Ford - Escape :: 2001 - Low Power / Missing And Shaking When Going Up An Incline
Oct 31, 2013
2001 Ford Escape or later and having problems with missing, low power and shaking when going up an incline. I have had problems with my escape for the last two years missing and missing and more missing. Have replaced Coil packs and spark plugs several of them. Well back in June I let the Mechanic have it for almost 3 months. All 6 coil packs were changed, spark plugs included, all vacuum hoses, belts, water pump, front CAT already had new radiator replaced last year. Had two broken wires leading from the PCM to the fuel injectors 1 and 5, he re did the wiring harness there and checked the fuel injectors.
After all done that could be done, I took my car back and it was purring like a kitten, on a flat surface that is............after driving it for several days, headed to another city and had several small inclines to go up, not bad ones, and between 45 and 50 mph, my escape started to shake, miss, and make noise, not a loud noise, but enough to get my attention, and the check engine light started going on and off. Today I took it back to my mechanic, he went on a test drive with me, (me driving) and it duplicated the problem. Went back to his shop, put the code machine on it, and no codes, I asked him if he had serviced my transmission like I asked, and he checked with his other mechanics and they said no, that the transmission fluid seemed okay, figured it didn't need it. Well guess what it did. So if ya'll are till having problems after you have replaced the coil packs, check for electrical issue around fuel injectors, and your front CAT, mine was full of fuel, then make sure you service the transmission, and you'll have the best little ride ever!!!
View 3 Replies
Advertisement
So I have just over 14k on my 2015....... I love the truck but have had a few small issues. I had a water leak coming in from the roof that would leak through the grab handle. Nothing major dealer replaced one clearance light seal and they said the windshield needs to be re sealed.
Then I had a god awful irritating squeak in the dash..... It only does it late In the day when it's been hot. The dealer said it was a loose air bag. I have had the truck back a week and it's doing it again.
Those are little issues that will get resolved...... I hate having problems with a brand new vehicle but I understand it happens and that's what warranty is for.
I also reported a bad shake to the dealer...... The truck will shake very violently and have a very loud "diesel" sound. It's very specific at when it occurs. It has only done 4 times in the past 6 weeks including today. The odd thing is the 4 times it has done it has been the same time of day in the exact same spot on the exact same road!!!!
Basically I leave my office sit in some traffic and by the time I get to the parkway it has been35 minutes or so. Only happens in 6th at 60 which is roughly 1,400rpm a slight load due to a small incline and it shakes real bad! The typical "diesel" sound you get when under a load is very pronounced almost to a knock. It will continue to do this as you slowly increase throttle until it down shifts and then goes away. I also caught it doing it and I manually shifted to 5th and it went away.
Because of the rpm at which it happens with slight load only doing it in 6th I lean to a Trans issue and more so a converter problem. It feels like converter shutter. I just don't understand the engine sound.
I gave very descriptive info to the dealer..... Several techs drove it and could not duplicate. I just picked the truck back up last Thursday and the dash squeak is back and the shake happened yesterday and again today. So I am a bit irritated to say the least.
I really hate the fact that I know there is a problem but I also understand if a tech can't duplicate it he can't diagnose it. However today I did get a video of it with my phone so they will know I'm not making this crap up!
View 8 Replies
I have a 2001 Escape I bought new so many years ago. It only has 90k miles. The other day I drove it to work running fine. It rained REALLY hard that day and when I came out to go home it would barely start, missing really bad. Limped it home and into my garage where I examined it for water under the hood. Nothing. Started pulling things apart, nothing on the engine, around the coils, in the spark plug conduits, etc., dry as a bone. Let it sit for a couple of days and no change. Replaced the coils just for grins. Drained the fuel from the injector assy, looking for water. Nada. Verified spark, fuel, compression. Still, very difficult to start and when it does it's only running on cyls 1,2 & 3 because I can disconnect the coils on 4,5,6 and it makes no difference.
View 6 Replies
Car misses horrible at times at idle and lower RPM's, shakes the whole car. MPG around 32. Runs better when car is fully warmed up. PO171 and PO 300, 301 and 304 codes come up.
Here's what I've done so far to try to correct the problem:
Cleaned mass air flow sensor. No change.
Replaced mass air flow sensor. No change.
Replaced plugs and ignitors (coils). No change.
Replaced PCV valve. No change.
Replaced upstream O2 sensor. Same codes come up but MPG increased to 37.
Replaced throttle body. No change.
Car does not miss when accelerating hard. Sometimes runs perfect at idle and lower rpm's, but mpg is way low as it used to be in the 50's or higher. Car idles perfect in neutral. Always runs perfect the first 3-4 seconds when you first start it, then starts shaking. If I put my finger in the throttle body when it's running poorly, apparently disrupting the air flow a bit, the idle smooths to perfect.
I have an extra computer, although I don't know if you have to program the key for it to work. I don't suspect this is the problem anyway. I haven't changed the fuel injectors. I can't hear a vacuum leak.
View 8 Replies
Fuel mileage is terrible also but the truck really has no power. Running down the highway it kicks down just to pull a small incline. Check engine light is not on and there is no hessitation. The truck has 105k on it and i have put only 5k of those miles on. I did pull a couple plugs and they are autolites so plugs must have been changed at some point. Does this sound like a coil problem?
View 5 Replies
2004 Hyundai Santa Fe 3.5L V6. I am experiencing an issue of losing power as I travel up an incline and it doesn't matter how much I depress the gas pedal. The codes that I am receiving are P0101, P0174, and P0171. After reviewing the codes and doing some research I'm thinking it is either the mass air flow sensor or the fuel pump, which can tend to fail in vehicles 10 yrs or older depending on vehicle mate Nance (i.e. constantly running the tank down to almost empty).
View 6 Replies
2007 Rabbit shakes quite hard when i accelerate mainly on any type of incline and only between 35-60 mph. When i take it to the shop they cant find a problem.
View 3 Replies
2001 Excursion 7.3 started missing the other night. Great loss of power, but made it home. Rough idle, "clacky". Next morning, did the following in order: 1) Pulled the fuel filter inspected, 2) removed all fuel from the bowl 3) replaced bowl fuel with Seafoam 4) installed new filter (my typical procedure). Without starting, I then 5) removed HPOP oil from reservoir and 6) filled with fresh oil using exact amount removed as a gauge for what to replace.
Started, idle smooth for a time. Increased rpm by depressing accelerator. Began running rougher and rougher accompanied by white smoke. Finally quit and would not restart. Cranking easily, tachometer showing RPM during crank. Suspected no fuel getting to fuel bowl. 7) Drained fuel bowl using valve on back of bowl. 8) Turned ignition to "on" to get fuel pump to run 9) removed new filter, no fuel in bowl 10) With fuel filter out of the bowl, removed fuel filter and quickly cycled the ignition to "on" and back off -- no fuel entered the bowl. 11) Removed leads from fuel pump. 12) Checked voltage across leads as ignition cycled to "on": 6.5 volts. 13) Checked fuel pump fuse (20A Maxi fuse in location 112 -- BLOWN!) 14) Replaced fuse, performed voltage test: 11.55 volts 15) Checked battery voltage: 12.44Volts.
So, with all that, how in the world does the fuel pump get 6.5 volts with the fuse blown? I looked closely at the fuse and there was no slag or connection in the element. Today I have pulled the 9-pin and 42-pin connections on the valve covers as well as the connectors to the glow plug relay module (used on Ex's) to inspect wires and connections. All looked fine. I plan to us some LP5 electro contact cleaner to clean all the connections and put some electrical grease on the connections, but the big question is where did that 6.5V come from with the fuse blown. I plan to pull the fuse and do the same test to see if the 6.5V is still there.
View 8 Replies
My feed truck (2001 ext cab 4x4 7.3 198k) had a cold starting issue I fixed with new gp relay. Now I noticed when it gets down below 30 degrees it has a cylinder miss until motor warms up. I don't doubt injectors are in my future. I was wondering though if that is common for worn injectors or if maybe something else has gone haywire and how long can I run it like that before something else tears up? after about 7-10 min the miss goes away and I don't notice it. I would like to get through the winter before messing with it or having injectors put in it...
View 14 Replies
I ran out and test drove a new to me 2001 F350 7.3L tonight. Everything seemed good, until I got back from the test drive. I pulled in and was sitting there with it idling. It seemed to idle fine, then a very small miss and very small shimmy then idle fine again; then another small miss and another shimmy. It continued like clockwork. Every time it seemed to miss and shimmy, the RPM would drop just a little, but not much. Does an ICP sensor sound like the problem, or maybe something more serious? 2001 F350 7.3L with 235,733 miles new trans, turbo replaced at 150,000 something miles. No blow by. Idled fine before driving, also drove fine. It doesn't seem to surge when idling, just kind stalls and shimmys for a split second then idles fine for a few seconds.
View 1 Replies
My daughter has a 2001 Ford Escape, V6, Automatic, 2WDR, 132,000 miles that is having starting problems. When you turn the key the engine will try to start. You have to push on the gas pedal to keep it running, it will not idle until it gets warmed up. If you try to drive it while cold, it has no power. Reading previous posts I have already replaced the spark plugs, intake gaskets, air filter, EGR, TPS, and fuel filter. Check for crack hoses / vacuum leaks. It is still not starting properly. No engine codes. New problem is oil light is flashing but the engine has oil. All of the gauges, lights, functioning normally. What do I try next?
View 1 Replies
I am having a lot of issues with my 2002 ford escape, a while if I drive the truck acts normal, but after driving it starts missing when beginning to accelerate at a dead stop check engine light starts flashing pulled codes coming up with #4 cylinder misfire and #5 cylinder misfire detected, also a catalyst system below threshold bank 2, I have had the vacuum lines repaired and still no changes and went through and changed my grade of fuel from regular unleaded fuel to premium fuel, actually went worse with using premium fuel. I was thinking of replacing all three coil on the front of the motor, putting new plugs in it and seeing what that does.
View 2 Replies
I have an 1999 f150 4.2l only 82,000 original miles.i have had truck since new .i just replaced the spark plugs for the first time.i used autolite plat. I also changed fuel filter the truck started to run like crap now shaking and sorta like missing.i pulled the plugs again rechecked the gp reinstalled them installed new wires still runs like crap.went out bought new motorcraft plat. plugs gapped at .054 still runs like crap..so i checked the gap on original plus that have been i the truck since new the gap on them are .074-.075. should i try and gapp the new ones to this the truck ran like a dream with the original plugs at this gap????
View 14 Replies
My brother has an 02 ford escape that he bought cheap because it needed a transmission. He just replaced the transmission in it as well as tie rod ends, front axles, axle bushings and seals. The front pads and rotors are new and the tires were just rotated. Now when you are going 15mph and up and are on the accelerator there is a severe shaking as you accelerate and a loud thumping noise. If you let off the accelerator it goes away. If you get it going fast enough it will shake so bad the mirrors will shake. He is a ford mechanic but said he is having a hard time pin pointing what it could be . He took me for a ride. He said he has had other mechanics look at it but they can't figure it out.
View 5 Replies
Fitted new snow tires with the intent of leaving them on year round. Now find that the Escape is pretty well un drivable due to shake at all speeds. Balance has been checked by two tire shops. I think that the problem is that the deep blocks of tread are "squirming"The tires are surprisingly quiet but unfortunately will have to go.
View 2 Replies
My father owns a 2003 Santa Fe GLS with the 2WD 2.7L V6 engine.
Recently it has been having lots of power loss issues. It vibrates/misses when idling, if you put your foot down on the gas pedal, whether under load or not, it sometimes stalls or just sits there. We took it to Hyundai, and they had no error codes. They charged us $150 to tell us nothing is wrong with it, when clearly something is. The car has become downright dangerous to drive because it cannot make it up hills without stalling/losing power.
The most recent thing we had done to it was the wires/spark plugs changed, which I think was at 65k on the odometer?
View 14 Replies
My problem is my 2001 Santa Fe petrol 2.7 L its done over 300,000 km one day it sounded like a click when driving, then when I started it cold in the morning it was missing [not running right] and had no power until it warmed up the spark leads are not that old anyway I put new spark plugs in it it seem to run a lot better but seems to be down on power on hills I think coils are ok? the motor not smokey but burn little bit of oil.
View 10 Replies
I have a 1999 F250 Super Duty 5.4L, 118,000miles...engine seems to idle somewhat rough but tach doesn't seem to move off 1000rpm & when giving slight acceleration seems to act like its missing, shaking . But under acceleration moderate or high purrs like a kitten! Always starts good , few cranks. Any hints on the what issue might be?
View 2 Replies
2001 f250 7.3L, 289,000 miles, changed the IPR and ICP, noticed the EBP tube was in two pieces. Would this cause the rough idle and shaking? IT started running rough and would die after a mile or two. Would have to wait 30 minutes before it would start again. That is when a buddy told me to change the IPR and ICP the ICP plug was covered in oil as well as the top of the ICP. So I changed the wiring plug as well. I originally cleaned and changed O-rings on IPR but then it wouldn't start, bought a new IPR and started but runs rough. I just started it with EBP tube removed and sensor unplugged. Idling rough when I press accelerator and RPM go above 2K it levels off pouring black smoke everywhere.
View 3 Replies
I have a 2009 f250 with 70,000 miles on it and for the last 6 months I have been experiencing some power loss. It happens every time there is the slightest incline on the road, it has to down shift to 3rd gear just to maintain that speed. If I don't push on the pedal until it down shifts to 3rd I slow down to 40mph no matter what the speed was before I hit the incline/hill. I also went from 14 mpg to 10.5mpg. I have heard so many theories and am curious if the fact I upgraded to 35 inch tires and never updated the trucks computer.
View 10 Replies
I checked a few fuses when my 12v power sources quit working and now the engine won't start. I get a start system fault and hill incline fault among other warnings. What happened?
View 2 Replies
