Tried searching, but I couldn't find any good write-ups on how to replace a front CV axle. The boot on mine is ripped and spraying grease so I figure I should just replace the whole axle while I'm in there. In a previous post, I also found out that replacing the CV axle (joint?) is easier than replacing just the boot.
View 1 RepliesLooking to change out my front differential cover tomorrow, cover is pitted, rusted, corroded, and leaking at the seals. While under there I want to inspect the vent for the axle and differential (and replace if it's clogged - which I believe is leading to the seal leaking). Looking for info about the vent tube location on the front axle? Thought I read somewhere it was on the cover itself, turns out that's a negative.
View 1 RepliesI have a 2004 F150, 5.4L V8. A few years back I was in an accident when someone slammed into the front of my truck. The right front wheel & tire took the brunt of the accident. I thought the repair shop had everything back to normal until recently I occasionally have a grinding sound coming from the right front side, seems to be related to the axle. It doesn't do it all the time just at random while I'm driving. The only solution I can find is to pull over or slow my speed to a crawl. Once I slow down enough or turn my wheel one way or the other its like something SLAMS back into place. I had it looked at by a local mechanic and they couldn't find anything wrong. Could it be something in my right front axle?
View 7 RepliesHow do I get the front axles out of of the knuckle? It seems like the seals are holding them in? Is there any trick to to getting them out,I am trying to do my ball joints
View 1 RepliesI have a 2006 F-150 5.4L 4x4 Lariat. I was wondering where or how I could find out what gears are in my axles.
View 3 RepliesUnable to decode the B6 axle code on my f150,5.4 L,FX4 2005. Clearly located on the drives side door is the label 'axle' directly below that is B6 ! Unable to locate a listing for this code any where?
View 3 RepliesI have an 04 Limited, 6.0 PSD, 4x4 which I need to replace the front inner axle seals, the right side is leaking out the shaft. I have watched a couple of YouTube videos on how it is done but would like to get some first hand knowledge and recommendations.
First, how important is it to check the backlash before beginning the removal of the gear assembly? Do I need to remove the pinion gear as well or just the gear assembly?
How difficult is it to get everything back on place once the seals are replaced? I have not done this type of repair before and am concerned I might miss something.
I am planning to replace all the ball joints at this time also, this was the primary reason for this maintenance in the first place.
2004 F150 Supercrew 4x4 Right now I have a broken roller cup on my rear U-joint. So I bought a new U-joint from the Ford dealer. When I pulled the driveshaft out I couldn't tell how to replace the U-joint. There are no E-clips to remove from the yoke/driveshaft ears. There are solid round "O" shaped clips that looked to be pressed in or something.
I've talked to the Ford dealer as well as a few other local mechanics and they haven't seen this setup before. So I didn't get any assistance there. It seems like my only option is to replace the whole pinion yoke, driveshaft, and U-joint together. Which sucks because this is just a frikkin' U-joint that needs replaced. That's it. I guess what I'm asking is, is there a way to work on this non-serviceable U-joint?
had a leaking rear driveshaft seal at the axle and replaced it and fluid. 75W145 full synthetic as recommended. it was changed at 128000 and I've started to get an axle whine over 25 MPH up to 65-70MPH. quites down around 80 MPH. I just checked it after 2 months (whine just started) with 133000. Any TSB. does this fall under TSB 05-23-3? Noise sounds like I've got really aggressive tires on the truck. Only have Dayton HT all season. Did not add the XL3 additive. Would this work at this juncture.
View 5 RepliesI have a 2006 F-150 Lariat with a 3.55 Ratio axle. What does the Axle Code H9 mean?
View 2 RepliesI am getting ready to put new axle shaft u-joints in my 2008 F350 (they are shot, they actually rattle on my rough roads). While I am at it I figure I will grease the front wheel brg cartridge, replace the needle brg that is inside the cartridge. I am also afraid I will the axle shaft vacuum seal. I don't want to go to ford an get raped, diesel O-rings doesn't have parts for the newer pickups and I don't want to get junk from the parts houses. Where I can get these parts for a reasonable price? What the best brands are? Are they the same parts as the earlier super duties? I know the lock out is different.
View 2 Replies156,000 miles, I've been pulling a 21ft bass boat in the summer for years with no issues. Now on hot days (over 78 degrees) it is over heating. Can't use AC and need to slow down to 60 mph in-order to cool her down. Never have flushed the radiator but I'm wondering if getting it flushed is a waste of time and if I should just proceed to replacing the radiator? For a couple of years now I can hear a roaring sound (like a jet engine) on really hot days, when I start out driving. Could this be a cooling fan? Seems like the power is restricted during these times. Really need to increase throttle to get going?
View 6 RepliesAlright, I, like alot of people with these trucks have the rust under their fuel doors from what ive seen and heard is the fuel neck filler plastic vibrating and rubbing, wearing throught the paint allowing water and fuel drips in and getting under the paint.
Well i keep touching up my spots but i have to do it twice a year and it just keeps getting worse, so i decided to go a bit further and clean it, touch it up, and protect it. This is a low $ job. Its not perfect but it is definately better than rust and from a couple feet back you can barely notice it, and hopefully this will be the last time i have to touch it up.
[URL] .....
I had a loud whine from the rear axle of my 04 SCREW and had the bearings replaced at the dealership. It has been about a year/12k miles since it was done and I just noticed that the vent hose is missing. I'm not sure if they left it off or if it fell off on its own. Anyway, my question is, do I need to replace the fluid once I put a new hose on? I'm not sure how much if any dirt or water might have gotten in there. Also, where does the hose go up to? I figure it must clip to the frame somewhere.
View 5 RepliesI own a 2004 F-150 FX4 5.7L V8, I notice this morning that I had gear oil coming out of my rear Axle Vent Tube. What would cause this issue? I'm kinda at a loss as to what would cause it.
View 3 Replies Just bought a 2007 supercab with the 5.4 in nice shape, but have an intermittent brake light on the dash. (No ABS, just the brake light.) Our mech. diagnosed a bad Brake Fluid Level switch. I can get a new sensor. I'd like to try and replace this myself and save a lot of money if it's not too difficult.
I'm looking for some clear step-by-step directions on doing this, and have a couple of questions:
Do I need to disconnect the battery first?
Do I need to empty the brake fluid reservoir? (Looks like the sensor is in the bottom of the reservoir, if I take it out without draining res, will I have a mess?)
When looking up the sensor online, I also saw the plug/connector for sale, should I replace that as well?
I have a 2006 F-15 XLT with a bed cover, tailgate cover and separate tailgate cap. The cap has cheap plastic clips that went into the tailgate but have broken off...this is a problem as I have a tonneau cover that is a tight fit. Every time I close the tailgate with the cover on, I have to jam the cap down and hope it is far enough by the time the tailgate closes.
2 Questions:
1) Where can I buy a reasonable replacement?
2) Is there a good solution to just repair? I tried JB Weld, but that did not seem to hold (surprisingly)
I have a leak between the metal and the plastic of my water crossover.
Do I need to remove the manifold to replace the gaskets for the crossover and if so looking for a good thread showing how.
In the last 50 starts it has happened twice: When I try to start the truck, all dash lights and power come on but there is no sound or cranking from the engine. If I cycle the key back and forth a half a dozen times it will then crank and start. Next time I will try and listen to hear if the solenoid is clicking.
I've read posts about it being the anti-theft, ignition switch, stater relay, ppm relay, etc....
I could replace the relays to rule them out, but my gut is telling me that's not it? Would there be a code from something like this?
Some family members borrowed my truck, and when they returned I have a loud whining noise coming from the rear axle, which I have determined is a 9.75 rear. I checked oil level and it was high enough, but has a slight leak from the pinion seal. Everything feels solid but I have nothing to compare it to.
Its on a 2005 Super Cab with the 5.4L 183,000 miles. The front pinion seal was replaced in Feb 2 years ago, by the dealer's mechanic, who may have been a shade tree mechanic.
I am a Youtube Certified Mechanic, as in, I watched about 10 videos of people working on their 9.75 differentials, and realize I don't have all of the tools to do the job, such as a press, or race drivers, or the special gauge.
How many of you have tackled this issue? What did you find? What am I looking at for cost? I am on a very small budget.
My '04 Prius is currently at 134k miles and I've noticed for a while that the front suspension feels and sounds "loose" over small bumps and imperfections on the road.
I also just started noticing some squeaking noise coming from the axle/hub when I first drive off in the morning.
I first thought the loose feeling could be worn out shocks, but I'm starting to worry that it would be something else.