Golf IV R32 :: Loud Clunk When Banging Into 2nd Gear
Jul 27, 2011
Only when I'm banging through gears into 2nd my motor I think, makes a loud clunk. I checked the motor mounts an they were tight. What else could it be?
View 10 Replies
Jul 27, 2011
Advertisement
Golf IV / Jetta IV :: Loud Banging Sound When Go Over Bumps
So I replaced my rear coilovers on my gli assuming the driver side was broken because when over bumps it would make a loud banging sound as if it was bottoming out but after replacing them i have the same problem.
View 1 RepliesGolf IV R32 :: Loud / Tinny-Sounding Banging Noise From Rear Of Car
Went out to run some errands this morning, and was alarmed to hear a loud, tinny-sounding banging noise from the rear of the car. It would occur on every bump. little or big; every time I braked; every time I started up from a stop; after each shift to a higher gear; and every time I turned a corner.
I was getting really concerned, as I had never heard a noise quite like this on any car, ever before. When I got home, I pulled the floor jack out of the garage, then went to the trunk to get my torque wrench with the wheel bolt socket on it.
When I opened the trunk, this is what I saw: ...
Golf IV / Jetta IV :: Loud Banging Coming From Engine Bay - Blown Headgasket?
So I was driving home from work in my 2000 Jetta 2.0, which has 115k miles on it. Its a 5 speed and I love the car, even though its kind of a beater. Anyway, coming off the highway and reducing speed, I hear a loud banging coming from the engine bay. It sounds like a car would if a spark plug were blown out of the block.
There is definitely a loss of power and the motor is running rough. The check engine light is flashing at me constantly. I pull off the highway and pop the hood. No fluid loss, no obvious smoke coming from anywhere. I start feeling around the engine bay and I feel high pressure air (exhaust?) being expelled from under the valve cover.
So what could have broken? Cracked head? blown headgasket? some other thing I haven't thought of? Its obvious that exhaust gas is leaking from a cylinder into the valve cover.
Toyota - Dolphin :: 1977 - Loud Clunk When Shifting Into Reverse Gear
Sometimes when putting the vehicle into first it's almost impossible to get it to go into gear. Sometimes it's super smooth. Also when putting into reverse we hear a loud clunk. That one is most of the time but sometimes it goes in smooth. I was doing some looking around at the pedals because I think I am going to have to replace my master cylinder and noticed that on the inside of the vehicle where the clutch master cylinder comes into the vehicle it's leaking black fluid. Does that automatically mean my clutch master cylinder needs to be changed? Could this be the cause of it being difficult to shift because the clutch isn't fully disengaging?
View 11 RepliesFord Super Duty (1999-2016) :: Loud Clunk Locking Into 3rd As The Gear Engaged
Was pulling passat home 50 miles round trip this saturday and downshifted into 3rd. As the gear engaged it let out a loud clunk locking into 3rd gear. was able to find neutral after a day but slammed into gear just idling. Can find neutral on pattern but not actually get there....also drags right rear tire upon disengaging clutch.
1999&half psd zf6 1 ton single....
Ford Super Duty (1999-2016) :: Clutch Slipping - Harsh Shifting - Loud Clunk Noise Into Gear 2 Then 1
New truck 11000kms ago thats done medium amount of work but nothing heavy or sustained for long periods of time. I get the feeling of clutches slipping especially when truck is cold but also when normal temps. Doesnt make any weird noises or anything. I can really notice the difference in torque if in manual mode being much better, but still not perfect if i stomp on the gas pedal and go through the gears in manual mode will still slip. Also is really harsh shift if i come to a halt in 3rd manual mode with the brake pedal depressed push minus button the truck makes very loud clunk noise into gear 2 then 1. Took it to ford they couldnt find anything ? Thinking of trying another dealer.
View 2 RepliesGolf IV / Jetta IV :: 2002 - Loud Clunk When Going Over Bump
I've had my 2002 Golf GLS for about a year now. It has 127k on it and I absolutely love it! Saves a lot on fuel driving 100 miles a day for work compared to my Ram 2500 diesel!
Anyway, lately ive been hearing what I can best describe as a "clunk" or maybe the sound of metal hitting metal when I go over a bump. From what I can tell it sounds like its coming from the front passenger side. Maybe the rubber grommit on the strut tower is gone? I havent really checked it out becasue I havent had much time on my hands lately.
Also, ever since I have had the car the engine seems to run louder than what I expected for a VW. It has the 2.0 engine in it. Is this normal? It kinda hard to explain how its running loud but when its at idle and I have the hood up it just doesnt seem as quiet as I thought a VW motor would sound.
Golf IV R32 :: Transmission - Loud Clunk When Releasing Clutch Pedal
My R has been giving me some trouble lately. First I had some issues, I thought were clutch related.
-A loud clunk when releasing clutch pedal (only when engine running) and sometimes when depressing it too.
-Randomly changing clutch biting point when driving hard. So e.g. when revving through 1st and 2nd gear the clutch would bite much lower than usual. (This was so weird.)
-Whistling sound when changing from 1st to 2nd gear.
Replaced the clutch, flywheel, pressure plate and the TOB and bled the system several times. Also new solid DLI motor mounts and new oem dogbone mount.
There was some side-to-side play on input shaft that I was told is not a big deal. Also this gearbox has always been much louder than other cars Ive driven.
Now that weird changing clutch biting point is gone but other issues are still there. And now, because of the lightweight smf and the motor mounts the gears shatter and whine so much more on low revs and during engine braking. I know 02m s tend to do that but its so loud I am a bit worried.
Golf VI R :: Loud Clunk Coming From The Front Shock Area
So after a few months of having these springs on the car I noticed that as of recently there is a loud CLUNK coming from the front shock area. This specifically occurs in the morning while backing up out of the driveway, after the car has been sitting for a long time. This happens at low speed as soon as i turn the wheel to align with the street. To make matters worst, there seems to be a more persistent noise coming from the rear whenever i go over any sort of rough surface, almost as if something is loose . I took it to my local VW to see if they could replicate the noises and they did. I did not mention I had springs on the car (VWR), should I have ? What could be causing these issues?
View 12 RepliesElantra HD (2006-10) :: 2009 - Front End Loud Banging Noise
I am getting frustrated with a loud banging noise in the front end of my Elantra. It happens when I hit bumps or dips in the road. I have replaced struts, bearings and mounts, sway bar links, control arm bushings and nothing will fix it. The ball joints and tie rods are tight.
View 7 RepliesGolf IV R32 :: Shifting Noise Too Loud From Gear To Gear?
Shifter seem like it is way too loud going from gear to gear? Just holding in the clutch and rowing from gear to gear...seems way too loud, Seriously sounds like shifting gears in my old 5.0 mustang.
View 1 RepliesToyota - Camry :: Loud Banging / Grinding Noise Only During Heavy Downpour Rains
I have a 2000 Toyota Camry LE with 106K miles. It?s getting a little clunky but works perfectly. I do regular maintenance like oil changes every 3 or 4 months, breaks, tires. Last year one day during very have down pour rain I noticed something banging/hitting under the seats while driving in this heavy rain & car losing power (slowing down). Something (I am guessing the exhaust pipe? hitting the body. The more gas I gave to gain speed the violent the banging. I slowed down to almost 15MPH but never stop & the car started to work normal. It happened 3 or 4 times before I got home. I check all fluids etc? All normal. Drove later in sunny, cloudy & even in light rain the car runs perfectly fine. Then it happened again in heavy rain.
I told my car mechanic & he checked all even tightened the main belts (not timing belt). No change. Now it?s so predictable when ever its rains heavy & even slushy snow/rain. Lately it started to not only lose power but sometime instead of banging I hear grinding noise when pressing the gas paddle. Some time banging followed by grinding but every time after slowing down the car recoups power and I drive normally. It never ever happens in dry day. My wife who drives ?Buick Century 2004? thinks my car is dyeing and should buy a new. When I describe this situation to any mechanic they points to transmission & want to perform brain surgery to diagnose.
Ford - Explorer :: 1997 - Loud Banging Coming From Front When Turn Left Or Right
1997 Limited SOHC auto.
I just replaced the transmission with a known good one from my XLT but the reverse doesn't work now and there is a loud banging coming from the front when I turn left or right.
It feels like the tyres are slipping on the road, like axle wind up. This happens in auto and 4wd high. What the banging is?
Ford - Explorer :: 1998 - Loud Banging Noise When Driving Coming From The Rear
My 1998 Explorer is making a terrible banging noise when driving. It appears to come from the rear. It only occurs when i step on the gas, gives a bang and the car shudders lightly. The bang can be gone for 10 - 30 seconds, and all of a sudden appear again. If I step hard on the gas, it will make a bang! bang! bang! noise.. If let my foot off the gas, it rolls quitely without any noise.
I have greased the slip yoke, inspected the U-joints, checked the rear calipers, opened the rear axle/differential plate - no metal parts or excessive wear were observed.. The transmission runs smoothly, there are no other noises apart from the bang. It is as if someone is hitting the car with a hammer from underneath...
Ford - Mountaineer :: 2004 - Loud Banging Noise Coming From The Engine Compartment
I have an 04 mountaineer and when i shut it of i get a loud banging noise from it. Its sounds like its coming from the engine compartment. The truck itself runs great and I didn't see any exhaust leaks. It has 70,000 on it.
View 2 RepliesGolf IV / Jetta IV :: 2005 - Clunk Sound When Going Into Gear
So I have a 05 mk4 golf 2.0 automatic. Ive noticed that when i take it from park to drive the car shakes and makes a huge clunk sound like I just got hit by something. Turns out it was a motor mount, I think they call it the dog bone cause its attached to the body & engine of the car. So it was replaced but the car still does it. But not as hard & not as much. Before when I revved the car it would kind of shake and dance. Since the replacement it parks still when I rev it. But that noise is still there. Someone told me it could be another mount or the torque converter.
View 2 RepliesGolf V R32 :: Clunk Into 6th Gear On Light Throttle And D Mode
Posting this because I saw many other owners with the same problem. Basically after warming up DSG every time clunk into 6th gear on light throttle and D mode, speed around 50kmh rpm around 1400.
You can hear it and feel it on pedal a little. Sometimes is not so harsh sometimes its big clunk. Of course it did on manual mode too if you try shift in the same position.
Original thread here: [URL] ....
Its well known that DSG D mode is set to shift early for better fuel economy but this is not good and really annoying.
I have same problem and its not mechatronic related mine was replaced do to jerkiness on 2 gear and clunking into 6th it is the same.
So I know that fix could be DSG tune/reprogram that many company offer. D mode is optimized and shifting moved to "normal" rpms. A lot of you don't have even problem because your its already flashed with combo etc.
But in my area no body offer DSG tune and i really don't know how to solve this problem... don't want to replace whole gearbox because in all other ways works ok.
I have 2012 MU with i think lastest SW and it didnt change anything on this.
Golf VI R :: Drivetrain Clunk / Pop When Engaging Gear And Shifting 1st - 2nd
I have been reluctant to post another clunking thread because it's nearly impossible to accurately describe what is happening. But I have reached by breaking point and I wanted a few opinions before I take it into the dealer. I am still under powertrain warranty, but I want to be confident I am not wasting mine and the dealers time if I am just missing something easy. I also know dealers don't always take clunks seriously so I want to pinpoint it first.
Symptoms : Car has 50k miles. I am the original owner.
From a stop, when getting the car rolling moderately aggressively there is a clunk/pop noise from the car. I can slightly feel it in the pedals and it is fairly loud. Almost like a distant hammer and nail pounding. It's a single clunk, with sometimes a double "pop pop". It's noticeable even with the radio turned up a little. If you are smooth on the throttle it doesn't make the noise. It seems random, like something is hitting something which only happens under certain weight shifts.
It sounds like it's from the rear and the front. It seems to switch. But honestly I am not confident either way. Where it is. It is silent on turns, bumps, speed bumps, driveway, etc. I don't think it's the suspension. It is not a clicking/tapping, only a single clunk or knock.
It also happens in 1st/2nd in stop and go traffic. If you leave it in 1st and the traffic is moving from say 8-15mph where you don't need to use the clutch it will clunk during on/off throttle. Anything above ~30mph I haven't been able to replicate the noise with on/off throttle.
It also does it if I downshift when coming to a stop and don't rev match. Say you are slowing down and you go from 4th, 3rd, then 2nd, let the clutch out and it rev matches up to ~3,000rpm which causes the weight to shift forward....clunk! It is not easy to replicate which is another reason I am slow to bring it to the dealer until I pinpoint it.
Things I have tried:
- Subframe bolt torque check. Installed ECS spacer/bolt kit anyway.
- Sway bar links are tight, or at least they didn't budge at all.
- Adjusted the rear hatch a million different ways as it was making a similar noise earlier.
- Spare tire tightened, tools removed
- Rear seats up/down/mix/seat belts fastened, etc.
I was only able to locate one motor mount? Where they are. Seems fine. Dogbone seems fine, again hard to tell.
Suspect:
I have VWR springs, but I am 90% sure this started happening right before I had them installed. I did the rears myself, a well known shop did the front. I noticed the noise maybe 2k before the springs were installed.
Clutch linkage somewhere - I had issues with my transmission (early build). The clutch was replaced at 7k. I've always had a very loud flywheel and a grinding feeling in the pedal. Maybe the shifter linkage is hitting something? I have little experience with VW's so I am still learning and don't know what to check.
My rear harmonic balancer is cracking like everyone else. I have no vibrations yet and I don't see how it could be causing a clunk in the current state. Maybe a motor mount is bad that I cant see? It feels like something is loose in the drivetrain.
Ford Super Duty (1999-2016) :: 2000 F250 - Loud Banging Noise When Going Over Bumps
I have a 2000 F250 2wd 6spd with a loud banging noise that has been vexing me for quite sometime now. The bang happens when I go over bumps (even small ones like road reflectors) while driving. I don't think it is suspension related since all the ball joints, front/rear swaybar and endlink bushings have been replaced fairly recently. All the springs and bushings also look okay.
The noise seems to come from the rear, and I notice that if I let off the gas when I go over a bump, it does not make a sound. Conversely, if I am accelerating aggressively and hit a bump, the sound is much louder. Also, if I step on the clutch while keeping my foot steady on the gas, it makes a bang. Jumping up and down in the bed while the truck is parked does not recreate the sound. I have already greased the driveshaft spline joint so I'm thinking the sound might be differential or transmission related. What it could be?
Passat (B5) :: Slipping (hesitation) During Upshift And Occasionally Banging Into Gear During Downshift
Took my car to the dealer for it's 80K service and asked them to check the tranny because it's been slipping (hesitation) during upshift and occasionally banging into gear during downshift. I figured they would suggest the BG tranny fluid flush but got a call from the service advisor saying they found the fluid to smell burnt and it was black. 1999Pazzat V6...
View 8 Replies