Ford Super Duty (1999-2016) :: 2002 F250 - Replaced Idler / Tensioner / Belt But Still Getting Whipping Noise?
Jul 13, 2015
Ok I have a 2002 f250 7.3 4x4. The belt starting to shred and make a whiping sound at highway speed. So I replaced the idler, tensioner and belt. That was not the problem it still making noise so next I changed water pump. Still not it so I changed a/c clutch, bearing, and pulley. And It still not fixed. Right now the back of the belt is turning black on the wrighting like a pully is locking up. Also the front edge of the belt is starting to wear. I only have 255,000 miles on the truck and has been well maintained.
View 14 Replies
Advertisement
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
View 4 Replies
I have a 2002 f250 7.3 and the belt is rubbing front edge of the belt and making a whipping sound at 65 mph. Have replaced tensioner, idler, water pump and a/c bearing & pulley.
View 2 Replies
So from reading around a lot, it seems like the chirping is from the belt tensioner or idler pulley. That said, I've not been able to find anything definitive. I tried to do the water bottle squirt test (from Gates' youtube video) and either I did it wrong or the chirp did not go away implying the issue is not the belt. While I was looking in, I could see the tensioner shaking some.
If my tensioner should not be moving, do I just need the pulley or the pulley and the mount?
- Pulley [URL] ....
- Pulley and mount [URL] ....
Also, if the above items will fix the chirp, which brand would be best?
2007 RX 350, 113K.
Chirping gets worse as it heats up. Seems to happen independent of ambient temperature. Purchased a year ago so unsure of the history of part changes.
View 8 Replies
I bought a 2004 6.0L F-250 used a few weeks ago. There have been a few problems here and there that I have been competent enough to fix. I am now facing a problem of A: the truck not starting (I believe it was just a battery problem, charged and started fine). But also B: I have had a slightly frayed serpentine belt that I noticed a few days ago. After I got the truck running from my the no-start and driving it around the block I parked it and went inside. Came back out a few minutes later and I tried to start it. It hesitated a little bit but started with a loud whining noise and white smoke coming from the belt. Turned the engine off and saw on one of the bottom wheels (pulleys?) some residue that looked and smelled like burnt rubber. Is this just simply a need for a new belt?
View 5 Replies
2002 Camry 4 cyl. Can the idler pulley alone be replaced on the serpentine belt tensioner? I noticed a very slight side to side play when I had the belt off. No noise from it. When I looked at rock auto, they sell the whole bracket with the pulley.
View 2 Replies
2002 F250 V8 Gas 4x4 210 000kms
Just the other day noticed a whistle noise or a whining noise while I'm accelerating. Sounds like its coming from from the front passenger side,not sure.
View 8 Replies
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
View 11 Replies
I have a 2002 F-250 7.3. I was driving home from work on Tuesday (highway), I heard an intermittent noise coming from the front end, sounded like a rubbing/grinding noise. Yesterday on my way to wok, same thing, on and off. Yesterday on my way home the noise was constant, didn't go away. The noise comes at about 45mph and stays until I'm back under about 45mph, so mainly just on the highway. I put the truck in neutral and let off the pedal and the noise is still there which tells me it isn't engine related.
Yesterday after work I jacked up the front end, spun the tires, no noise. No play in the tires top/bottom or side/side. Took the tires off and what I did notice is the right axle u-joint is shot. I am hearing the noise in 2wd so I don't know if its the u-joint that's making the noise. Could it be a bad wheel hub bearing? Is it the u-joint? Maybe needle bearing??
View 6 Replies
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
View 8 Replies
I have a 2002 F250 with 189,000 miles. Im having some very bad issues that im trying to fix. The truck idles rough, with fluctuating RPM's. In certain speed reanges it also shakes and runs rough. If I turn the overdrive off the shaking pretty much stops, but it still accelerates pretty slowly. There is also a whistling noise from the front of the truck until the engine warms up, someone told me it sounds like a bad intake manifold? Does that sound right? What could be going on with my truck? All spark plugs and coil packs have been replaced, as well as the fuel injector rails.
View 2 Replies
2005 6.0 F250 SD Powerstroke... Truck died on the road and wouldn't start
The symptoms were... I changed the Radiator and had the cooling system flushed... couple of weeks later it stopped while driving... did some research and talked to a few people and the STC valve seemed to be the issue... So new STC, new intake gaskets, cleaned and new EGR gaskets and I just put in a new Turbo (Ford installed it)... had a stripped bolt under the EGR cooler arm and had to remove the Turbo to get to it.... 14 days later......
Changed STC fitting and gaskets in the high pressure oil pump, IPR screen, exhaust manifold gaskets and Cleaned the EGR and changed gaskets and no start. Tried starter fluid and it turned but wouldn't stay on and the batteries died. Would you all say I'm on the right path?
View 6 Replies
2002 F-250 7.3 4x4 ...
I have a rattling noise coming from the front suspension (both sides) when going over small bumps. Most people point to ball joints, but I find my case odd because I just replaced
Upper/Lower ball joints
Track bar
Tie rod ends
Shocks
Front U joints
Drag link
I did not touch the leaf springs or the sway bar, except to grease the links, which otherwise looked good.
View 3 Replies
I have a 2008 f 250 super duty gas v10 i have never had problems with it start always starts right up and strong. After coming out of the story today I tried the remote start and it tried to turn for a couple seconds and stopped. I replaced the battery and starter and still nothing. i hear the relay when trying to start with both keys or remote start but nothing from the starter all lights are working .
View 1 Replies
I have a 2005 F250 King Ranch 4X4 Diesel and now experiencing an issue with the front seat belts
The problem is while being worn sometimes they will not let you lean forward- they act like you have a foot on the brake pedal and are locked-you have to lean back and forth several times to get them to let out if reaching for something on the dash etc..
I have searched the forum and found many issues where the seat belts stopped retracting- but my issue seems to be unique in that the seat belt will at times 'Not Let Out" when you lean forward.
View 4 Replies
I have a 2003 F250 that has recently started blowing white smoke. I replaced the EGR Valve but no luck.
View 3 Replies
I am running a 2008 Ford F-250 with the DPF Delete and the Mini Maxx Tunner. I have replaced the ECT (Engine Coolant Temp Sensor) as well as the EGR Valve and housing troubleshooting this issue. Both the Engine light and the coolant icon come on when I turn on the vehicle. I am getting a P0117 Engine Coolant Temperature Circuit Low code on the Mini Maxx.
From a cold start with codes cleared if I turn the engine to ON even without starting the engine the Engine codes will come on and the the Mini Maxx will read engine coolant temp 302 and will go into Defueling Mode. I have repeatedly tried removing and reattaching the connector to the ECT thinking it could be loose connection. I can't drive the truck because there is no power and i know the engine is not hot because I have let it sit all night before doing these tests. I do not have a scanner to test other than the Mini Maxx. Other notes: I have checked Coolant I have checked Oil
View 3 Replies
2001 F250. My drivers side seat belt buckle randomly releases and it's getting worse. Any sources on a new one or used even. Also, what other vehicles may have the same part number if I go used.
View 10 Replies
You know the "mechanic's fiances truck" problem. I recently replaced the cam sensor in my 05' F250 Gas. The check engine light had been on for a while before that and my truck rode great, however I now want to sell it and I can't do that with a check engine light on. It's got about 85k miles on it.
After replacing the sensor, the light went off for about 20 miles, but it is now back on and my truck seems to miss every once in a while on acceleration or cruising. Some days it's worse than others. The check engine light still says cam sensor, but the sensor is brand new.
My fiance is a mechanic, so I don't know all the details about code numbers and such. However, I want to sell this truck pretty soon, and I would like it to run correctly. His dad (another mechanic) seems to think it could be a coil and wants to wait for that light to come on, but I would rather fix the problem and sell the truck!
View 1 Replies
I have a 2002 f250 4.2 diesel with a 5 speed manual box and i want to put a 7.3 in it. Does it fit?and can i make the 5 speed tranny fit?
View 4 Replies
My 2007,4.6 is making a whinning noise from the front of the engine around the idler/tensioner/alternator. What I have read it might be a problem with the alternator getting cold, I forgot to mention it's cold up here. Fixed by changing the alternator and did the noise come back as it seems to be a design problem?
View 12 Replies
