Two Issues....
1.My rear dome lights work when manually turned on. They do not come on when the door is opened. However, the front dome lights do.
2.The lights on my side mirrors turn blink when using the turn signal, and when hitting the lock/unlock/remote start buttons. They do not work when driving around with my head lights on.
I have a 2011, F-350, Lariat, Crew Cab, 4x4, 6.7 Stroker. I have asked if any way to disable the automatic feature that turns on the marker lights when opening a door. That has been sometime back and nobody seemed to know. I have checked with Ford and their response was that if the truck was equipped with the "Police Package" that it could be done.
There has to be a way to disable a relay, cut some wire or something to stop the lights from being turned on automatically. Maybe duct tape over the door switch?
My dome light does not work and door ajar light is always on. I cant even turn the light with the switch on the side. Just don't know where to start. Do you think it is a switch on one of the doors? I have tried spraying cleaner and WD40 in there but it has not worked. Its been this way since I bought the truck but it is starting to drive me crazy....
View 2 RepliesI just purchased a 2006 E-350 15 passenger van. ~85000 miles. As soon as any door (except the very back door) opens, the dome light comes on, as expected. However, when you close the door, the light doesn't go off. There are two ways I've found to make the light go off:
1. Reach a speed of 10mph
2. Wait several minutes (i haven't timed it yet, maybe 10 min?) without opening a door
I've read that the keyless entry remote can control this, but this van isn't equipped with keyless entry. There must be some factory setting that can be adjusted. Also, any thoughts on adding an aux jack to the stock AM/FM/CD stereo? Maybe I should bite the bullet and install an after-market deck?
I noticed tonight, that my driver's side outside rear view mirror is no longer defrosting. I can't really say when it last worked, we haven't had much bad weather here, and just in the wildest case that it may be relevant, I just recently had my master cylinder replaced under the Ford Recall. Why a mirror would stop defrosting?
View 2 RepliesI'm having a problem with my interior dome light and my door chime bell not working in my '01 F-250. I found that the bulb was blown,so I replaced it thinking it might fix the door chime bell also, thinking they were wired together from the factory.
The new bulb didn't fix the problem. I recall that when I noticed the door bell didn't ding-ding anymore was about the time(when it got dark), that I noticed the dome light was out also.
What I may check? The fuses all work, the interior dome relay switch works and I see nothing else in the owners manual to look for as far as dome lighting and door bell chime.
So I read the posts on dome lights staying on and the solution to spray WD40 in the latch but my problem is the opposite. The light sometimes comes on, sometimes it doesn't, when the door is opened, same if using the dash switch, sometimes light, sometimes darkness. Sometimes it just barely lights up, and I see its an LED in there. 2004 2wd Edge 2 door.....
View 4 RepliesHave a 06 and the dome lights stay on all the time. I had to pull the bulbs out of all of them. They would come on during the night and run my battery dead. The lights just come on while driving down the road and won't go off either. I can hear a clicking in the dash while driving where they are coming on and off from a really or something. Sounds to me like it's coming from the instrument cluster.
View 5 RepliesI was replacing the dome light in my 06 Ford F350. I tested the light and it worked then while screwing it back in, the lights when out and then the radio. I suspect it may be a fuse, but have yet to find the culprit.
View 2 RepliesWhat the code "32" means for the airbag? Lately my airbag light on the dash will blink 3-2 for several cycles then stays on solid til I shut down the truck.
View 12 RepliesMy 2008 F250's passenger side mirror will not fold/unfold with the switch. Also the motor continues to run when the switch is moved to fold/unfold the mirrors.
View 4 RepliesI can't find out why my dome light doesn't work. I threw a bulb at it first, and then a tester but found no voltage with the door open or the dome lights dimmer roller clicked over to "interior lights on". I do get a door chime with the door open, so seemingly the door switch is working. Fuses 4 and 14 are good. They seem to be the related fuses.
Here's what I've checked.
1.. Fuses are all good.
2.. Removed and tested the relay. It tested properly, closing the large contacts when voltage is applied across the two coil terminals.
3.. 12V is present at the large left contact in the relay plug.
4.. I applied voltage to the relay output pin (the large contact next to ^^) in the fuse panel and get the dome/cargo lights to illuminate, so I know the wiring from the relay to the lights is good.
5.. The two smaller relay pins upper and lower look to be the relay coil/turn on contacts. (The middle contact is not used) There is 12v on one of them and it seems the other should be grounded with a door open or when the dash roller is rolled past the detent. I'm not getting this grounding signal.
6.. I do get a warning chime if I open the door while headlights are on etc, so it looks like the door switches are working.
Just got back in from some more testing... Here's a breakdown of how the relay works:
- Relay socket we're looking at is the upper socket.
- High amp 12V power is on the left large vertical contact. The relay's function is to port this voltage to the middle large vertical contact. (the load contact)
- The middle vertical contact (load contact) goes to the dome light and cargo lights.
- The upper horizontal contact is one end of the relay throw coil. This one has 12V present when probed.
- The middle horizontal contact is not used. (actually it's an empty socket with no female terminal behind it.)
- The lower horizontal contact needs ground applied to it to get the throw coil to close the high amp contacts.
With the relay plugged in, I was able to sneak a thin probe to the lower horizontal contact and ground it. The relay activated and the lights came on. So, for some reason I'm not getting the grounding signal to the relay with the dome light rocker or the doors open even though I get the door chime.
Apparently there is something between the door switches and the dome light/roller switch and the relay? Is this the GEM module? If so, I don't see the reason for anything between the switches and the relay? It should be a pretty basic relay circuit?
Is this something (GEM?) programmable, or testable? I don't want to throw parts at it. Looking for a wiring diagram, a diagnostic flow chart or a pin out?
On a 2008 E250, Where is the dome light wire and what color is it? To use with an omega security system.
View 4 RepliesI have a 2004 V8, and now that it's a bit darker in the mornings and evenings, I've noticed that the dome lights ahead of the sunroof do not illuminate when I open the door. Strangely, the dome light over the back seat illuminates when either the front or rear door is opened. Any way to get the illumination in the front of the car? The lights work fine when operated manually, by the way.
View 2 RepliesMy Viper 2 way alarm, instead of the brain being wired to each of the 4 doors individually. The installer ran 1 wire to the dome light. Seems to work fine as far as arming/disarming/locking/unlocking, but since the dome light stays on for 10 seconds or whatever after the door is shut, when i arm it.
The 2 way remote says "door open" because the light is still on so it thinks a door is open. this eventually times out and all the sensors arm, but there's a long delay. it arms fine and no alerts pop up if i lock the doors first from the outside keypad on the door, making the lights go off, then hit arm on the viper, and everything is good to go.
Can I change it so no matter what, as SOON as i shut the door, the light goes off? I want there to be NO delay, if possible. If not, I may need to just have the installer run a wire to each door and take the single run to the dome light off, as it is sorta annoying to me.
I have a 2012 Santa Fe and the front map light fixture was where my issue started. I believe from what I read that the diode had gone bad because the map lights would work if the light button was pressed, but not if the door button was pressed. At that point, the only issue I had was the light now working when the door opened. So, I ordered a replacement part and tried to install it today. It was harder to get the old one out than last time, but it came out no worse for wear and I unplugged the old map light fixture. I plugged in the new one and it did not work at all. I checked the wire and it looked fine, the prongs and they were fine and tried it again... nothing.
Now, the back seat dome light and trunk dome light don't work either. (with the new map light plugged in or not) Old one back in and still nothing. Checked the manual for the fuse that is supposed to control those lights and it is fine. I got frustrated because it made no sense and gave up for the night. (no light is even plugged in where the map light goes for now) I come in the house and now every hour or two (when I lock the car) the alarm sounds for no reason. The alarm button won't shut it off either, I have to hit unlock and it stops. (3 times in the last 5 hours now) So, I have decided to leave it unlocked for now. So far, so good. BUT, I need to lock my car when I am out without the alarm sounding and I need my dome lights working. Everything else with / in the car seems to be normal.
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 RepliesI'm trying to find the wiring diagram for the power windows in a 96 f150. I've got a set of these that i need to fab a harnes for to install in my 82.
View 12 RepliesOk, I admit this isn't on a Ford, it's my old man's 1970 AMX, but it's an odd electrical problem we can't figure out. The front right blinker works fine when the headlights are OFF but when the headlights are on it doesn't blink. The other three work as they should. He has tried new bulbs, ohmed and voltage tested the sockets. Ohm reading was around 1-2ohms and voltage was 9v.
The voltage also fluctuated when the blinker was on but when you put a bulb in it didn't blink. He has noted the bulb on the passenger side is brighter than the other side. He's trying to get it ready to take to Pigeon Forge next weekend for a car show and I 4.5 hours away. What could be going on??? Could a bad headlight switch cause this? Bad socket?
I drive a 2004 Ford Ranger. When I use the remote to unlock my truck, there is a grinding electrical sound, and the driver side door does not unlock. The passenger side does, though. Also, when I try to use my key to unlock the door, the driver's side door will not unlock with the key. I can open the driver's side door from the inside by using the handle, but the electric lock button will not unlock the door. It seems like the piece that pops up when the truck is unlocked has a hard time raising to unlock the door. Neither my boyfriend nor I can figure out what the problem is. I find that when I take my truck in for any problem, people at the dealership try to take advantage of the fact that I'm female and don't know much about cars. Need to know what is going on before I take it in anywhere to get fixed.
View 1 RepliesI would like to add an LED light to each running board and tie it in with the dome light wiring so that when the door(s) are opened it will come on with the dome light and light up the factory running board. Any info on where a good place to splice into the wiring, and will the wiring be able to handle a couple extra lights?
The truck is a 2012 F-350 XL, SD Dually....