Ford - Explorer :: 2006 - Shifts Really Hard?
May 2, 2012
my wife has an 06 with 77,xxx miles on it. as far as i know there has never been any tranny upkeep done on the vehicle. we have owned the care for approx 15 months. it doesnt act up all the time. it will shift real hard into reverse, feels like it is popping into it real bad. then at times it feels like it slips very little going into overdrive. and at times it will pop when shifted into drive. it is hard to predict, i thought maybe when it was warmed up and the fluid was warm it might not do this, but it does. i know nothing about this thing, the dealer wants me to bring it in so they can plug it in?
View 5 Replies
Advertisement
I have a few problems with my explorer. I was just wondering if there's any way I can fix them on my own instead of paying a mechanic. I
1. back passenger window wont roll down .. .
2. Gas gauge fluctuates can't get an accurate reading on it .. .
3. service engine light comes on for a couple days, then goes off .. .
4. shifts hard if i go over 65mph and then slow back down .. .
View 3 Replies
My speedometer is jumpy, odometer quit working at same time. Shifts kinda hard going into 2nd and 3rd gear. I am at wits end. I have replaced both speed sensors, checked all fuses, and also tore dash apart checking the worm gear in the cluster. I don't want to take to the ford dealer. The truck got 172,000 on it but been very well maintained. I just don't think its the transmission. Its got to be something easy.
View 9 Replies
My wife's car, '06 explorer 4.0, experienced trans. slipping issues last year. The trans was replaced under extended warranty. Now it's doing the same thing. Warranty expired. The dealer claims they can't find a problem. It does it when you slow down at a light and then accelerate without stopping, or going around a corner and accelerating. It shifts but requires more rpm to move. Almost like I am dragging a piano or something.
View 2 Replies
I have 99 f350 v10 4x4 and trans shifts great under light rpms but 2-3 shifts very hard. At wide open from about 35 mph it will shift down and take off like a bullet but wont shift until I lift my foot and then it bangs hard from 2-3. All other gears are smooth. I did some searching and have found some threads saying it could be an accumulator spring that is broken? Truck has 115,000 miles on it. love the truck but want to fix this before it does some damage.
View 1 Replies
I currently have a 2006 F-250 6.0 with 187,XXX.
My problem that i am having is that the transmission recently within a couple weeks started acting weird about the same time 3 of my fuel injectors started failing. When i start up the truck and put it into drive it takes about 3-5 seconds to shift. Once it's in drive it runs pretty well but it will start shifting out of normal when i go to accelerate. Also when i go to slow down sometime the transmission shifts hard to a lower gear. I also have a video of the sound that it had started to make since its hard to describe.
Here are attached videos and photos. I want to hopefully fix the problems myself so i can learn more about my truck. I am going to handle the fuel injectors here soon since 2 are failing and ones about to these have been causing the truck to shudder at around 47-53 mph but after that its fine.
The transmission is stocked and never been altered, i do admit for 3-4 years I have changed the fluids or filters.
The truck is bullet proofed, sct tuner, upgraded turbo from stock, 4" exhaust, head studs and new everything when the engine was rebuilt and bulletproofed.
I plan on going to ford tmw to have them figure out the problem and hopefully its just solenoids so i can fix it myself. I have a link posted also where you can hear the noise it has been making when in R P and when shifting going down the road and it is a automatic.
YouTube.....
View 14 Replies
I have a 2009 V6 Ltd with about 15k miles. It has always seemed to shift a little too hard from 1st to 2nd and from 2nd to 3rd under light to medium throttle. Does this sound like a transmission ill that can be fixed by adjustments?
View 8 Replies
I bought a 2010 Elantra touring last September (it now has 166000 km). I love the car except for the hard shifts. It happens every morning when moving from a cold start. They vary from slight to pretty noticeable. I had the transmission flushed shortly I got the car. I just had the transmission reset about 2 weeks ago. It was smooth as glass for about a day or so after. Then back to square one. Yesterday it hesitated shifting between 4th and 5th going back and fourth a couple of times.
View 2 Replies
It is a 2006 Explorer with the 4.0 and around 89,000 on the odometer. Around a couple weeks or so ago the wife said the explorer was hard to start one evening and it has been like that ever since. It cranks for about 5 seconds and then fires. So far it has started every time since this issue began. This is really the first issue we have ever had other than the radiator replacement a few years ago.
View 3 Replies
I'm a diesel mechanic and know my way around Powerstrokes, this 4.0 is not what I would usually work on, but I have a friend who has 2006 explorer 4.0L SOHC, someone told him he needed a motor with out explanation why, so I didn't want to see him get ripped off. The problem is it idles very rough, hard to start, and stalls. There's no DTCs , if you hold the accelerator slightly it will stay running, but once you let off it will either idle really bad and misfire or cut off, once pushing the accelerator the rpms raise very smoothly up til 3500 which is what I assume the rev limit is in nuetral.
I've done checks with focom and forscan, I was thinking possibly a bad fuel pump, while monitoring fuel pressure I see a range of 289 - 326 kpa with 26% fuel pump I guess duty cycle would be the correct term(once again I'm a diesel guy, and use to dealing with IPRs and Hpops) not sure if the desired fuel pressure is relevant on these but it always stays at 269kpa. I believe that equals out to 40-48psi while I believe this system is supposed to have somewhere in the range of 60 - 70, but I wouldn't expect to get a rough idle with no load with almost 50 psi of fuel pressure.
So with no DTCs Im baffled, and don't want to start wasting money just throwing parts at it. I've thought everything from fuel pressure sensor, to coil pack(replaced 4 months ago) to crank and cam sensors.
I did end up getting a code p106, but I believe this is because I didnt tighten the intake hose after checking the throttle bottle, I just slid it back on. out of the 4 days of testing first time I seen a code pop up besides unplugging some sensors here and there to make sure the pcm would actually register a dtc.
View 3 Replies
Tranny started acting funny recently...shifting hard into reverse at first, then last night it was like it was stuck in high gear or slipping on the way home. Limped it home and took the following codes:
P0743 TORQUE CONVERTER CIRCUIT ELECTRICAL
P0750 SHIFT SOLENOID A MALFUNCTION
P0755 SHIFT SOLENOID B MALFUNCTION
P0760 SHIFT SOLENOID C MALFUNCTION
P0765 SHIFT SOLENOID D MALFUNCTION
P0962 PRESSURE CONTROL SOLENOID A CONTROL CIRCUIT LOW
P0966 PRESSURE CONTROL SOLENOID B CONTROL CIRCUIT LOW
P0970 PRESSURE CONTROL SOLENOID C CONTROL CIRCTUT LOW
View 1 Replies
I've noticed that my 2013 STX F150 4x4 5.0L shifts quite hard from 1st to 2nd. This clears up when I pull the battery cable for 30 minutes but comes back in about 2 weeks.
Is this a pretty normal thing?
View 7 Replies
I just rebuilt my E4OD transmission in my 1996 F250 7.3L it has all new clutch packs torque converter and a shift kit. When I first put itback together it would not shift out of second cleaned mlps and shifts threw all the gears now. I took it out on the road to test it and this thing ran great shifted smooth and quick could not askfor any better but when Trans temp gets around 140-150deg it shifts hard and od light flashes. I have ordered a scanner to read the codes but won’t be in till later this week. What I could check in the meantime.
View 13 Replies
Have an 01 f150 super crew 4x4 with 5.4 li shifts hard from 1st to 2nd - What could be the problem?
View 1 Replies
Replaced the 2002 ford explorer 4x4 traction control module because of a shudder in first gear. With the new module the shudder disappeared but now the truck shifts into 4wd by itself and stays there. I am now on my 2nd new module because I returned the first one thinking it was defective.
If I cycle the 4x4 high switch and the 4x4 auto switch, the truck switches back int 2wd but on for a moment then goes back into 4wd. I don't get a 4x4high indicator light but I can hear and feel it is in 4wd. Almost like it thinks the truck needs work with the traction. I have now disconnected the module completely and the trucks runs/shifts beautifully in 2wd. I know my transmission is good. BTW, I have no trouble codes.
Do I have a bad speed sensor somewhere? and How do I trouble shoot for it?
View 8 Replies
I've just bought a used 2002 Explorer Sport Trac (Automatic) 120k+ odo and what I've noticed whenever I shift from Park to Reverse or to Drive it takes about 3 seconds before I feel a slight jerk moving forward before I can step on the accelerator for the vehicle to move backwards or forwards but if I step on the accelerator right after shifting to any gear except Neutral it won't run immediately as if the clutch is disengaged and after about 3 seconds it will suddenly engage. Is this normal or is there something wrong with the transmission?
View 3 Replies
My 2010 Ford Escape Shifts hard, but only first thing in the morning. After it warms up I doesn't seem to do it. It has 66,000 miles on it and and when this started I took it to a transmission shop and they flushed out the transmission fluid. There were no warning in the computer for the transmission. I'm thinking it may not be the transmission, but an acceleration problem. Could this be true?
View 5 Replies
2000 Ranger autimatic, 2.5 lt 2wd, 155,000 miles. To my knowledge it has never had a tranny flush or the fluid changed. I have noticed last week that when you are taking off from a stop sign it jerks going into gear. This only happens when you are taking off all the other shifts are smooth. The transmission fluid color is redish-brown and doesn't have a burnt odor. I don't know where to start. Do I get a tranny flush, change the fluid or is it something else?
View 5 Replies
I have 1993 F-350, 4X4, four door with a 460 fuelie and a 4EOD. That"s a bunch of 4's! I bought this pickup with 186,000 miles on it in 2005 or so, really just to haul fire wood and go to the dump once every 6 months. I don't know if the the tranny has ever been rebuilt. Nothing else on the pickup has been rebuilt. It now has 196,000 miles on it. In the past the tranny always shifted like a stock 4EOD. Kind of slides into the first three gears then into overdrive pretty solid. I took it out to go to the dump last week and it was just like always until it took it to taco party last night and it started to shift real abrupty. Doesn't matter how fast you go, it hits just as hard if you are on the gas or just casually cruising. It is hard in every gear. My first thought was that it may be low on fluid. When it is hot, idling in park after a drive I don't see oil in the little holes on the dip stick. I see oil on the dip stick but not in the little holes. Am I correct in thinking I should see oil in the holes? Actually I will see oil in the little holes when I first pull it out, then if i wipe it, put it back in, I see no oil in the holes. Engine idling in park of course.
View 2 Replies
I just had my tranny rebuilt it doesn't shift hard all the time but it does from time to time going from 2nd -3rd and 3rd -4th I thought being new it may need to soak up some fluid so the bands can swell so I ask the shop that rebuilt it that question he said they soaked them as they rebuilt it so they should be swollen already then he proceeded to tell me it was electrical is he telling me the truth because the ck engine light isn't showing any faults and if it was electric shouldn't that have been fixed in the shop while it was being rebuilt if it was interior electronic?
View 1 Replies
Shifts slowly or stays in shifting mode longer than necessary. Must stop accelerating and wait a few seconds until the shifting is complete. Does something need adjusting?
View 6 Replies
