It seems like I am going thru brakes I just replaced my brakes in May and my Rotors in July and when I brake my truck shakes like crazy. Is it the brakes again or am I missing something.
View 7 RepliesAfter my 2006 Ford F150 Lariet started shaking and pulsating when braking (38,000 miles) I took the truck to the Ford dealer and asked to have my brake pads checked. They came back and siad they looked fine and I had alot of wear left. Then I mentioned that is was shaking and asked them to check it again, they drove it and then said my rotors are warped and I need to replace the rotors and pads. I don't haul, tow or do anything crazy with it.
Now, here's my questions:
1. Can the rotors go bad and the brake pads be fine?
2. Should I go with a ceramic pad or stick with the OEM?
I'm just a female and don't want to be taken advantage of at the dealers. Cost is not an issue when purchasing a good product.
I was driving my f150 going down the highway. Cruise set at 110kmh. All of a sudden truck started shaking And sounded horrible. Shut off the cruise. Floored it.it misses fired like no tomorrow and no power, looked down check engine light was flashing. Then all of a sudden everything normal. Now its intermediate and light solid on. So I thought I will just I will hook up the code reader. And NOTHING it didn't turn On. No beep nothing. Tried 2 readers no connection. Trucks a 2005 ford f150 fx4 5.4 217600km on the clock
View 2 RepliesI have a 2005 F150 XLT with a 5.4 (198,000miles) RWD. A few months back it developed a miss due to bad COP's, typical shuddering around 50-60 MPH.
I pulled off the COPs and while I was in there I pulled my old plugs as well. New Motorcraft SP515 plugs went in with a little nickle anti-seize being careful not to get any near the end of the plug and I put a set of Granatelli COPs on with a little di-electric grease on the inside of the boot. The miss went away and the truck drove like a champ.
I will also note that I replaced the front wheel hub/rotors, front calipers and new pads. I resurfaced the rear rotors, new pads and new E-brake shoes also.
The issue I am having is under light acceleration, or "normal" driving conditions the vehicle has a mild shake which eventually smooths out.
My first assumption was that I did not torque my front wheel hubs correctly or that I messed something up so I took the truck to my local front end/alignment shop for a full inspection and they said everything is great. They also said that they didn't really feel the vibrations that I mentioned. I am used to this truck driving very smooth up until the misfire situation so to me it is quit noticeable. After the front end shop I went to Discount tire cause they mentioned that my rear wheels are bouncing pretty good and that may be what I am noticing. Turns out the tires were out of balance which Discount took care of and rotated my tires while I was there.
The vibration is STILL THERE! No CELs to reference, just an obnoxious vibration. I tried to isolate the issue by accelerating in 1,2, and in D. The issue occurs regardless of the gear I start off in.
Lately my 2007 GX470's steering wheel has a shaking/vibrating problem whenever I apply the brake at speed above 50 mph or so. Without braking or with braking at slower speed, there is no problem at all -- everything is glass smooth.
1. I assume the front brake rotor is warped?
2. Will I need to change the rotor or is there a way to fix the warp (it that's the problem) without changing the rotor?
3. Approximate part & labor cost?
I plan to bring to dealer for a check up but would like to know ahead of time what to expect.
I drive a 2004 chevy Tahoe and have had this problem for about 8 months. It started out very faint and occasional, but has now escalated to loud and consistent. So it ONLY happens when turning right. I've tried to replicate it when turning left and had no success. It happens when I am turning fairly hard at a decent speed. ex. Pulling into my driveway. I've already checked the wheel bearings and Ball joints.
Another thing is that the ABS light is on sometimes when i start the car and comes on every time i turn the steering wheel all the way to the right. It also has a problem where it will shake almost uncontrollably when driving at 65+MPH after hitting a bump or sometimes just randomly on a smooth surface. We just got new tires and balanced them. It did the same with the previous set we had. I know I'm asking for a lot, but where to start?
2007 Ford F150
XLT 5.4L Supercab
55,500 miles
Only Owner
I have owned my truck since mile 1 and have not had any issues up to this point. That being said in 2011 there have been 5 occassions where I have been on interstate driving between 55-70 and had to pull over due to my truck shaking. This shaking is very extreme and truly scares me, thus the reason I pull over. I replaced my tires with Michelin 70,000 mile tires and also replace my front brakes just over a year ago.
After not being able to reproduce the shake for my mechanic, they said my upper front ball joint needed replaced and my rear shocks. They hooked the truck up to the computer and did not receive any codes and my check engine light has not come on to this point.
The research I have conducted to this point has pointed to a number of issues and I had my mechanic check all of them and they said nothing was out of the ordinary, these were: e-brake issues, front brakes, calipers, plugs/coils.
I have a 2007 an at about 52mph the truck has a slight but irritating bounce (up an down) an after a while sickening. It maybe felt it was coming from the rear. So I had the rear tires balanced an the guy said my right rear tire had a bend to it. Well assuming that the balancing fixed the problem it did not. So I'm going to put on the spare to see if it still bounces what else should I do?
View 14 RepliesI've done some research on the shaking that is occurring on my truck an it's a possibility that it's the e brake seizing up. I've read where everyone has taken it to the dealer to get it fixed ....
View 7 RepliesHave a 2004 Fx4. Lately its been shaking violently when i accelerate. When I turn the overdrive off it stops.
View 9 RepliesI have a 2006 F-150, V6, automatic transmission, a little over 214,000 miles. When I started it up this morning, no issues, but when I dropped it into reverse, it started shaking pretty bad. Got on the road and put it in drive, and the shaking continued, then the check engine light started flashing. Haven't had any problems up to this point. Checked all the fluids including the transmission fluid a few weeks ago and all was well.
View 4 RepliesI have an '05 5.4L 3V and I was way to trusting in how it was running. BTW, I change the oil every 3 to 5 and have only driven highway miles, albeit a lot of them...155k! I bought it with 40k on it but was not aware of the plug change issue until I heard about it off-hand. I let the plug change go cuz it was running so well. Bad move.
Anyways, a few weeks ago it began to lose power and I suspected that the PCM was retarding the timing for some reason. Before I could get to the shop, the thing went nuts on me at 75mph. Started shaking and sputtering and throwing cel codes. I shut it down and after 5 minutes re-started. It seemed fine and actually was running a bit better. Took it in and the code was the 0302. #2 cyl misfire.
They also said the compression was very low on that cylinder and slightly low on 1,3 and 7 as well. I had them change the plugs and the #2 COP even though they said I needed a new engine and then I picked it up. Now the engine barely runs at all. It shakes violently, where to go from here. What should I do now? New engine?
I have a 2004 F-150 5.4L V8 3v vin code 5. I'm a heavy equipment mechanic and know my way around engines. The longer I own this truck the worse the problem gets. I believe I've narrowed it down to the oil actuated timing chain tensioners. I get a really bad rattle with a shaking condition only after changing my oil. Other then that it runs perfectly. I'm guessing it's losing its prime and trying to build up oil pressure. Is there any way to hand prime those tensioners? Or should I just go ahead and replace the whole assembly?
View 5 RepliesI have a 2006 F150 5.4 3v rattling and shaking excessively. I have installed two new cam phasers, two vct solinoids, two vct housings, flushed oil and installed motor craft oil and filter. This never happens if bank two vct is unplugged or in open loop. Monitioring vct's on ids only bank two is erratic. Also when I had vct housing off I blew regulated air through oil passage seems free.
View 7 RepliesOk, I have a 2006 Ford f-150 5.4L engine. it has 88000 miles on it. Here recently it has started acting up on me. It starts shaking violently when I slightly accelerate going up hills at any speed. On level ground it doesn't do it. Going down hill it doesn't do it. When stopped it doesn't idle rough.
It does this shaking when I barely press the gas. When it starts I either let off the gas or I push the gas to the floor and it stops. What is going on? This is the first Ford I have ever known. I don't know anything about these vehicles. I have read it might be the coils and plugs but then people have told me it might be the torque converter.
I just bought a used '05 F-150 and recently I noticed more a shaking I guess you'd call it. When I start from 0 to 80 nothing seems wrong, but when I slow down to coasting like 40 - 45mph and accelerate to 50 - 55 mph it shakes or acts like its having a hard time shifting or its skipping. And it doesn't happen till after I go past 40-55mph range and I've tried it in overdrive and out of it.
View 3 RepliesI have an 07 f150 v8 5.4 and it idles very rough. When i start it it seems to start really rough and just about everytime im stopped its shaking just enough to annoy me. Do you think its the spark plugs? I took into the dealer about a month ago and they said everything was fine. But its still doing the same thing. Also the A/C tottaly sucks is that they way it is? When I accelerate the cold air gets kinda warm and it doesn't get cold until i get up to speed.
View 14 RepliesI have a 2007 Ford Expedition with approx 135k miles with a 5.4. At approx 45 miles per hours it starts shaking and shuttering. It feels almost like you ran over one of those traffic bumps. I've had quite a few issues I've been working so I recently changed all my plugs with motorcraft platinum and all new COPs.
When I am going approx 45 miles per hour it will shutter for about 1-2 seconds with overdrive on. You can almost time it that it will do it every 4 seconds. With overdrive off, you can feel something dragging down the engine and hear a light grinding noise or a mechanical sound but the shuttering is less. I feel there is something definitely cycling approx every 4 seconds.
When i am doing heavy acceleration I feel that it has adequate power and now that I've replace the plugs/cops I don't feel any significant misses etc under hard acceleration (before I changed the plugs/cops I did feel misses).
I have recently been having violent shaking when I make a turn to pull into a parking spot or turn at a stop sign. I can park my truck and the truck continues to shake until I turn the motor off. When I restart the truck it runs fine. It doesn't do this all the time just sometimes. I have a 2006 Ford F-150 lariat 2 wheel drive.
View 3 RepliesSo after a decent drive when I get to a redlight / stop sign / etc the truck will idle rough and shake but giving it a little bit of gas (1k RPM) seems to smooth it out however it doesn't throw any codes or the CEL. The truck is a 2008 F150 with the 5.4 and 90k miles.
I've searched quite a bit on this issue and I can't seem to find any real fixes other than swap parts out until something works and I've heard everything from filters to cam phasers or low oil pressure (I will be taking it to the mechanic to check the oil pressure)
so far I've:
Replaced the air and fuel filters
Changed the oil and oil filter (synthetic and OEM filter)
cleaned the MAF and cleaned the throttle body
also is 2008 equipped with an IAC Valve because I've read that it wasn't and I can't seem to find the IAC if it is.
On my way into work this morning, my 06 with the 5.4 started running very rough/shaking at low rpms. I could kick it out of overdrive and it would smooth out and seemingly be fine at higher rpms.
This worked out for a couple of miles until the truck just died on me completely. The Edge is showing po351, 352, 353......358 codes. Ignition coil Primary/Secondary circuit fault on every cylinder.
I'm thinking its unlikely that every coil failed simultaneously....computer? When I try to start the truck, it will try to hit on a cylinder or two, but will not run.