked & wiggled & pulled on the wheel to see if I can feel or hear anything & everything seems solid. I have pulled the wheel off & looked the whole hub & wheel bearing over & everything seems fine. I have even pulled the 4x4 lockout out & inspected everything in the lockout & inside the wheel bearing & can't find anything that seems to be bad. (My original thought was that the Warn hubs I have might be messed up & the hub is trying to engage while driving down the road & that is the grinding & vibration I'm feeling.).
As mentioned above I have Warn manual hubs, I just replaced the wheel bearing last summer (only have about 10,000 miles on it), & all the seals & ball joints were done about 3 years ago.
View 11 Replies
I have a 2014 super duty extended cab truck and at times I get a vibration noise which seems to come from somewhere around the antenna. The little rubber flapper at the base seems to move and isn't tight against the metal. Is this causing the noise...
View 4 Replies
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
View 8 Replies
The other day I pulled a fella out of a ditch. It was a dulley 350 with a lowboy trailer and a small dozer on it.
Well, after finishing and driving away. I inadvertently left the truck in 4x4 while driving on wet pavement at speeds ~30 mph. What I noticed was: when I let off the accelerator there was a low growl/vibration noise coming from the front/under the floorboards while the truck coasted to slower speeds.
I have never had my truck A) in 4x4 on clear roads or B) at speeds above 10mph in 4x4. Maybe they all make noise at low speeds in a quite cab in 4x4. I wouldn't know, I've never driven it under these conditions.
So, can you hear your truck in 4x4 when not giving it gas and coasting on the road?
I did not think I put the truck through too much while pulling that fella out, but now I'm wondering....oh, and I at one point I coasted forward and ran over the towing strap that was attached to my front pull hook and it made a HECK of a noise...could that have done something bad?
4x4 still works, and everything seems/sounds fine otherwise. I might just be hearing the front end putting friction on the transfer case and I can hear it in the tranny as she coasts to a stop (it goes away as soon as I press the accelerator at any speed) but like I said, I've never noticed this before.
View 8 Replies
I have a 2000 F250SD 4x4 that has developed a nasty front end noise. I originally thought it was a suspension issue (seems like bumps in the road cause the noise but not always, turning does not cause it) but everything seems good. Steering is tight and there is no 3 and 9 oclock movement. Ball joints also seem good with no 12 and 6 movement. I have jumped up and down of the front bumper and cant recreate the noise either, removed the sway bar and the noise is still there. The only strange thing I notice was that with the truck in 2wheeldrive and the hubs unlocked I can turn the front drive shaft and the drive's side axle spins but the passenger side only turns intermittently. I'm sure this isn't right so I'm looking for diagnosing the cause. Since none of these parts should be moving while driving in 2wheeldrive could this also be the cause of the noise?
View 11 Replies
2003 F350 4.4 5.4L auto. The front hub assemblies, seals, axle ujoints and upper/lower ball joint were all replaced. I bought all the parts gave them to the mechanic and told him if there's problems call me. I took a week off went to MS and he never called. I go to get truck he tells me, the bearings in the hubs are not spinning freely causing the axles to spin. I checked the hubs they are in the unlock position (Warn manual hubs). Originally auto hubs. Now i have the whole front diff spinning and the front drive shaft is spinning too. Clacking and clicking from the front wgen driving. Oh he said the front drive shaft ujoint was bad also. I paid $600 to have it all replaced and i get it back wrong. Is there something i need to check on the hubs that he maybe did wrong? Or is it possible i was sold the wrong hub assemblies?
View 14 Replies
Have a 02 v10 125xxx miles have had grinding noise on drivers side sounds like driving on rumble strip took out the unit hub everything looks good changed out the needle bearing because it was frozen still have sound after needle bearing replacement sound goes away if hubs are locked so question is it the unit bearing or stub shaft...
View 2 Replies
2003 f550 with 7.3, suddenly loses power and struggles while driving. White/blue smoke comes from tailpipe, can smell the diesel exhaust bad when happens, comes and goes intermittently but has been happening more and more often. I uploaded a video onto YouTube to show sound, rough running motor and smoke from exhaust although smoke not that bad in video. Search "shadetreelandscaping" on YouTube in case link below doesn't work.
ShadeTreeLandscaping - YouTube
Took to ford dealer a few diff times for problem and they can't get any codes, can't duplicate problem. After it being in for third time they say had to call ford tech hotline and they suggest replacing injector however can not and will not gaurntee that will solve problem, and obviously dealer isn't cheap for repair. I find it hard to believe that a bad injector(s) would be an intermittent problem as it is or that it would cause fuel pump to make gurgling sound.
View 13 Replies
I bought this Ex a little over a month ago and finally got around to replacing some stuff.
I have a slight vibration between 50 and 60 MPH. The vibration is the same weather I am accelerating, in Neutral, Coasting down (well, a little bit worse when coasting down), in 2WD, in 4WD, turning, going straight, hot or cold.
I have replaced the following:
Rear Driveshaft U-Joints
Tires and Rims
Upper and Lower Ball Joints
Wheel Bearings
Steering Stabilizer
Cleaned and Greased the Hubs
Greased everything greasable up front
I still have the exact same vibration as when I started. I can feel the vibration in the steering wheel as well as in the body of the vehicle. I am thinking that it may be in the steering linkage. If there is a loose joint then the wheels would be allowed to jiggle a little bit. I am at a loss. What else should I check?
Also, When doing the ball joints, I noticed that the tie rod ends were quite stiff. How stiff should these be? I can't move them by hand, but they will move a little bit when moving the free end of the tie rod.
I am taking it in for an alignment on Friday, and if I can't figure this vibration out, I might have them take a quick look into it. Would a stuck slide pin in the front brakes do this? Both sides on my truck are seized at the current moment.
View 14 Replies
I have an 2011 F250 gas. I get what feel like a wheel vibration at 48 to 50 mph. It then go as you go up in speed. Comes back as you go down in speed at about the same range. Had it at the dealer for a month they but new tires and one new wheel on the truck. Same problem. Moved up to Ford. The sent me to another dealer. Ford now tells me that this is a problem that exist in the truck and there is nothing they can do.
View 14 Replies
So I have a 2016 6.7L love it but it has this vibration at 65 mph that is worse when accelerating up a hill. It feels like an out of balance wheel but I have had them balanced 3 times. road forced 2 times. My dealer replaced the driveline also. I did a test with 400 lbs of concrete bags in the bed and it was vibration free. It almost is like the pinion angle is off.
View 11 Replies
Tires just balanced and rotated yesterday (second time just in case done wrong before). New ball joints and bars installed about 50k ago. Left front shock may be bad, but only slightly.
The issue: At about 40-55 mph, there is a rumble in the cab, unknown origination. Everything vibrates, although it "seems" like the left mirror is shaking more. The seat, floor, steering wheel, everything vibrates.
When I let off the pedal, vibration and noise go away, even within the "vibe zone". It only vibes when any throttle is applied, even just a tickle. I brought the engine up to the vibe zone RPM (1500-1800'ish) while in park and neutral, all seems fine.
I checked the U-Joints, they seem tight. I don't have access to a scanner, unless I want to pay the dealer.
View 14 Replies
"2004 Ford F250 FX4 for sale. 5.4l v8, automatic transmission, 4x4, 152,000 miles. Truck runs and drives good but needs a rear drive shafts due to a vibration above 50mph."
Are their any known issues with these? I am guessing it is a u-joint or something, not the driveshaft.
View 3 Replies
A vibration has just begun on my 00 f250 power stroke it's in the left front and happens when I hit a bump I changed out the wheel bearing assembly and I switched locking hubs with another truck all with no success don't know what else it could be it does go away if I lock in the hubs so idk
View 2 Replies
I have a 2011 f250 6.7 and I have a very bad vibration between 40-50 that seems to peak around 45-47. It also starts again at 80+ . the dealer told me they could not find a problem. Then another told me its normal. The tire shop around here told me the tires were shot so I bought new tires. No luck. It does not affect it if I change gears.
2011 f250 4x4 6.7 SWB. 140,000 miles
View 11 Replies
