Ford 6.0L Power Stroke Diesel :: Unable To Move Selector On Lock Out Hubs
Mar 18, 2015
I have a 2003 f250 and I am unable to rotate the hubs from automatic. I have removed them and while I had them apart, I was still unable to rotate the selector. It wouldn't turn even with a crescent wrench putting pressure on it. I repacked them with grease and reinstalled and they still work when in 4 wheel drive. I am just concerned that when the vacuum does go out, I will not get the hubs to manually lock in.
View 10 Replies
Advertisement
New to the 4x4 6.0 just bought an 06' King Ranch 130K miles. My other truck is a 95' 7.3 non 4x4 now for sale. So the new to me 06' will not lock the hubs in Auto mode but will in Manual. I have good vacuum down to each wheel hub which is where my question is.
The vac port at either wheel I get 20-30hg however I believe this is only because something is plugged. If I pump up my vac tester to ~25hg right at the wheel port the needle doesn't move, holds vacuum, but does not Auto lock the hub. So I pulled out the Manual/Auto hub by removing the 3 torque screws thinking my vacuum should then go to 0 but it doesn't it stays right at ~25hg.
Before I bought the truck there was some work done to the front end. New ball-joints, Rt tie-rod and perhaps a few other things I haven't ID yet. Could my problem above be an axle seal or something else perhaps installed incorrectly causing the small vac hole going down inside the hub to be covered up or maybe plugged somehow? I believe to replace the ball joints the axle, hub and other parts have to be removed, correct?
View 12 Replies
My transfer case engages the front drive shaft spins but even when I manually lock my hubs neither of my tires will pull! I was thinking either the hubs are shot but I was told it could be the 4wd locking solenoid??
View 1 Replies
Coming home from a trip with my truck pulling the 5th wheel, we heard noises that seemed to be coming from the front hubs that sounded like stones in the hub caps. Once we got home I pulled the front lug covers to see if any came loose and were rattling around inside, but all were torgued properly. Everything drove strait and tight with no noticeable problems, should I be concerned....
View 8 Replies
When I park over night while in 4x4, the next morning my hubs are disengaged and I have to manually lock them. There is an apparent slow/slight leak in the vacuum system. What would be the usual suspect, so I can start at that point?
View 3 Replies
I got new auto-locking hubs. The updated ones. As I proceeded to replace them, I pulled out old ones and when driver side came out, there was like 1/2 ounce of water that flowed out from where the auto-locking hub would sit. Strange. I had changed out lines, vacuum pump, vacuum solenoid and reservoir. All new and dry. I blasted both sides down with brake cleaner to clean off old grease, let dry and installed new auto hubs. So far so good. Will test the ESOF feature another time. I was wondering where this water would come from? Other side of wheel hubs are dry.
View 2 Replies
I've been told that manually unlocking the front hubs on my '15 F350 dually, might just improve milage. Any concerns about the axle lubrication from being unlocked for extended periods of time? I rarely need the 4WD.
View 9 Replies
Just notice this in the manual page 302 The vehicle should not be driven in 4x4 high or low with the lock hubs set to auto as this condition may damage driveline system components.
Page 303 It then goes on to say !!
Automatic operation of the hub locks is recommended and will increase fuel economy.
when using 4x4 once in awhile LOCK or AUTO
View 14 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didn't have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines, harness, pump, sending unit , tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to the garage had them swap it out and now they said come get the truck they won't work on it anymore that now it needs 3 injectors and they won't touch it with aftermarket fuel system on it. So i go to drive it home and it starts but runs rough and u can hold it to the floor and it won't budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now.
View 10 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
View 7 Replies
I have a 2004 6.0 with the 5L110 transfer and torqueshift transmission. While test driving after installing everything, I didn't get 7 ft down the road and the tires locked up and she came to a dead stop. Now I only have reverse but I can still feel the tranny engaging into drive but will not move.
View 2 Replies
I have a 2006 F350 4x4 dually (6.0 diesel obviously) automatic. It's got 200kml on it and a second motor (found the sticker on the valve cover). I just bought it a month ago and have only driven it like 100-150 miles. Previous owner imported it to Finland 3 years ago, but never registered and only drove it like 500-1000 miles (with temporary plates to carry his racer few times). Original owner was a company in Southern Midwest that had some equipment on back. (It's was sold as a chassis cab new.)
Now I was getting the truck tested for registration yesterday. Drove it there 30 miles (country roads and highways), no problems. Then we had to do the smog-test, which is a bitch. They rev the engine to limiter (4200rpm) couple of times and measure the particles flying out. Passed it flying colors, but when trying to pull out the transmission wont engage!
Shifter linkage ok. Oil in tranny clear and plenty. When I put on R or D the engine RMP rises very slightly (maybe 50-100 rpm) and then settles back. But nothing else happens.
Luckily got a friend with large flatbed that we used to carry my baby home. But now I don't know where to start... ...well, I do have couple of ideas what could be broken. Specially if there's something simpler than dropping the whole tranny out (it's HEAVY and it's cold&wet out there) and rebuilding the whole damn thing.
Previous owner told he had some shifting issues couple of years ago (maybe 500 miles ago) and they "rebuilt" the tranny. He DID replace the hydraulic "logic board" and solenoids + new packs while at it. Naturally new filter & oil too. He said the torque converter was "tested" to be in good condition and they used the old one. I can tell the tranny has been out of the truck and the seller felt legit (a car guy too).
View 14 Replies
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
View 6 Replies
I fear my truck may be stuttering on acceleration.
I hooked up a fuel pressure gauge tonight and the fuel PSI at idle and under acceleration... barely moved. Stayed between 60-62PSI.
I'm thinking this isn't normal... shouldn't the PSI be reduced especially when I accelerate hard ?
I'm thinking the "delivery" fuel line... perhaps there is a bottle neck somewhere which is causing constant PSI at the fuel housing ?
View 3 Replies
My folding mirror on the drivers side folds out good but when bringing it back there is a clicking sound and it doesn't move, a slight pull on it and it comes back ok. 2011 F350 SD.
View 7 Replies
Bought this truck (06 F250 cclb diesel) earlier this year and (as far as the seat is concerned) worked perfectly until about 2 weeks or so ago, when I learned that the passenger power seat works in every direction except for to move the seat back. Since every one that got in the truck didn't believe me and now the seat is almost at the glove box I finally decided I should do something about it. I have removed the fuse and let is sit with the the fuse out for about an hour, no change. I had read on another fourm that if you recline the seat back a few times it resets the module, attempted with no change. It is to the point I need to get into a bit more serious diagnostic processes however I am unsure exactly where to start.
View 2 Replies
My Excursion is having an issue with the 4x4 system. The. 4x4 selector switch on dash lights up properly for 4x4, but the auto hubs don't actually engage. The hubs will lock only if I manually lock the hubs. I can hear relay click, so I don't think its electrical. The hubs had new o rings installed when I did front ball joints a few thousand miles ago, and the 4x4 worked fine up until today.
View 5 Replies
I have a 2005 Ford F-250 Powerstroke. At times when stopping at light or for any reason, I give it gas but it does not want to go. It's like it is not even registering that I am pushing the pedal. I shift it into neutral and rev it up then switch it back to drive and it goes and puffs out smoke. What is going on?
View 6 Replies
2003 F350 6.0 cc 4x4 with 291k... Not sure if I have a problem or not, it happened at a signal light: The light turned green, I pressed the throttle and started to move. As I pressed more, there was no response. Second later it took off and I have had no more problem. What the cause maybe?
View 1 Replies
I purchased 2011 F250 King Ranch Edition about 3 months ago. I'm loving the truck and not had any issues until 3 weeks ago. I locked the truck as usual using the key Fob, and upon returning to the truck, I noticed the doors weren't locked. After some brief trouble shooting, I discovered the the fuse was blown that according to the manual controls just the power door locks. I thought it was strange that a new truck would be popping a fuse so I replaced it...a couple of days later it blew again. This time I was locking the truck with the door key pad. I took it to the dealership and they checked it over and said they replaced the fuse and cycled it numerous times but could not reproduce the problem. The told me that they even put a call in to the Ford engineers and they said check the key pad for water intrusion. The dealership told me they disassembled the key pad and found nothing wrong....lock and unlocked the door some more and the fuse would not blow. I picked the truck up four days ago and the fuse blew again last night. Everything else works...alarm sets and goes off if any of the doors are opened. The only thing that I can find that doesn't work when the fuse is blown is the remote start.
View 14 Replies
My mirrors on a 2016 explorer don't move when we lock the doors, or move into position when we unlock them.
View 1 Replies
