The power steering seems to work fine and dandy. But when I turn the wheel all the way to the right, or to the left, the serpentine belt squeals, indicating that the power steering seems to have faulty valve or whatever. What is causing this problem?
View 6 RepliesDue to being low, and taking my splash guards off to put on my skid plate, in heavy rain, my belt I guess gets wet, slips and I lose power steering. I can hear it screech.
I didn't think that would be the case for snow, but sure enough after plowing through my driveway to go to work it was slipping screeching and loss of power.
Well, two years after I replaced the pump bearing and the power steering is acting up like the belt is slipping. Sometimes it works fine, sometimes the steering gets jerky and hard.
The fluid level was fine, but I changed out the old stuff anyway, the belt is fine and not loose. I also pulled the pump apart to inspect it and it still looks as good as new.
When it acts up at a stop, it will squeal, but like I said, the belt is not loose. It's almost as if the rack is bottoming out against the bump stop (it's not) or the valve that lets excess pressure is dumping pressure randomly.
I took the valve apart with the pump and it looks fine, no scratches. Do the rack or valve go bad? If so, what was that like and could my rack have a seal leaking inside?
I have a 1997 Ford Aerostar rwd with a 3.0 L v6. I would like to know how can I remove the power steering pump. Furthermore, the reason I am changing the power steering pump, is because I am changing the rack and pinon mechanism. Additionally, I found the rack filled with hydraulic fluid. If possible pictures would be a nice addition to your respond.
View 3 RepliesProud owner here of a '96 3.0L RWD Aerostar Utility Van with about 138k miles, and leaking power steering fluid. At this point I'm replacing fluid from zero every time I have to drive it which is about once a week. I've located the leak and it seems to be coming from the pump/reservoir around the pressure hose. The hose is loose as in i can move it around a bit, but from what I've read, this is normal and the hose is supposed to be like that. I figure that at this mileage, with so much air going through the pump, all the crazy squealing and whining it does even when full, at this point it probably makes sense to replace the whole pump while I'm in there, as opposed to just doing the reservoir. Anyway, I'm planning to do this in a couple of weeks, and have some questions...
1) The pump - I've read on this forum that the best way to go on brand of the pump is Motorcraft.
2) Hoses - I'd like to replace the hoses coming out of the pump while I have this thing all taken apart, but I'm not exactly sure what parts to get. I know one is the pressure and one is the return, but there are variations of each based on the research I've done. The parts on the Napa site have different descriptions like "with switch port", "without switch port" "56in hose" "26in hose", and so on. Which ones I need, specifically the ones connecting directly to the pump? I havent been able to find anything in my research online, in Haynes, or Chiltons manuals.
3) Washers - Whether or not I replace the hoses, should I replace the washers at the connection point? Chilton's seems to recommend replacing them. Will they come with the new pump?
My local auto parts shop has the pulley remover/installer for me to rent so I've already got that squared away. I'm pretty sure I've covered all of my bases otherwise.
I have a 92' Areostar XL 3.0 2WD. When I first start it and put it in drive it takes a few minutes before it kicks in. After a few minutes of driving it doesn't have a really bad problem (only a few times has it slipped in lower gears.) I was told it could be a clogged transmission filter, old transmission fluid that is glummed up, or pull belts need to be tightened. I have the van up on jacks now and was getting ready to change the filter and fluid but I decided to get some advise first before I screw things up or do any unnecessary work.
View 14 RepliesMy 2007 Ford Focus broke down today. From what I can see and find online with my limited knowledge, it looks like the serpentine belt broke. Would this cause loss of power steering, rise in oil temperature and my check battery light to come on?
View 11 RepliesI have a concern with my serpentine belt chirping when it's wet or cold. I have tried soap, and other attempts to quiet it down. Belt tension is good, new water pump and fan. Otherwise no other issues so far.
View 9 RepliesI was driving the other day (cold weather- approx 15 F), and my serpentine belt shredded. Managed to drive a mile or so to my driveway. The belt was shredded on the fan side (and had come completely off), but it wasn't torn in two. Got a new belt and installed it, but upon test-cranking, found that it was riding up one ridge on the crank. All the other ribbed pulleys were fine (PS, AC). The smooth pulleys had the belt move a little, however.
Thinking I didn't set it right, I reinstalled the belt on the crank and tried again. Same result (belt rides up one groove, towards the fan). I perused the archives, and one comment was that someone simply trimmed one groove off the belt and everything was happy. The belt found it's "groove", and didn't act up anymore. Doesn't fix the underlying problem, but
1) is this a good fix
2) any clue what is going on?
3) Do I need to get the crank fixed?
BTW, I am sure that I threaded the belt on correctly!
1992 Aerostar, 4.0L, AWD. AC+P/S....
Whats the easiest procedure
View 3 RepliesThe Ex just started making a sound that I can best describe as a hiss or squeal, but not as much of a squeal as the belt were to make if it were slipping. It starts around 1700 rpm and gets louder as the revs increase. The truck also feels maybe a bit down on power but that just could be me not willing to push the gas as it squeals louder when I do. I don't see anything leaking and anything out of the ordinary under the hood. All gauges are normal, turning the a/c on or off doesn't change anything. Nor does the radio. Any clue as to what my problem is? I'm a little worried driving home if it's something potentially serious.
View 14 RepliesI purchased a new 2000 mazda b4000 2 weeks ago and the belt was squeaking and I knew I had to change the water pump so I replaced it and the squeaking didn't went away... I thought maybe my idler pulley bearing was worn out cause I could see it wobble back and fourth when the engine was running... Replaced it, still squeaking! Change my belt still squeaking! look further turns out my power steering pulley wobbles slightly. I'm thinking about trying a gator back belt and see if the squeaking goes away. Could it be dangerous to run the truck as it with a slight misalignment in the power steering pulley? or it'll be a must replacement asap?
View 3 RepliesI have a problem with my 1997 aerostar. There is a squeaking noise that gets more significant when I turn. I am pretty sure this is the drive belt as the power steering fluid is fine. Should I attempt to replace the belt tensioner and if so is it just the pulley that needs replacing or the whole tensioner. I am by no means a mechanic but can figure most things out.
View 5 RepliesI have a 2005 f-350 4x4 with a 6.0 power stroke now it's been causing me problems to the fact I couldn't find the problem the truck would smell like an electrical fire but last night I found that the belt is slipping on the seized a/c pulley but I can still spin the center clutch so can I just replace the clutch assembly? Or bypass the a/c so I can drive for the time being?
View 1 RepliesI have a 350 chevy small block in my 79 camaro and the power steering belt is constantly slackening. I have not driven the car more than a few hundred yards because its not yet street legal so it is not becoming loose due to it just stretching like normal over the first 100 miles. I have a brand new power steering belt and have replaced the power steering pump as well. i have tightened the belt twice now after i have just run the car for a couple minutes without it going anywhere and each time it slips back to where it is loose again. I have tightened all the bolts and it keeps doing it so I'm not sure what to do now.
View 1 Replieswhile out of town the big belt that runs the alternater and ac broke and took out the power steering belt. I replaced the big belt but do not know how to do the power steering one. I can hardly see the back sprocket.
View 6 RepliesI just replaced a serpentine belt on a 2004 chevy Impala. Now the power steering will loose some of its "power". I at first loosened the bolt on the tensioner not knowing how to properly make it release, then tightened the bolt back after realizing my error. I know it did not move though.
View 5 RepliesMy son called me today and said his power steering belt went bad. He says it had been making noise for a while- at least that is what he thinks the noise is- a kind of high whining sound when you first start the car? I don't know if that makes any sense or not. He also said that today not only does his power steering not work, the car is now acting strangely electrically speaking. The speedometer and the radio have stopped working completely. Is any of this related? I am completely clueless about electrical problems- other than the possibility of some blown fuses or a wire that shorted out. The car is a 1997 Mitsubishi Eclipse Spyder. He is out of town at school I don't have the luxury of looking at it myself to troubleshoot or give any more particulars.
View 6 RepliesI can't remember how to tighten my power steering belt. I've loosened the 12 mm bolt that locks the PS pump in in place. But how to I increase the tension? This is killing me, because I replaced the timing belt in July. I guess I've since killed the brain cells that I used when i put the power steering belt back on.
View 9 RepliesI was backing out of my driveway yesterday with the ac on and as I hit the gas it sounded like a belt was slipping. Now this only happens when the ac is on. When it is off nothing happens.
View 1 RepliesThe AC/power steering belt in my 2004 Santa Fe, 2.4L has intermittently squealed for some time, but lately the squeal has gotten louder. Initially it only happened when the compressor was on, but now it happens when the compressor is off. I have not experienced a loss in steering power but I did notice that the power steering fluid appears to be discolored. I have replaced the belt and re-tensioned it several times hoping this would solve the issue, but it hasn't. I intend to take the belt off again and see if the pulleys all spin freely. When I replaced the belt initially, everything did spin freely. My guess is that the power steering pump may be shot and is putting excessive load on the belt, however, there is no PS pump "whine" and again, no loss of power steering. It looks like I should also check for separated pulleys.
View 3 Replies