Golf IV / Jetta IV :: OEM Muffler Replacement Without Lift?
Jun 19, 2014
I removed the old muffler but it was severed at the pipe so there was no issue getting it over the rear cross member. I dropped the center brace to remove the resonator from cat back.
My question is, is it possible to install a new OEM rear muffler without a lift? I have stands but I do not know of I can get it high enough, or if I even need to get it that high? Not sure the bend of the pipe before it meets the resonator.
View 4 Replies
Advertisement
Putting a magnaflow muffler on the 99.5 2.0 slow jetta on Wednesday and I realized I don't have a rear GLI lip. Any single turn down extension off a muffler ? Or just run a straight pipe off the muffler ? Clearance with the rear lip issues ?
View 4 Replies
So I installed coilovers a short while ago and now I need an alignment bad (obviously), but when I took it to get aligned, I was told my car is too low to drive up onto the lift , so I was wondering if I would be able to adjust my coils to a better height and then after the alignment just drop them back down a bit, it won't be too major of a drop back down but I just want to make sure I wouldn't be wasting my money. There is a place up the road that will do the alignment at my current height but for a pretty steep price considering how low my car is.
View 10 Replies
I am replacing the mid and rear (suitcase) mufflers on my daughter's 2001 2.0L Jetta wagon. She is not interested in anything that would be louder than stock. What I am seeing is that the rear axle needs to be dropped to remove / install the rear muffler. Can this be correct? I know I can continue to cut off parts of the old muffler but that does me no good when it comes to install the new unit.
View 2 Replies
I was driving home and suddenly the underside of my car *popped* and it sounded like my muffler came loose. Very loud exhaust/turbo whistle.
Luckily I was very close to home and was able to pull in when it completely fell off and started dragging on the street. What part of my exhaust is this and what should I do to repair it?
I just finished fixing a ton of stuff on her and now she does this ?
View 24 Replies
I bought a gonzo tune with no lift shift and launch control. I backfire during the launch but not when I no lift shift. It only happens once in a while. Mind you my friend had the same car with same upgrades and his was working better. Both gonzo tuned. What could be the issue?
View 3 Replies
Feel this is a bit stupid, but whatever. I was jacking up the front wheel of the car today on the pinch welds (one part of it got super bent) and while the jack was almost maxed out, my front wheel didn't go anywhere. I must've had almost a foot gap between the wheel and the fender..
Took some pictures of where I jacked, and the suspension/wheel of the car. What it could've been or how I'm supposed to properly lift it so the wheel comes up?
can see the pics here: [URL].....
View 8 Replies
Replacing their stock muffler with a Magnaflow and kept the rest of the exhast system stock? How does it sound? Any performance gains?
View 14 Replies
My lift gate handle has come loose for a second time. First time epoxy was used and that worked really well since the contact was plastic and it Broke. This time it's more loose and afraid if I use epoxy again in same exact spot it won't. Adhere the Same?
View 5 Replies
I have a 1994 Black Ford F150 and i was wondering if i could lift the truck 6 inches only using lift blocks (or any other cheap way to get my truck off the ground)....
View 2 Replies
How hard is it to replace an oil pump on a 1.8T?
View 1 Replies
I am not very familiar with transmissions and clutches, hence I just purchased a used transmission for my jetta 1.8t, i was told that i might as well do the clutch while the transmission is getting done. I just purchased the car two years ago and the guy said that he put a vr6 clutch in. so my question is, what exactly will i need to get for both the transmission and clutch replacement. Like I mentioned, I only have bought the transmission so far.
View 6 Replies
I need to replace my parking brake, it is definitely on its way out.
What I wanted to know is, do I need a cable for each side or is there only one cable?
View 4 Replies
Driving a 2003 GTI
My girlfriends dad and I just recently replaced my pads,rotors, and bled the brakes. He is a journeyman mechanic however he does not see a lot of cars, he mostly works on trains.
Short version is after this replacement I am able to press the peddle to the floor and not lockup or engage the ABS. Before with the old worn brakes this would be no problem to do. We tried bleeding a little more off the brakes to see if there was some air. no bubbles came out. he insists there's lots of brake power. I just find it odd that i can press the pedal to the floor board and not lock up the tires, or feel like i have any real emergency stopping power.
View 6 Replies
I purchased a 2006 Volkswagen Golf TDI from the auction that had blown passenger and drivers airbag. I replaced the dashboard and both airbags, as well as the airbag control module and now the vehicle won't start. It started fine before replacing it.
The only code I got before was the 18996 Prior to this as well as a bunch of airbag ones (obviously due to the air bags)
Now the codes I get are:
Friday,05,December,2014,16:52:12:61795
VCDS Version: Release 14.10.0 (x64)
Address 01: Engine Labels: 038-906-016-BEW.lbl
Control Module Part Number: 038 906 016 AG HW: 028 101 255 3
Component and/or Version: R4 1,9L EDC G000SG 7000
Software Coding: 0150031
[Code] ....
1 Fault Found:
01314 - Engine Control Module
49-10 - No Communications - Intermittent
I cleared all of these codes and 01314 and 17978 are cleared but still won't start so I'm sure its just a matter of time before those codes kick in again. I tried searching these codes and still can't figure it out from all my research. Hopefully I didn't miss connecting something during my dashboard replacement?
View 3 Replies
Just replaced one outer tie rod end on my 2003 GLI yesterday. (ran out of daylight to do other side, now have another problem)...
Everything came apart and went back together fine with really no fighting. Got the alignment close, but will still need one done once I finish up.
Anyways, I am wondering what I possibly could have screwed up, because after a few miles of driving the traction control light (circle with triangle in the middle) came on and now won't go away. I didn't screw with any wires while I was in there. Pretty straight forward job, so I thought. I don't have a VAGCOM but there's no engine codes stored.
View 3 Replies
Currently my gas & temp gauges do not work, so I assume the cluster is shot or needs fixed etc. my question is can I simply replace it with a used one from eBay, or do I need to send this one back to be programmed? I was reading about the immobilizer which I assume the 2003 is subject to as well?
View 1 Replies
I am having a little issue with the ignition in my car. I had the typical no headlights/wipers/heater etc. so I ordered up a new ignition switch and when I went to replace it, the switch fit perfectly and had the correct part number but when I put my key in to try and start the car I couldn't even turn the key but when I put the old switch back in it would turn just fine. Also when I removed the old switch I noticed the red wire going to the switch was slightly burnt right at the terminal.
Here is the basic procedure I did:
-Unhook negative battery cable
-remove lower dash/ center console
-remove switch
-install new switch
Whats this little metal piece? I did not see that when I did mine...
View 10 Replies
Wondering how I would take the A/C pulley off to change the bearing or fix the chirp squeal it is making.
I have spun this pulley by hand and it is the culprit making the noise.
It has an inner pulley and an outer pulley(belt pulley). Both spin freely and are not bound up. Just want the terrible noise to go away.
View 1 Replies
I had taken my engine into the shop and had to have to engine replaced, I would have done it myself and would have saved a bunch of money, however I did not have the time. So I had the same exact engine placed into my MK3 from an old Passet, the only issue I'm having now is the sounding of a misfire on one of the plugs..
Only thing is, all plugs and wires are brand new, so I'm thinking the Coil pack is on it's way out the door. The mechanic said it was the original coil pack so that would make sense. It's a 1997 2.8L 6cyl engine.. I'm looking into purchasing a new pack, and on a website that I had been using a lot lately, only had MK4 coil packs.. Can I replace an MK3 pack with an MK4? Would i have to change the plugs and wires again?
View 3 Replies
Replacing a heater control valve for a 2004 Jetta? My car's vents only blow hot, and I checked the cables and saw that the control arm was disconnected. I tried to put the cylinder piece back in and had some luck, but I can't get it to sit tightly in there and it keeps falling out. Also, it still wont change the temperature coming out of the vents. I assume that something broke on the inside piece that the cylinder connected to.
[URL] ......
Here is an example of what mine kind of looks like, but mine is way more loose.
View 2 Replies
