Golf IV / Jetta IV :: Rough Idling And Die / Dim Light?
Jun 27, 2016
But I have a mk4 gti 1.8t awp and recently it's been going downhill. Right now my only mods are a fmic, Cai, and a 3 in catless dp to a 2.5 in straight pipe. My car recently starting idling very rough and would practically die, the lights would also dim. While casting the idle was very rough too. Then yesterday my car started idling even worse and dying multiple times, plus my turbo stopped boosting and making what I presume to be the "death whine".
I replaced my spark plugs a few days ago and I checked my timing belt and it looked fine. I couldn't find any vacuum leaks either so I'm not sure what would be causing the rough idle? My valve cover gasket leaks and makes my sparks plugs covered in oil but I don't know if that could cause the rough idle. I unplugged my maf and ran it and there was no improvement.
View 4 Replies
Advertisement
I was just at work tonight and went out and started my car for it to warm up (it is -20) and go back inside for about 15 mins, I come out and as I am walking back to my car. I notice tons of exhaust is blowing out from the bank puffing like a steam engine and idling insanely rough with the RPM gauge at about 900 RPM with a EPC code. I immediately shut off the car. Cautiously turn the car back on. Car is idling normally, EPC code is gone, rev it a bit. Everything seems fine.
View 20 Replies
Went out this morning - which was one of the first times we've dropped to freezing since I've had the R32. Car started fine - but idling was rough - almost felt like it was surging. Rev'd it a few times, no change. Meanwhile the tach malfunction light appeared. I turned it off and then restarted. No tach light and it was idling normally.
View 2 Replies
Before I go buy a Bentley manual to dig around, when should my radiator fans kick on. I had the car idling for 10 minutes, no ac or heat on, and my coolant warning light came on, it overheated. It already has a new fan switch in the radiator, and the fuses are good.
View 7 Replies
I was driving along the highway cruising at around 100 km/h when out of nowhere the car started driving a little rough so I look down and the ASR (traction control) light was on. I got off the highway, shut it down and fired it back up. The ASR light was off and car running like normal. When I got home I scanned it and these codes came up:
The catalyst code if from my catless turbo-back exhaust which I plan to fix next month with a tune. Anyway I cleared all codes and continued on my way without any other hiccups. So is my MAF sensor dying/dirty? ECU? N75 valve? Boost leak? I'm making a boost leak tester today just to 100% eliminate that variable, though I'm fairly certain I'm good there.
The car is mostly stock except for a few bolt-ons, all of which I've had installed for thousands of kilometers now. Here is what isn't stock, not including suspension, wheels, etc:
Forge 008 diverter valve
034 Motorsports PVC silicone hose kit
Samco boost hose kit
Forge silicone turbo inlet pipe
Eurojet SMIC
custom built 2.5 stainless, catless turbo back
AEM Dryflo short ram intake
GLI MFA cluster
View 2 Replies
2002 GTI 1.8t (No Tune) 95k
Car becomes harder to start before the problem starts occurring. When the car is started, the idle will rise above what it normally does (750rpm) to 1200-1300rpms and drop back down and raise back up again. Its like its constantly revving itself, this continues the whole time the gas is not being applied. With this comes the EPC light, the Traction Control light and a hardness to the brake pedal (as if the brake booster hose is disconnected or its not getting its vacuum assist, very hard to brake when rpms are at idle). Sometimes im able to boost but most of the time, i am not able to exceed 2lbs of boost. Limp Mode? This has happened before about 5k ago.
I sacked up and got it diagnosed and it turned out to be the Throttle Body, Crankshaft position sensor and the brake booster hose. All at the same time, which is weird. But all those items were replaced by me and the car ran fantastic. until now. This will be the 3rd throttle body put in since the car came off the line. it seems like thats the problem since the brake booster hose is fed vacuum to the throttle body? But i would love second or third opinion before money is spent. If it is the throttle body, what could make this unit go out so systematically and slowly? If it was wiring then you would thing itd kill the part quicker than 5-10k miles. I will post the CEL codes when i can get one to come on.
View 1 Replies
I have APR state I+ and a VWR intake for the last 14 months. My car normally idles at 800 RPM.
In the last few weeks I've noticed it idling a little rough at ~750 RPM.
View 1 Replies
Weird problem on my Passat today. First the engine light came on...followed by rough idling. It smooths out when moving, but rough again when stopped. Noticed that turning ON the AC makes it a little smoother...but when you turn off the AC, resumes the rough idle.
Already made an appt with the dealer tomorrow...but wanted to see if this problem is familiar to other owners. Either way, I will update once the dealer finishes diagnosing the problem.
The car has been perfect up to 30k miles...now 2 problems in the last month.
View 1 Replies
I have a 2006 Dodge Stratus with approximately 104,000 miles on it (most highway) and I'm at my wit's end trying to figure out my rough idling situation. When I was at stop light, I would notice a rougher than normal idling but not to the point where stalling would occur. The timing belt was just replaced a year and a half ago and I thought maybe something was wrong with the alternator??? I took it into the shop and they replaced my engine mounts, replaced spark plugs, and did a fuel injector cleaning....? Well not exactly....now the idling is 10x worse to where my entire steering wheel is shaking when I'm stopped at a stop light! The car itself just sounds rough.
No check engine light is on and the idling isn't nearly as bad as when I park the car....a part of me wants to throw in the towel and say it is what it is, but I just have a feeling that something's just not right.
View 6 Replies
We have a 2001 Jetta 2.0L with 170000 miles. The AC had been getting weaker, but now it only works when the car is idling. Which seems really odd???
Started car, after being parked for a while, and the temp was 73F at the dash vent. I figured it would get colder going down the road, but it got up to 90F at the vent. Returned home and let the car idle for a while and the dash temp went down to 80F. Went for another drive and it immediately raised to 90F.
The compressor clutch was engaged and spinning, but the larger metal line at the firewall didn't seem very cold. The smaller line was warm as expected. I added some R134a, but no change at the lines or in the car. We have had issues with the blend flapper and replaced the broken plastic part. You can hear the flapper slap when you rotate the dial from hot to cool, so it seems like it's working.
Could it be the compressor? I think it was only generating 150psi on the high pressure side during idle, but it would go up to 200-225psi when I revved the motor.
Replaced the valve body solenoids, increased pressure to clutch packs 8 clicks, added pentosin, cleared engine light, and the tranny is working perfectly.
View 5 Replies
Today I went to the gas station and after I gased up and turned the car on my car started idling rough, almost to the point of cutting out. I started out on the road and my check engine light started blinking. After some time it stopped and just stayed on. The whole front end shakes pretty bad when at idle. The car has trouble accelerating till roughly 35-40 mph then seems to ride ok. I'm not very car knowledgeable, but I do take care of my car. I know I need to replace some of my hoses and spark plugs soon, but am worried that it may be more serious.
What I would like to know is: 1. What could possibly cause these issues and 2.
2003 Mazda Protege
View 2 Replies
My gf's 04 gti 1.8t 5spd is having idling issues. Here's the rundown, at idle it sits at 800 rpm but when given a rev it then becomes erratic and fluctuates between 500-1100 rpm. When throttled again lightly it returns to normal 800 rpm idle. The car will try to stall a little bit. Now for the codes and lights. The lights are the traction control light and the check engine light. The codes are p0102 (MAF) and p2181 (coolant system performance). I have recently had a misfire which I took care of with 4 new coil packs. I kept the 3 good ones I took out. I have to change the plugs still but don't think it's an issue. Has new clutch and sits at 148,852 miles.
View 5 Replies
Every time my car is idling I get this weird fluctuation of rpm. What it might be. [URL] .....
View 7 Replies
I have a Golf GTI IV 1.8T Tiptronic and having this problem when the car is Idling i can feel the engine vibrations trough the seat and are anything but soft, especially if the trany is neutral and less if leave it in D.
I've changed the dog bone recently, wich was very bad, but the vibrations didn't smooth they remain the same but the driving improved, so the dog did replacement was good.
The next step would change the engine mounts, but they look goof and I don't want to start change parts just in case. Where I live car parts aren't cheap and some times new ones are just crap.
View 1 Replies
My car is idling rough and the Service Engine light blinks on/off continuously. I ran the codes and they are P0301, P0401 and P1258. What this could be? I changed the plugs, wires and ignition coils about a year ago. Catalytic converter was replaced around the same time but the O2 sensors hasn't been changed. Could that be the cause?
View 1 Replies
2001 with the 3.1 6cyl. First thing that started this nightmare is I was noticing a bit of a hiccup after driving for a couple miles. We've only had the car a few months and not sure what maintenance was done so we thought maybe it needed a tune up. Before I got the parts the check engine light came on so I went to parts store to get it read, it was P0302.
Did the wires and plugs and it got worse, the code wasn't p0302 now its just p0300. But after the plugs it also started idling really rough and would be slow to shift. Once it tacked up high and wasn't speeding up. That was only once tho. Also now it has no power its like driving a 2cyl ...
Anyway we decided since the first code said 2 we replaced coil 2, no luck..ok, fuel filter and fuel injector 2, no luck. Also has cleaned various things Im not sure of the technical name for..sensors and air filters and other things.
None of this has worked the car still idles very bad and doesn't have the power it should have. Also cleaned things on fuel rail(?). He is in the process of replacing the crank sensor as someone said if it was all the way bad it would throw a different code but it may just be faulty.
View 10 Replies
I have a 2004 Jetta w/ the 2.0 engine, auto transmission. Lately it has developed a very gassy smell when idling. Could be all the time I guess, but I only ever notice it when idling. It seems more noticeable on the passenger side of the car, or maybe my wife just has a better sense of smell than I do since she noticed it before I did.
The car seems to run fine, about the same as it always has. The idle is slightly rough, but it has been like that ever since I got the car. I got it with about 110,000 miles on it and had the timing belt and water pump replaced as soon as I got it. Mileage now is about 130,000. No info on the maintenance history of the car, but when I had the timing belt changed they said it looked like it was probably the original one.
The check engine light has never come on. I think I'm due for some new spark plugs so I was going to be replacing them soon anyways. Not sure what to check out here that might be causing this?
View 3 Replies
When I'm idling and I rev the engine to exactly 1200 rpm i can feel an extra vibration coming from the engine. If i hold it at this rpm it will continue on. now this is not a violent vibration but more so of a buzz i can feel that travels to my steering wheel as well. what could it be ?
Another question is when i travel up my driveway and i hit the sloped curb at a angle i can hear a specific "clunk" sound coming from around the drivers foot well area what could this be? perhaps my axle going bad? I also heard it when I was reversing out of my parking space while turning.
I am new to this car and trying to make sure I'm doing everything i can to put it into good shape.
View 3 Replies
So I recently swapped my 2.8l 12v vr6 for the same engine because mine blew up, everything went good and the car runs great but there is a faint kind of rattling sound coming from the top of my motor, when its idling it will be a constant faint rattle. It gets worse as i accelerate between 3 to 4.5 rpms but then stops making the noise when i really start cooking so Idk if I just can't hear it or what. I've tried looking it up but i can't seem to find a video that has the same problems as my car. My father told me it could be my rockers or valves and others have told me it could be my timing chain or guides. I would love to just take it to vw to get it diagnosed but I don't have the money. I will try and upload a video of the sound ....
View 7 Replies
I have a MK4 Golf 2003 1.9Tdi PD100 , the problem is that the engine seems to miss when idling , so the question really is how can I tell which cylinder is missing , it seems to do it every 10 seconds or so and the engine shakes slightly at the time as if it were missing ! .
I suppose it would be easier if the cylinder was missing all the time , then maybe I could crack open a line at a time ! , but can you do that on a PD engine !
View 1 Replies
I'm running into a brick wall trying to get my GTI to start. This post is my last-ditch effort before just towing it to a shop.
A little over a week ago, the car just died while idling outside a buddy's house. Prior to dying, it had been having some sputtering starts and had been dying while driving as well (engine cut outs) for about a month, but it had always started right back up strong after cutting out.
First I tried replacing the crank position/engine speed sensor. No dice, still not starting. I had new spark plugs in the toolbox so I popped them in, still nothing. Then I realized that my spark plugs were totally dry when I changed them. I pulled the hose off the fuel rail, tried to start the car, no fuel. I had a more mechanically inclined friend come out with a multimeter and he checked my fuel pump and relay. He tells me the relay is good, but the pump must be fried because it's getting power but not pumping (I'm not certain of this as I didn't physically lay eyes on the multimeter when he told me this). The next day, I replaced the fuel pump and the fuel pump relay just to be safe. The car started! I thought I had it all figured out. I drove the car for two days and then, last night, it refused to start again. This morning, pissed off, I went back and was ready to tow it but it started right back up again on the first try. I drove it home, but then later when I went out to go grab a burrito it wouldn't start again. It cranks and cranks but just won't catch.
Pertinent information:
- I do have a CEL. Don't remember the exact code it's throwing but it's something like "Engine distributor circuit, no signal." The code cleared after installing a new fuel pump, but the CEL is back now. Could be a new code, though as I don't have a scanner.
- No other nasty dash indicators are on.
- With the new fuel pump, even when it was working normally, I never heard the usual "priming noise" you get when opening the driver's door. This is strange to me as I used to hear it all the time.
- The car cranks normally but I think it just isn't getting fuel, even with a brand new pump, plugs and relay.
- About a year and a half ago, the coil pack was replaced under the recall campaign.
After all these new parts, I'm thinking electrical. A ground short or something. But I've seen that for some people it was the ignition switch, or the IMMO, or the fuel injectors, etc....
View 2 Replies
