We have a 2001 Passat with a 1.8T engine. There is a small vacuum hose at the front right fo the engine attached to the manifold that is cracked where it attaches and leaking. I'm fairly certain that this is causing the MIL light to come on. The clamps that hold the hose on look to be put on with some sort of custom VW tool. I'm going to replace this hose myself. What to use to reattach the new hose?
View 17 RepliesI have a 2000 B5 . It has minor damage front and rear (cosmetic only). Also, the check engine light stays on due to a vacuum leak somewhere between the MAF and the intake manifold. It would need a full paint job at some point after the body work was completed.
View 3 RepliesI have a Passat 1.8t b5.5 with 150hp
Some months ago I chipped it and it drives very good and I also changed the diverter valve to a 710N.
But now it is fast, but sometimes it just feels like it doesn't hold boost as it should. and I hear a very loud psss sound just like a BOV when I shift. Could it be the 710N which has been broken? Or is it a vacuum line to the DV that has a leak?
I have a 2000 1.8L that's great. I have seen a reference to Vacuum leak diagnosis. I have a check engine light on and it has been for a while. the car still runs well and gets fine gas mileage. Coed is 1136. Is there a specific hose I should check?
View 7 RepliesI have just replaced my vacuum lines after find a hole in the hose going the the vacuum reservoir. I have also recently replace the pcv hose. This seems to have created increased vacuum pressure and I am now hearing a hissing coming from the back center part of the engine.
Pulling codes P1411, P1423, P1138
Regarding photo - The area the hissing appears to come from is located in the rectangle area, more or less.
2.8 atq B5 Variant
I have a 2000 Passat 1.8T. When I start it up in the morning I hear a loud obnoxious noise like a vacuum leak from the engine compartment. It lasts for about 1.5 minutes then runs normally. After about a minute it starts up again and only last for about 7 seconds...ish. When I drive it afterwards, less that a half block or so, the CEL light goes on after 1 beep. Also, at that time I get a messages from the instrument panel that says "Emissions Workshop 1". I've read that it could be a simple damaged vacuum hose to the secondary air pump. Definitely a huge price difference to repair.
This morning is was colder outside than usual and the dash kept beeping and flashing the "Emissions Workshop 1" code intermittently.
I have a check engine light on the car and in the past it has been bad gas or a vacuum leak. Dealer says on toyota that is not possible.
View 3 RepliesI recently had a Jasper rebuilt engine installed in my Ford E150. Since than my check engine light keeps coming on and the computer is saying my cas air mix is "lean". The instaler says i need a new fuel pump.Another mechanic says it is more likely a vacuum problem.I know it's possible that the fuel pump is bad bur since this has just started since the install, I don't believe it can be the fuel pump unless it's just one hell of a coincidence.
View 6 Replies2002 F250 SD 4X4 5.4L. 4.5 inch pro comp lift tire size 305/75/R16. K&N cold air set up. 208,000kms
I know the truck does horrible on gas but lately is been getting worse, maybe I am getting 350km to a tank. Mixed highway city driving. Sounds like I might have a vacuum leak somewhere but I have no engine light. I've had the truck since last year and put about 10,000km. on it done regular oil changes .. brake maintenance no motor work so far.
I need to clean the TB and MAF/MAP. Where are they on engine and what is the best way to clean them? Also, what is the best technique to detect vacuum leak?
View 13 RepliesI suspected I had a vacuum leak somewhere, was told it wasn't likely. Just installed a tune in the evening drove it 15 miles was pretty sure I had one.
Installed Forge DV the next morning it was evident I had one by the sound the DV was Making. I checked the car head to toe and found two lines had broken apart. I replaced them will silicone lines and it appeared to be fixed.
Drove it 5 miles and the 'turkey sound' came back. (This is the sound that I originally heard and confirmed I had a vacuum leak somewhere)
I searched all over there car, had a second set of eyes that was mechanically inclined and we found nothing obviously causing a problem. We ended up just taking off the Forge DV and testing it by hand it held up and re installing it and securing it.
Strange enough that fixed the problem (no other hoses were tampered with while we were inspecting)
Drove the car home about 15 miles and stopped in a drive through. At some point while sitting something happened. Cause when I left the drive through then I noticed the car seemed to be lacking at low end, turned down the music and I could hear the turkey call. I left the car alone for the night. Thought maybe heat jas a factor in this. Drove it this morning and it was just how I left it. I inspected the hoses and found no change. I took the DV off and inspected then re installed. I noticed the turkey call was not as predominant but still completely present.
My ford's 4x4 will work if I manually lock in the hubs. If i use the auto option it will not engage. I can feel the rear end diff lock when I put it in 4-low so I know the switch is working. I think it is a vacuum actuated system. How to find the leak or diagnose the problem?
View 7 Repliesi have a 04 gli torando red i spike at 12psi and hold at 10psi. the last three days im only getting 5 psi i fixed some vacuum leaks and it went back to 10psi then today back to 5psi dont know if its chipped it does have fmic and air intake and bov...
View 8 RepliesI know all about vacuum leaks and such causing this problem, and I tend to think that is my problem. But isn't the temp change dial also vacuum controlled (in my case of an 06 f250 6.0) by that valve near the oil fill tube on the passenger side? I ask because, while I am stuck on defrost i can change the temp of the air that comes out still, telling me there is enough vacuum in the system to at least control that.
I also know everyone talks about checking the ESOF system for cracked lines/leaks, but this shouldn't come in to play unless I have 4WD selected or if the EFOF solenoid is bad, right? I just got done tearing the top end of this engine apart, twice, for oil temp problems and am about done working on this POS!!!
Today I was checking up on the engine and noticed a weird "sucking" noise coming next to the air filter box.
I've researched a bit and it seems like I might have a vacuum leak? I have attached a video on the noise, I recorded on the phone so you might need to turn up the volume a bit higher to hear the noise (vertical recording, the noise starts at about 38 secs)...
[URL] ....
Just bought my volvo several days ago. It was throwing check engine codes so I had it scanned and it came down to a vacuum leak. I found the spot where it was leaking which was a little piece to the left and slightly behind the exhaust manifold, slightly behind and beneath the thermostat housing. It went from a hard plastic vacuum line, to a 1.5 inch rubber vacuum line which plugged into a nipple on the exhaust manifold or something behind the manifold. the rubber section had 3 large holes in it, so i replaced it with more rubber vacuum line. same length and same inner diameter.
What I did notice when I replaced it was that it was too large for the plastic line, slid on way too easy, but i had to fight it onto the nipple. The check engine codes went away for 2 days(I drove about 150 miles over that time) but today, the check engine light came back on, went to auto zone, had them scan it, came back with vacuum leak. So when I got home, I popped the hood, sprayed some carb cleaner by the replacement vacuum job I did, and sure enough the idle changed. What the proper replacement hose is for that area?
[URL] ....
Recently bought a MKV R32. Already had a magnaflow cbe, k&n panel filter, and some emissions stuff taken out from under the hood. not sure if it has been flashed, waiting to get a vagcom. think it is pretty stock other than that. My problem is about 2 weeks after I got it, I started to notice an exhaust leak or vacuum leak or both at higher RPMs, like above 3 or 4k it starts. The exhaust has a nice deep rumble in normal driving but when the leak noises start that is all you hear, the exhaust note disappears completely. I have tightened the clamps on the cbe and still does it. Not sure what to look for.
View 3 RepliesI have a vacuum leak on the driver side seal on the changeover rod in the intake manifold. It was replaced recently at the dealer and now has another hole in it. I was told this is caused by oil in the lines and my pcv valve is bad.
View 1 RepliesI have a 2005 Ford focus. I haven't even had it 8,000 miles. THREE times it has overheated, and I've had to replace over a gallon of coolant. The first two times, the cause was a leaky 'vacuum' cap. The third time it was a different cap that was leaking. This radiator has two (that I know of) unused ports on it. A 3/8" one on the top left, and a 5/8" one on the bottom left. They are capped off with little rubber vacuum caps, which are quite simple to replace. But, these things don't last long before they start to weather and crack and leak. I just replaced them after 2,000 miles (before they started to leak), and they're already cracked. But oddly, only on the OUTSIDE. Inside they're still smooth and unbroken.
I've asked for advice at auto parts stores, mechanics, and even at a radiator shop. They all say they've never heard anything like this before?! I just got some silicone vacuum caps which are specifically rated for high temps, but they're so thin I'm not sure I wanna install them.
Car: 2011 VW GTI MkVI
Mileage: 79k
Configuration: Stock
Warranty/Coverage: None
So I started my car last Monday and the check engine light was on. Didn't think much of it because the car ran fine and there were no immediate symptoms. I was busy with work this week, but noticed some changes in the car's performance over time so I waited till Thursday to have it scanned at AutoZone, which threw the following codes:
P 300 Definition: Random Engine Misfire
Explanation: Lean air/fuel ratio
Probable Cause: Ignition system misfire condition, Fuel injector fault, Engine mechanical condition
P 302 Definition: Cylinder 2 Misfire
Explanation: Vacuum leak on engine
Probable Cause: Ignition system misfire condition, Fuel injector fault, Engine mechanical condition
P 303 Definition: Cylinder 3 Misfire
Explanation: Vacuum leak on engine
Probable Cause: Ignition system misfire condition, Fuel injector fault, Engine mechanical condition
Prior to making any purchases I noticed that I started losing some pickup, primarily in lower gears between 2-3k RPM's. Praying that it was somehow just the coils/plugs I bought the R8 pack for both and replaced them this evening. Engine starts up and continues to misfire. I have not had a chance to have it scanned but it would appear it isn't the plugs or coils.
When the plugs were removed, there was an 'oily' substance on the threads, which also seemed like it could have been burnt off fuel or oil pushed up from the cylinder. Also 2 of the plugs seemed looser than the others and didn't feel properly sealed. New R8 install included proper plugs for STOCK application, as I do not run any tuning, and i installed with the appropriate plug grease added lightly to the threads.
I took the car for a spin with the R8 coils/plugs installed to compare it to how the car was doing prior the install. Car misfires and seems fine (relatively) at idle and revving to 2-3k rpm yields NO change. It is almost unable to accelerate up a hill, or go past 30 MPH without the car shaking and any gear higher than 3rd seems not drivable. I feel these are my potential diagnoses before i bring it somewhere and have it looked at.
In Order of Most Likely:
1) Fuel Injectors
2) Air Intake
3) High Pressure Fuel Pump
4) Electronic Leads for the Coils
5) Battery Needs Changed
6) Chain Tensioner Failure
7) Coils and Sparks are all Bad, and I am an idiot
I would prefer to do this work myself and can afford the parts. I just didn't want to be fooling around all month without a mode of transportation to get to and from work.
Brake pedal whistles and is hard to push. Only happens intermittently. Mechanic wants to put new brake booster on. This would be 3rd brake booster in 9mos. It's gotta be something else. What does the vacuum hose connect to from the check valve; where on the intake manifold? If no PVC valve...then what else? Truck runs fine...no fast idle or rough idle and no hesitation.
View 4 Replies